Nortel 8306 - Manuals

MIC notice for 8310, and 8306 chassis (Republic of Korea only) 7 European Union and European Free Trade Association (EFTA) Notice All products labeled with the CE marking comply with R&TTE Directive(1999/5/EEC) which includes the Electromagnetic Compliance (EMC)Directive (2004/108/EC) and the Lo...

8 Regulatory Information and Safety Precautions National Safety Statements of Compliance CE Marking Statement (Europe only) EN 60 950 Statement This is to certify that the Nortel 8300 Series chassis and componentsinstalled within the chassis are in compliance with the requirements of EN60 950 in acc...

10 Regulatory Information and Safety Precautions Fax: 52 5 480 2199 Embarcar a: (8306 and 8310 Chassis) 8301AC:100 to 240 VAC 16A 47 to 60 Hz por fuente de poder 8301AC: 200 to 240 VAC 12 A 47 to 60 Hz por fuente de poderuna fuente, una fuente + configuraciones de una fuente redundante, dosfuentes o...

Safety Messages 11 Notices Notice paragraphs alert you about issues that require your attention.The following sections describe the types of notices. For a list of safetymessages used in this guide and their translations, see "Translations ofsafety messages". Attention Notice ATTENTION An at...

15 . Software license This section contains the Nortel Networks software license. Nortel Networks Inc. software license agreement This Software License Agreement ("License Agreement") is betweenyou, the end-user ("Customer") and Nortel Networks Corporation andits subsidiaries and aff...

16 Software license of this Agreement. Customer shall not a) use, copy, modify, transferor distribute the Software except as expressly authorized; b) reverseassemble, reverse compile, reverse engineer or otherwise translate theSoftware; c) create derivative works or modifications unless expresslyaut...

19 . New in this release The following sections detail what’s new in Nortel Ethernet Routing Switch8300 Installation — Chassis Installation and Maintenance, NN46200-309for Release 4.1: • “Features” (page 19) • “Other changes” (page 19) Features See the following sections for information about featur...

21 . Introduction The Nortel Ethernet Routing Switch 8300 chassis provides the physicalframework for the Nortel Ethernet Routing Switch 8300 modules. This document provides the instructions for installing the Nortel EthernetRouting Switch 8300 chassis (8306 and 8310 chassis) in an equipmentrack. Thi...

23 . Chassis installation fundamentals This chapter describes fundamental information that you need for installingthe Ethernet Routing Switch 8300 chassis (8306 and 8310 chassis) . Each Ethernet Routing Switch 8300 chassis consists of a sheet metalenclosure and a backplane. The number of bays for fa...

24 Chassis installation fundamentals modules. Slots are numbered from the top down. You can install 8300Series I/O switch modules in slots 1 through 4 and slots 7 through 10.Slots 5 and 6 are reserved for the 8393SF/CPU or 8394SF/CPU modules. The Ethernet Routing Switch 8310 chassis has three bays f...

Ethernet Routing Switch 8306 chassis 25 Figure 1Ethernet Routing Switch 8310 chassis and components Ethernet Routing Switch 8306 chassis The Ethernet Routing Switch 8306 chassis provides four slots forinstalling I/O modules and two slots for installing Ethernet Routing Switch8393SF/CPU or 8394SF/CPU...

26 Chassis installation fundamentals • Ethernet Routing Switch 8348TX-PWR module or • Ethernet Routing Switch 8348GTX-PWR module CAUTION Risk of equipment damage Do not install Ethernet Routing Switch 8300 modules andEthernet Routing Switch 8100 or 8600 modules within the samechassis. Ethernet Routi...

Site requirements 27 • 8005DC • 8005DI DC, The PoE feature requires the following components: • Ethernet Routing Switch 8306 or 8310 chassis with PoE backplane • Ethernet Routing Switch 8301AC or 8302AC power supply • Ethernet Routing Switch 8393SF/CPU or 8394SF/CPU module and a choice of either of ...

28 Chassis installation fundamentals Use the following guidelines to plan front and rear access: • The maintenance aisle in front of the frame requires a clearance of76.2 centimeters (cm) (30 inches). • The wiring aisle at the back of the frame requires a clearance of 61 cm(24 inches). AC input elec...

Hardware requirements 31 Figure 4Items in the Ethernet Routing Switch 8306 chassis shipping container Other equipment In addition to the items that are included in the Ethernet Routing Switch8310 and 8306 chassis accessory package you must also supply otheritems. Before you install the hardware, ens...

32 Chassis installation fundamentals Cables Unless you specifically order them, the cables required for your networkconfiguration are not included in the chassis accessory package. If you donot have the proper cables, contact your network administrator. Mounting hardware for the 8310, 8306 chassis T...

33 . Ethernet Routing Switch 8310 and 8306chassis installation This section describes how to install the Ethernet Routing Switch 8310and 8306 chassis. CAUTION ESD To prevent damage from electrostatic discharge, always wearan antistatic wrist strap connected to an electrostatic discharge(ESD) jack wh...

Installing the chassis on a flat surface 35 • “Mounting the Ethernet Routing Switch 8310 and 8306 chassis in anequipment rack” (page 36) • “Installing the cable guides” (page 40) Chassis installation time requirements The following table lists procedures you must use to install the NortelEthernet Ro...

36 Ethernet Routing Switch 8310 and 8306 chassis installation Prerequisites • Provide adequate space around the unit for access to cableconnectors. • Ensure that the surface can safely support the weight of the chassis,its components, and its attached cables. See “Chassis installation time requireme...

40 Ethernet Routing Switch 8310 and 8306 chassis installation --End-- Procedure job aid: Maximum number of chassis installed in 7-foot rack The following table shows the maximum number of chassis that you caninstall in a 7-foot rack. Chassis Maximum number of chassis installed in 7-foot rack 8310 3 ...

43 . Switch operations This chapter describes some of the procedures that you perform tooperate the Ethernet Routing Switch 8300 and provides troubleshootinginformation. Navigation • “Powering on DC power supplies” (page 43) • “Powering on AC power supplies” (page 44) • “Resetting the switch” (page ...

44 Switch operations ATTENTION When you first install a chassis that contains two or threepower supplies, you must turn on two of the power supply unitssimultaneously. If you wait longer to turn on the second powersupply, one of the power supplies could shut down. To correct thiscondition, turn off ...

Resetting the switch 45 The number of supported Power over Ethernet (PoE) modules depends onthe power supply rating (110 volts [V]AC nominal or 220 VAC nominal),the power supply model, and the number of power supplies. For moreinformation, see Ethernet Routing Switch 8300 Planning — PowerConsiderati...

46 Switch operations Procedure steps Action To warm-start the Ethernet Routing Switch 8300 Series (nodiagnostic tests are run), press the Reset button for less than 5seconds. To press the Reset button, insert a small pointed object (forexample, an unbent paper clip) into the Reset button hole. The f...

Removing removable flash memory cards 47 2 Insert the card into the card receptacle. 3 Gently push the card in until it fits snugly in place. --End-- Removing removable flash memory cards Remove a removable flash memory card from the Ethernet RoutingSwitch 8393SF/CPU or 8394SF/CPU module to stop usi...

48 Switch operations Protecting memory card files Write-protect the memory card for backup purposes after you successfullyload the configuration file and save your configuration because Nortelships each memory card with the read-write protect switch in theunprotected position. Typically, you do not ...

51 . Part Numbers This chapter provides a list of Nortel Ethernet Routing Switch 8300hardware and part numbers. The following table lists Ethernet Routing Switch 8300 hardware and partnumbers. Table 4Ethernet Routing Switch 8300 hardware part numbers Part number Item Additional details DS1402007-E5 ...

55 . Technical specifications This chapter lists the physical, environmental, and electrical specificationsfor the Ethernet Routing Switch 8310 and 8306 chassis and the availablepower supplies. Navigation • “Ethernet Routing Switch 8310 chassis specifications” (page 55) • “Ethernet Routing Switch 83...

56 Technical specifications Table 5Ethernet Routing Switch 8310 chassis physical specifications (cont’d.) Physical specifications Depth: 19.9 in. (50.5 cm) Weight (empty): 85 pounds (lb) (39 kilograms [kg]) Weight (fully loaded): 225 lb (102 kg) Cooling system: Fan trays: 2 per chassis Fans: 8 per f...

Ethernet Routing Switch 8306 chassis specifications 57 Table 7Ethernet Routing Switch 8310 international regulatory requirements (cont’d.) International regulatory requirements U.S.: FCC CFR47 Part 15, Subpart B, ClassA Canada: ICES-003, Issue-2, Class A Europe: EN 55022-1998 Class A; EN61000-3-2/A1...

Ethernet Routing Switch 8301 AC power supply specifications 59 Table 10Ethernet Routing Switch 8306 international regulatory requirements (cont’d.) International regulatory requirements Europe: EN 55022-1998 Class A; EN 61000-3-2/A14,EN 61000-3-3 (CE Marking) Australia/NewZealand: AS/NZS 3548:1995, ...

60 Technical specifications Table 11Ethernet Routing Switch 8301 AC power specifications (cont’d.) DC Output Power Ratings Max. output power(combined): 1140 W (1050 W + 90W fans) 1770 W (1680 W + 90W fans) Non-PoE: 3.3 VDC @ 150 A 3.3 VDC @ 150 A 12 VDC @ 65 A 12 VDC @ 65 A PoE: 50 VDC @ 18 A 50 VDC...

Ethernet Routing Switch 8005DC power supply specifications 61 Table 12Ethernet Routing Switch 8302 AC power specifications (cont’d.) Heat dissipation (thermal/output): 1126 BTU/hr 1195 BTU/hr Hold-up time: 20 ms 20 ms DC Output Power Ratings Max. output power (combined): 850 W (760 W + 90 W fans) 14...

62 Technical specifications The following table lists the DC output power specifications. Parameter Specifications Output power (maximum) 1462 W (1372 W + 90 W fans) Modules 3.3 V @ 150 A 12 V @ 72 A Fans 12 VDC @ 7.5 A/ 24 A peak Mean time before failure (MTBF) 108 803 hr(Bellcore TR–332 standard) ...

63 . Translations of safety messages Class A device caution statement CAUTION This device is a Class A product. Operation of this equipmentin a residential area is likely to cause harmful interference, inwhich case users are required to take appropriate measuresnecessary to correct the interference ...

64 Translations of safety messages CAUTION ATTENZIONE Questo dispositivo è un prodotto di Classe A. Il funzionamentodi questo apparecchio in aree residenziali potrebbe causareinterferenze dannose, nel cui caso agli utenti verrà richiestodi adottare tutte le misure necessarie per porre rimedio allein...

Electrostatic discharge caution statement 65 CAUTION ATTENZIONE ESD Per evitare danni derivanti da scariche elettrostatiche, indossaresempre un polsino antistatico collegato a una presa di scaricoelettrostatico (ESD) durante la manutenzione del prodotto.Accertarsi che il polsino sia a contatto con l...

Nortel Ethernet Routing Switch 8300 Installation — Chassis Copyright © 2008 Nortel NetworksAll Rights Reserved. Printed in Canada and the United States of AmericaRelease: 4.1 Publication: NN46200-309 Document status: Standard Document revision: 01.01 Document release date: 16 June 2008 To provide fe...