Nortel P0992639 01 - Manuals

P0992639 01 Modular ICS Companion Installer Guide Regulations Federal Communications Commission (U.S. only) The Federal Communications Commission (FCC) has designated UTAM Inc. to manage the installation and relocation of Unlicensed Personal Communication Services (UPCS). This includes Norstar Compa...

2 / Regulations Modular ICS Companion Installer Guide P0992639 01 Safety Do not connect the administration set or Base Stations directly to a CO line. Doing so may result in equipment damage. The Norstar administration set and base stations must not be used as off-premises equipment. Installers must...

P0992639 01 Modular ICS Companion Installer Guide Norstar Companion basics Norstar Companion provides mobility in the workplace. With Companion, your telephone can go with you, allowing you to make and receive calls while on the move. Calls that used to ring just at your desk can also appear and rin...

4 / Norstar Companion basics Modular ICS Companion Installer Guide P0992639 01 Before the base stations can be used in the United States, UTAM codes must be obtained and entered using an administration terminal or Norstar Remote Utilities (NRU). Please see Software keys (U.S. only) on page 67 for mo...

Norstar Companion basics / 5 P0992639 01 Modular ICS Companion Installer Guide If you are using Norstar Voice Mail with your Companion system, Version 3.0 is recommended as a minimum Voice Mail software version. For information on how to access Norstar Voice Mail using your Norstar Companion portabl...

P0992639 01 Modular ICS Companion Installer Guide Planning the installation Planning checklist å Verify that you have approval from UTAM Inc. (U.S. only) å Verify that a site planner determined base station locations and recorded them in the Provisioning Record . Required equipment and supplies å Co...

8 / Planning the installation Modular ICS Companion Installer Guide P0992639 01 Maximum number of Norstar Companion base stations on a system Configuring expansion modules With the addition of an Expansion Cartridge or a Combo Cartridge in the ICS, you can add Trunk Modules and/or Station Modules to...

Planning the installation / 9 P0992639 01 Modular ICS Companion Installer Guide On a mini system Note: Port 1 and 2 are on the ICS. On a mini or non-expanded system, port 1 on the ICS (station ports 101 to 132) is used for both base stations and Norstar sets. No fiber ports are used since no Station...

10 / Planning the installation Modular ICS Companion Installer Guide P0992639 01 Two-port Expansion Cartridge On a maxi system A system expanded to eight ports (maxi size) includes one 6-port expansion cartridge with fiber ports numbered 3 to 8, and 1 and 2 on the ICS. The base stations must be phys...

Planning the installation / 11 P0992639 01 Modular ICS Companion Installer Guide Six-port Expansion Cartridge with Companion On a mega system Keep in mind that 10 station modules is the limit for regular Norstar sets, and two station modules for Companion base stations is the limit on an XC configur...

12 / Planning the installation Modular ICS Companion Installer Guide P0992639 01 12-port Expansion Cartridge with Companion TM8 TM7 SM6 SM5 ICS (modules 1 and 2) SM4 SM3 SM14 SM13 SM12 SM11 SM10 SM9 To Ac outlet To Ac outlet Fiber Cable Guide (max. 7 modules per power bar) (max. 7 modules per power ...

Planning the installation / 13 P0992639 01 Modular ICS Companion Installer Guide Routing fiber cables 6-port Expansion Cartridge Fiber cableguide Upward routed fiber cable Downward routed fiber cable loose cables

14 / Planning the installation Modular ICS Companion Installer Guide P0992639 01 ICS numbering Non-expanded system (ICS alone) numbering Two-port Expansion Cartridge and ICS numbering Six-port Expansion Cartridge and ICS numbering Module # Lines Line ports B1 DN B2 DN DN ports Base station ports Por...

Planning the installation / 15 P0992639 01 Modular ICS Companion Installer Guide Twelve-port expanded system and ICS numbering Expansion module # Lines Line ports B1 DN B2 DN DN ports Base station ports PortableDN #14 — — — — — — — — — — 1401-1416 637-696 #13 — — — — — — — — — — 1301-1316 637-696 #1...

P0992639 01 Modular ICS Companion Installer Guide Installation Installation checklist When installing a Norstar system with Companion components, follow this installation checklist: å complete the wiring å install the Remote Power Interconnect units* å install the base stations* å install the extern...

18 / Installation Modular ICS Companion Installer Guide P0992639 01 Connecting expansion modules In order to keep the default port and extension numbering, connect Trunk Modules to the Expansion Cartridge beginning at the top and working down; connect Station Modules to the Expansion Cartridge begin...

Installation / 19 P0992639 01 Modular ICS Companion Installer Guide RPI unit There are two versions of the RPI unit: the RPI-8 BIX UL, which supports up to eight base stations; and the RPI-16 BIX UL, which supports up to 16 base stations. Each RPI has a connection board and either one (RPI-8 BIX UL)...

20 / Installation Modular ICS Companion Installer Guide P0992639 01 RPI Requirements Mounting the RPI unit 1. Position the screw holes for the RPI using the dimensions shown in the following figure. RPI mounting holes To provide adequate ventilation and to prevent overheating, leave a clearance of a...

Installation / 21 P0992639 01 Modular ICS Companion Installer Guide Mount RPIs at least 300 mm (12 in.) from the ceiling. 2. Insert wall plugs in the holes. 3. Partially screw in two #10 50-mm (2-in.) screws for the keyholes. 4. Open the hinged cover with a screwdriver by pushing in and then down to...

22 / Installation Modular ICS Companion Installer Guide P0992639 01 RPI components The RPI-8, which has only one power supply unit, has grounding straps and plates fitted so it can be upgraded to an RPI-16 (see illustration RPI components ). Wiring the RPI The maximum two-way DC loop resistance for ...

Installation / 23 P0992639 01 Modular ICS Companion Installer Guide Maximum power cabling distance (approximate) Depending on the size of cable you are using, you should remember the maximum cabling distances allowed between the RPI and the base station. RPI Connector Overview The following illustra...

24 / Installation Modular ICS Companion Installer Guide P0992639 01 Output connections Feed the output pairs in through the bottom of the RPI and route the pairs to the output connectors as shown in the following illustration. If only one pair is used for powering a base station, connect the power p...

Installation / 25 P0992639 01 Modular ICS Companion Installer Guide Input connector pinout Input wiring Connector Pin Signal Output connector IBIX1 1, 2 TCM 1 OBIX1 3, 4 TCM 2 OBIX2 5, 6 TCM 3 OBIX3 7, 8 TCM 4 OBIX4 IBIX2 1, 2 TCM 5 OBIX5 3, 4 TCM 6 OBIX6 5, 6 TCM 7 OBIX7 7, 8 TCM 8 OBIX8 IBIX3 1, 2...

26 / Installation Modular ICS Companion Installer Guide P0992639 01 RPI-8 BIX wiring chart Pin RPI Connector Board Label Wire color 26 OBIX1 BS1 -PWR White-Blue 1 Blue-White 27 TCM White-Orange 2 Orange-White 28 +PWR White-Green 3 Green-White 29 OBIX2 BS2 -PWR White-Brown 4 Brown-White 30 TCM White-...

28 / Installation Modular ICS Companion Installer Guide P0992639 01 RPI-16 BIX wiring chart Pin RPI Connector Board Label Wire color 26 OBIX9 BS9 -PWR White-Blue 1 Blue-White 27 TCM White-Orange 2 Orange-White 28 +PWR White-Green 3 Green-White 29 OBIX10 BS10 -PWR White-Brown 4 Brown-White 30 TCM Whi...

30 / Installation Modular ICS Companion Installer Guide P0992639 01 Installing base stations Before installing wireless equipment, ensure that a site planner has determined base station locations and recorded them. Before installing or relocating wireless equipment in the United States, verify that ...

Installation / 31 P0992639 01 Modular ICS Companion Installer Guide Position base stations away from an office area or where a portable is used by at least the amounts shown in the following table. Installing the base station on the ceiling or high on walls helps to maintain these minimum distances....

32 / Installation Modular ICS Companion Installer Guide P0992639 01 To mount a base station: 1. Fasten the bracket into position using two #8 38-mm (1½-in.) screws. 2. Route the cable from the ICS through the top (or bottom) opening. 3. Wind any excess cable around the posts to secure it, then faste...

Installation / 33 P0992639 01 Modular ICS Companion Installer Guide 5. Mount the base station onto the bracket, snapping it into position. 6. Connect the power RJ11 jumper lead to the RJ11 jacks on the termination board and the base station. 7. For plug-top power supplies only, connect the power sup...

34 / Installation Modular ICS Companion Installer Guide P0992639 01 Sliding cover onto bracket Installing portable telephones To use Norstar Companion portables, you must first install radio base stations to transceive radio signals to and from the portable telephones, then bring the system on-line....

Installation / 35 P0992639 01 Modular ICS Companion Installer Guide Note: Up to 60 portables can be installed on a Norstar wireless system. Each portable telephone must be registered to a DN before it can be used. By default, no Companion portables are assigned to the DNs. The range of portable exte...

Installation / 37 P0992639 01 Modular ICS Companion Installer Guide Installing external antenna and lightning surge arrestor procedures for the United States of America Installed antenna and lightning surge arrestor (USA) To ensure only recommended antennas are used: • the external antenna connector...

38 / Installation Modular ICS Companion Installer Guide P0992639 01 Planning for an outdoor external antenna (USA) When planning to install an outdoor external antenna: • Locate the antenna on the external wall of the building. • Keep the outdoor external antenna as close as possible to the base sta...

Installation / 39 P0992639 01 Modular ICS Companion Installer Guide Antenna with antenna bracket (USA) Installing a lightning surge arrestor (USA) Install the lightning surge arrestor to protect the Companion components from electrical surges. To install a lightning surge arrestor, follow these step...

40 / Installation Modular ICS Companion Installer Guide P0992639 01 Lightning surge arrestor and bracket (USA) Before you connect the ground lead to the lightning surge arrestor, attach it to an approved ground. Tip - The recommended wire gauge is 6 AWG. Connect the ground lead to the building groun...

Installation / 41 P0992639 01 Modular ICS Companion Installer Guide 2. Route and connect the coaxial cable from the outdoor external antenna to the lightning surge arrestor. 3. Route and connect the coaxial cable from the lightning surge arrestor to the appropriate base station connector. Installing...

42 / Installation Modular ICS Companion Installer Guide P0992639 01 antenna is used at a cell center, they should be spaced at least 0.5 m from each other to avoid radio interference problems. • Use RG-58/U co-axial cables to connect the antennas to the base stations. Installing an indoor directiona...

44 / Installation Modular ICS Companion Installer Guide P0992639 01 Installing an indoor omni-directional external antenna (Canada) 1. Insert the antenna in the bracket so that the antenna is vertical. 2. Mount the bracket to the wall or ceiling using two screws. 3. To prevent undue cable stress on ...

Installation / 45 P0992639 01 Modular ICS Companion Installer Guide Installing an outdoor omni-directional external antenna (Canada) When installing an outdoor omni-directional external antenna: • Locate the antenna on the external wall of the building. Note: The antenna must be mounted on a vertica...

46 / Installation Modular ICS Companion Installer Guide P0992639 01 Installing the outdoor omni-directional external antenna (Canada) To install an outdoor omni-directional external antenna, follow these steps: 1. Screw the antenna mounting plate vertically to the exterior wall of the building with ...

Installation / 47 P0992639 01 Modular ICS Companion Installer Guide 4. Rotate the mast until the threaded hole in the base of the mast is aligned with the set screw hole in the shroud, and then tighten the set screw. 5. Route the co-axial cable along the bottom edge of the plate between the shroud a...

48 / Installation Modular ICS Companion Installer Guide P0992639 01 Installing the lightning surge protector (Canada) 2. Before you connect the ground lead to the surge protector, attach it to an approved ground. The recommended wire gauge is 6 AWG (4 mm). Connect the ground lead to the building gro...

P0992639 01 Modular ICS Companion Installer Guide Powering up the system If you added a base station that requires a software update, the system begins downloading the software to the base station. The Administration Terminal display shows BS-1 Dload Start . Press CLEAR to clear the message. When th...

P0992639 01 Modular ICS Companion Installer Guide Programming Programming is performed by the installer or the customer service representative. The interface allows you to change settings for the entire Norstar system, plus settings for individual telephones and external lines. Most of the settings ...

52 / Programming Modular ICS Companion Installer Guide P0992639 01 Programming tools As with all Modular ICS programming, you can use a T7316 Business Series Terminal or an M7310 or M7324 Norstar set to perform the programming. In this book, all processes requiring dialpad buttons are presented in t...

Programming / 53 P0992639 01 Modular ICS Companion Installer Guide When you have completed your programming session, press ¨ . The display briefly reads End of session . Viewing your programming updates If any of the changes you have made to programming have not immediately taken effect, you see an ...

Programming / 55 P0992639 01 Modular ICS Companion Installer Guide Startup programming Before you perform Companion programming, your system should be running and configured. Startup programming is explained in the Modular ICS Installer Guide. Performing Startup 1. Enter the Startup access code from...

56 / Programming Modular ICS Companion Installer Guide P0992639 01 Changing the default template After entering the Startup access code and Installer password the display shows Reset memory? . 1. Press YES to select a default template. The display shows the current template. 2. Press CHANGE to choos...

Programming / 57 P0992639 01 Modular ICS Companion Installer Guide Entering programming for system coordinators The person on staff who is in charge of making changes on the Norstar system is called the system coordinator. The everyday Companion programming done by system coordinators is described i...

58 / Programming Modular ICS Companion Installer Guide P0992639 01 Entering programming using other passwords A set of the most often used headings and subheadings is available by using a System Coordinator password. This level of access is designed for the average user who takes care of the day-to-...

Programming / 59 P0992639 01 Modular ICS Companion Installer Guide 4. Individually register each Companion portable telephone. 5. Disable registration for the system. Changing the Registration password To ensure unauthorized portables are not registered to your system, a separate level of password a...

60 / Programming Modular ICS Companion Installer Guide P0992639 01 Companion programming Companion programming is found under the System programming heading. It includes the following subheadings: Registration You must enable registration for the entire Norstar system to allow individual portables t...

Programming / 61 P0992639 01 Modular ICS Companion Installer Guide Portable DNs Once registration is enabled for your Norstar Companion system, a series of extension numbers (637 to 696) automatically becomes available for registration. Check that an extension number is still available before regist...

62 / Programming Modular ICS Companion Installer Guide P0992639 01 Deregistering a portable Deregister an extension number when: • the portable must be replaced due to loss or breakage • the owner departs and you want to assign the handset to someone else with a different telephone number Press ≠ an...

Programming / 63 P0992639 01 Modular ICS Companion Installer Guide After installing Norstar Companion components and obtaining the proper number of UTAM activation keys (see Software keys (U.S. only) on page 67), you need to verify that wireless re-evaluation has occurred. Alarm code messages can be...

64 / Programming Modular ICS Companion Installer Guide P0992639 01 Radio credits (U.S. only) Press CREDIT to see the number of radio credits available and the total number of radio credits. Verify that the total number of radio credits is enough to support the system you have just installed. The num...

Programming / 65 P0992639 01 Modular ICS Companion Installer Guide Cells Cell programming allows you to examine the cell radio and cell neighbor configuration. Choose the cell you want to examine by pressing ≠ and the cell number (01 to 32) or select LIST to see all in sequence. When in the list mod...

66 / Programming Modular ICS Companion Installer Guide P0992639 01 Cell rad nghbrs This sub-heading allows you to view the two-digit number of any cells that border a particular cell in a system, these are called cell neighbors. As well, you can view any cells that border the cell neighbors. Press ≠...

Programming / 67 P0992639 01 Modular ICS Companion Installer Guide There are only two reasons to modify the system LID. • The site has multiple systems, and you want users to be able to move from system to system without changing slots on their portable telephones. All systems must be set to the sam...

68 / Programming Modular ICS Companion Installer Guide P0992639 01 The Software keys can be obtained and entered using the following steps. Step 1: Obtain the Companion ID The Companion ID Label is sent to each customer once radio credits have been purchased. In order to implement the credits and ta...

Programming / 69 P0992639 01 Modular ICS Companion Installer Guide Step 2: Obtain the System Identification Number Obtain the System ID (SysID) by pressing ²¥¥êçêéë , or ²¥¥àáàÝÜ on any programming set. This information is also available by accessing Software keys in an Installer programming session...

70 / Programming Modular ICS Companion Installer Guide P0992639 01 3. Indicate the number of radio credits you require. You need two credits for every base station in your system. 4. You are given two keys, the UTAM Activation Key and the Credit Key. The keys consist of three separate numeric string...

Programming / 71 P0992639 01 Modular ICS Companion Installer Guide 3. Press ≠ . The display reads Key 1:_ . 4. Enter the 8 digit password number for Key 1. Use BKSP to make corrections. The display reads Key 2:_ . 5. Enter the eight-digit password number for Key 2. Proceed as above until you have fi...

72 / Programming Modular ICS Companion Installer Guide P0992639 01 Register your Companion portables Norstar Companion Portable telephones are added to the system using the portable registration process. Refer to the Modular ICS Companion System Coordinator Guide for more information on registering ...

P0992639 01 Modular ICS Companion Installer Guide Registering individual portables Registering the C3060 The following section describes the procedures involved in registering Companion C3060 portable telephones. To register each portable with the Norstar system, you must do two things: • Register t...

Registering individual portables / 75 P0992639 01 Modular ICS Companion Installer Guide 7. Enter up to 16 characters for the system name. For example, NORTEL 1 . • Press the dial pad key until the letter you need appears on the display. For example, press key 5 three times to display the letter L. •...

76 / Registering individual portables Modular ICS Companion Installer Guide P0992639 01 2. Make a call. a. Press i . You hear dial tone, and the display shows LINK . If you do not hear dial tone, check that you have selected the correct system and that the associated desk telephone is idle or regist...

Registering individual portables / 77 P0992639 01 Modular ICS Companion Installer Guide If a portable is registered on other systems, it will still be available on those systems. You deregister one system at a time. Note: If you are out of range of the system, this procedure clears registration data...

78 / Registering individual portables Modular ICS Companion Installer Guide P0992639 01 by the signal strength and power mode. For example, 14112 - 67 . Hand-off occurs normally between the cells. Note: In this example, the module is 14 , the port is 11 and the radio is 2 . The signal strength measu...

80 / Registering individual portables Modular ICS Companion Installer Guide P0992639 01 Registering the C3050 The following section describes the procedures involved in registering Companion C3050 portable telephones. To register each portable with the Norstar system, you must do two things: • Regis...

82 / Registering individual portables Modular ICS Companion Installer Guide P0992639 01 To confirm that the C3050 is registered 1. Close, then open the portable flap. If the portable displays the system name that you just registered, proceed to step 5. If the portable displays a different system nam...

Registering individual portables / 83 P0992639 01 Modular ICS Companion Installer Guide Deregistering the C3050 You can deregister the C3050 in two ways: • from the portable • from the administration set You can deregister the portable to clear information stored in the portable and the system. To d...

84 / Registering individual portables Modular ICS Companion Installer Guide P0992639 01 Measuring RSSI for a C3050 The Receive Signal Strength Indicator (RSSI) is a measurement of the signal strength the base station receives from the portable. The base station controls the power transmitting mode o...

Registering individual portables / 85 P0992639 01 Modular ICS Companion Installer Guide Measuring directed RSSI You may want to measure the RSSI between a portable and a specific base station radio. For example, you may suspect that one of the two radios in a base station is not working properly. Yo...

86 / Registering individual portables Modular ICS Companion Installer Guide P0992639 01 3. Press Ò or L . 4. Press °•ªª . 5. Enter the five-digit ID code for the base station radio you want to measure. The portable displays this ID followed by the signal strength, for example 03142 - 54 . Hand-off d...

Registering individual portables / 87 P0992639 01 Modular ICS Companion Installer Guide If the display does not show Office n: Free ., follow the procedures in Deregistering the C3020 (Canada only) on page 88 to overwrite the system number then return to step 2 of this procedure. 5. Press s , then p...

Registering individual portables / 89 P0992639 01 Modular ICS Companion Installer Guide 4. Press s , then press 0 . The display shows Deregister? . 5. Press s , then press 0 again. The display shows Deregistering... and then Deregistered . 6. To continue using the portable, press r . Measuring RSSI ...

Registering individual portables / 91 P0992639 01 Modular ICS Companion Installer Guide Before you begin measuring directed RSSI Use the Companion Provisioning Record to find and note the following: • the five-digit radio ID of the base station you want to measure, by mapping the base station locati...

92 / Registering individual portables Modular ICS Companion Installer Guide P0992639 01 After registering the portables When you have completed programming the system, use the following checklist to ensure you completed the required tasks. å Register the portables. å Verify Portable Credits. å Ensur...

P0992639 01 Modular ICS Companion Installer Guide Testing Testing the Companion portable telephones You must register all portable telephones before testing them. For more detail on registering portable telephones, refer to Modular ICS Companion System Coordinator Guide and the Telephone Registratio...

94 / Testing Modular ICS Companion Installer Guide P0992639 01 A solid red light indicates that both radios on the base station are busy, that the ICS is downloading data to the base stations, or that one or both radios have not been assigned to a cell. 4. Using the directed Received Signal Strength...

P0992639 01 Modular ICS Companion Installer Guide Troubleshooting The following sections describe some basic troubleshooting techniques to try with a malfunctioning portable telephone or base station. Problems with a portable telephone 1. Verify that the portable is compatible with the software vers...

Troubleshooting / 97 P0992639 01 Modular ICS Companion Installer Guide Replacing a base station To replace a base station, you do not have to power down the ICS. When you replace a base station, no portable registration information is lost. After a short boot sequence, the base station should be fun...

98 / Troubleshooting Modular ICS Companion Installer Guide P0992639 01 Verifying Radio Credits (U.S. only) You need the programming template found at the front of the Modular ICS System Coordinator Guide . 1. Press ²¥¥ÛßßÜÝÝ ( ¥¥‚¯öìéí ). 2. Press ÛßßÜÝÝ (the default Installer password). 3. Press ‘ ...

Troubleshooting / 99 P0992639 01 Modular ICS Companion Installer Guide Problems with an RPI To troubleshoot an RPI, follow these steps: 1. Verify that the RPI is plugged into a working AC outlet. 2. Verify that all the connections to the RPI, including the power cord, jumper lead, input and output, ...

100 / Troubleshooting Modular ICS Companion Installer Guide P0992639 01 Problems with wireless communication Obtaining a Recovery Key A disabled Norstar Companion system implies that base stations and portables are not operational. UTAM registering information is, however, retained. To reactivate No...

Troubleshooting / 101 P0992639 01 Modular ICS Companion Installer Guide If you need a Regression Key, follow these steps: 1. Record the new System Identification Number once the system is powered up. See Step 2: Obtain the System Identification Number on page 69 for more information. 2. Locate the f...

102 / Troubleshooting Modular ICS Companion Installer Guide P0992639 01 Alarm codes For a complete list of Norstar alarms, consult the Norstar Alarm & Event Code Manual . Also consult the Modular ICS Installer Guide . Displays Example display Meaning Possible causes and actions Alarm: 21 Wireles...

106 / Troubleshooting Modular ICS Companion Installer Guide P0992639 01 Event messages Event message display Cause (U.S. only) Unable to activate all registered portables. The system ran out of portable credits. One event is generated per portable that failed to activate. The repetition of the corre...

P0992639 01 Modular ICS Companion Installer Guide Specifications This chapter provides the specifications for Companion equipment. Norstar Companion system components Remote Power Interconnect The Remote Power Interconnect (RPI) device power lines are protected by 3 A, 250 V anti-surge fuses. Each o...

114 / Specifications Modular ICS Companion Installer Guide P0992639 01 Base station The base station consists of two printed circuit boards: the Line Interface Module (LIM) and the Dual Radio Interface Module (RIM). The base station provides connectors for a terminating line cord, external antennas,...

Specifications / 115 P0992639 01 Modular ICS Companion Installer Guide Base station plug-top power supply External antenna assembly (For the US) Part no. A0386334 Color Dolphin Gray AC supply voltage 120 V AC supply frequency 60 Hz Secondary voltage 12 V Secondary current 800 mA Operating temperatur...

116 / Specifications Modular ICS Companion Installer Guide P0992639 01 Outdoor omni-directional antenna (For Canada) Indoor omni-directional antenna (For Canada) Part no. A0383818 Frequency range 944 to 952 MHz Peak power rating 10 mW minimum Peak antenna gain 4 dBi maximum Polarization vertical Inp...

Specifications / 117 P0992639 01 Modular ICS Companion Installer Guide Indoor directional antenna (For Canada) Lightning surge protector (For Canada) Part no. A0383817 Frequency range 944 to 952 MHz Peak power rating 10 mW minimum Peak antenna gain 5 dBi maximum Polarization vertical Input impedance...

P0992639 01 Modular ICS Companion Installer Guide Upgrading your system Adding Companion to a mini, midi, maxi, or mega system On a mini system (non-expanded), only module 1 (ports 101 to 132) can be used for Companion base stations and/or wireline sets. Module 2 is used for trunk modules only. On a...

120 / Upgrading your system Modular ICS Companion Installer Guide P0992639 01 To upgrade an RPI-8 to an RPI-16 1. Power down the RPI. 2. Unscrew the grounding straps and plates. 3. Add the second power supply unit (A0385554, NPS 50376L106) and screw down the grounding straps, the grounding plates, a...

P0992639 01 Modular ICS Companion Installer Guide Glossary A alarm code: A number that appears on the alarm telephone's display, informing you that the ICS has detected a fault in the system. Analog Terminal Adapter (ATA): A device that permits the connection of analog telecommunication devices such...

P0992639 01 Modular ICS Companion Installer Guide Index A activating disabled system 1 , 68 wireless communication 1 , 68 , 101 activation key (see UTAM)alarm code Alarm 200 102 Alarm 201 102 Alarm 202 102 Alarm 203 103 Alarm 204 103 Alarm 205 103 Alarm 206 103 Alarm 207 103 Alarm 208 103 Alarm 209 ...

Backup programming overlays Business Series Terminals Programming Overlay P0914001 01 Heading Back Show Next Heading Back Next Show Norstar Programming Overlay PO698666 Issue 02 Printed in Canada