Lexmark 279 - Manuals

1 2 3 4 5 1 1 Right side 300 mm (12 in.) 2 Front 510 mm (20 in.) 3 Left side 200 mm (8 in.) 4 Rear 200 mm (8 in.) 5 Top 540 mm (21 in.) Printer configurations CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or print...

1 2 3 4 8 9 10 7 6 5 1 Printer control panel 2 Automatic document feeder (ADF) 3 ADF tray 4 ADF bin 5 Front door release button 6 Standard 250 ‑ sheet tray 7 Optional 250 ‑ or 550 ‑ sheet tray 8 50 ‑ sheet multipurpose feeder 9 Paper stop 10 Standard bin Understanding the basic functions of the scan...

Using the ADF and scanner glass Automatic document feeder (ADF) Scanner glass Use the ADF for multiple ‑ page documents. Note: The ADF scans only one side of the page. Use the scanner glass for single ‑ page documents, book pages, small items (such as postcards or photos), transparencies, photo pape...

Additional printer setup Installing internal options CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electircal outlet before continui...

Installing an optional card CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electrical outlet before continuing. If you have other dev...

4 Push the card firmly into place as shown in the illustration. Warning—Potential Damage: Improper installation of the card may cause damage to the card and the controller board. Note: The entire length of the connector on the card must touch and be flushed against the controller board. 5 Close the ...

CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electrical outlet before continuing. If you have any other devices attached to the pri...

Attaching cables CAUTION—SHOCK HAZARD: Do not use the fax feature during a lightning storm. Do not set up this product or make any electrical or cabling connections, such as the fax feature, power cord, or telephone, during a lightningstorm. Connect the printer to the computer using a USB cable or t...

Use the To 5 LINE port Connect the printer to an active telephone line through a standard wall jack (RJ ‑ 11), DSL filter, or VoIP adapter, or any other adapter that allows you to access the telephone line to sendand receive faxes. 6 USB printer port Connect the printer to a computer. 7 Security slo...

Networking Notes: • Purchase a MarkNet TM N8352 wireless network adapter first before setting up the printer on a wireless network. For information on installing the wireless network adapter, see the setup sheet that came with the adapter. • A Service Set Identifier (SSID) is a name assigned to a wi...

• Security Method —There are four basic options for Security Method: – WEP keyIf your network uses more than one WEP key, then enter up to four in the provided spaces. Select the keycurrently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphraseWP...

Use To Search for networks Show available wireless connections. Note: This menu item shows all broadcast secured or unsecured SSIDs. Enter a network name Manually type the SSID. Note: Make sure to type the correct SSID. Wi ‑ Fi Protected Setup Connect the printer to a wireless network using Wi ‑ Fi ...

Connecting the printer to a wireless network using the Embedded Web Server Before you begin, make sure that: • Your printer is connected temporarily to an Ethernet network. • A wireless network adapter is installed in your printer and working properly. For more information, see theinstruction sheet ...

Printing a network setup page If the printer is attached to a network, then print a network setup page to verify the network connection. This pagealso provides important information that aids network printing configuration. 1 From the printer control panel, navigate to: > Settings > > Repor...

Loading paper and specialty media The selection and handling of paper and specialty media can affect how reliably documents print. For more information,see “Avoiding jams” on page 164 and “Storing paper” on page 49 . Setting the paper size and type 1 From the printer control panel, navigate to: >...

Loading the multipurpose feeder Use the multipurpose feeder when printing on different paper sizes and types or specialty media, such as card stock,transparencies, paper labels, and envelopes. You can also use it for single ‑ page print jobs on letterhead. 1 Open the multipurpose feeder. a Pull the ...

• Load envelopes with the flap on the left side facedown. Warning—Potential Damage: Never use envelopes with stamps, clasps, snaps, windows, coated linings, or self ‑ stick adhesives. These envelopes may severely damage the printer. 5 From the printer control panel, set the paper size and paper type...

Creating a custom name for a paper type Using the Embedded Web Server 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address in the TCP/IP section in the Network/Ports menu. The IP address appears as foursets of numbers separated by peri...

Paper and specialty media guide Notes: • Make sure the paper size, type, and weight are set correctly on the computer or control panel. • Flex, fan, and straighten specialty media before loading them. • The printer may print at a reduced speed to prevent damage to the fuser. • For more information o...

Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extendthe time to several days if the storage or transportation environment is very different from the printer environment.Thick paper may also require a longer conditioning period. Grain d...

While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers thatrepresent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigorand discipline. Many factors are taken into consideration both...

• Preprinted papers that require a registration (the precise location on the page) greater than ± 2.3 mm (± 0.9 in.),such as optical character recognition (OCR) forms. In some cases, registration can be adjusted with a softwareapplication to successfully print on these forms.) • Coated papers (erasa...

Paper size and dimension Standard 250 ‑ sheet tray Optional 250 ‑ or 550 ‑ sheet tray Multipurposefeeder ADF Scannerglass Duplexprinting B5 Envelope 176 x 250 mm(6.93 x 9.84 in.) X X X X Other Envelope 85.7 x 165 mm to215.9 x 355.6 mm(3.375 x 6.50 in. to8.5 x 14 in.) X X X 4 X 1 Paper is supported o...

Paper type 250 ‑ or 550 ‑ sheet tray Multipurpose feeder Duplex mode ADF Scanner glass Heavy paper Rough/Cotton X Custom Type [x] 1 One ‑ sided paper labels designed for laser printers are supported for occasional use. We recommend printing only up to 20 pages of paper labels per month. Vinyl, pharm...

• To optimize performance and minimize jams, do not use envelopes that: – Have excessive curl or twist – Are stuck together or damaged in any way – Have windows, holes, perforations, cutouts, or embossing – Have metal clasps, string ties, or folding bars – Have an interlocking design – Have postage ...

When printing on card stock: • Make sure the Paper Type is Card Stock. • Select the appropriate Paper Texture setting. • Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams orother paper handling problems. • Check with the manufacturer or ve...

Printing Printing a document Printing a document 1 From the Paper menu on the printer control panel, set the paper type and size to match the paper loaded. 2 Send the print job: For Windows users a With a document open, click File > Print . b Click Properties , Preferences , Options , or Setup . ...

Using the printer control panel 1 From the printer control panel, navigate to: > Settings > > Print Settings > > Quality Menu > > Toner Darkness 2 Adjust the toner darkness, and then press . Printing from a mobile device To download a compatible mobile printing application, visi...

Printing confidential and other held jobs Note: Confidential and Verify print jobs are automatically deleted from memory after printing. Repeat and Reserve jobs are held in the printer until you choose to delete them. For Windows users 1 With a document open, click File > Print . 2 Click Properti...

• If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings tab > Security > Confidential Print Setup . 3 Modify the settings: • Set a maximum number of PIN entry attempts. When a user exceeds a specific number of PIN entry attempts,all of th...

Copying Automatic document feeder (ADF) Scanner glass Use the ADF for multiple ‑ page documents. Note: The ADF scans only one side of the sheet. Use the scanner glass for single-page documents, book pages, small items(such as postcards or photos), transparencies, photo paper, or thin media(such as m...

• The ADF indicator light comes on when the paper is loaded properly. 2 Adjust the paper guides. 3 From the printer control panel, use the keypad to enter the number of copies, and then press . Copying using the scanner glass 1 Place an original document facedown on the scanner glass in the upper le...

3 From the printer control panel, navigate to: > Copy > > Copy from > select the size of the original document 4 Navigate to: Copy to > > select the tray containing the transparencies > > select the number of copies or enter a number on the keypad > 5 If there are no trays...

Note: If you want to copy another document, then place it on the scanner glass, press the left or right arrow button to scroll to Scan the Next Page , and then press . 6 Press the left or right arrow button to scroll to Finish the Job , and then press . Customizing copy settings Copying to a differe...

4 Navigate to: Copy to > > select the tray containing the paper size and type you want to use > > select the number of copies or enter a number on the keypad > 5 If there are no trays that contain the paper size and type you want to use, then do the following: a Navigate to: Copy to &...

• The ADF indicator light comes on when the paper is loaded properly. 2 If you are loading a document into the ADF tray, then adjust the paper guides. 3 From the printer control panel, navigate to: > Copy > > Darkness > adjust the darkness setting > select the number of copies or ente...

6 Select the number of copies or enter a number on the keypad, and then press . Note: If you want to copy another document, then place it on the scanner glass, press the left or right arrow button to scroll to Scan the Next Page , and then press . 7 Press the left or right arrow button to scroll to ...

3 From the printer control panel, navigate to: > Copy > > Separator Sheets 4 Select Between Copies , Between Jobs , Between Pages , or Off . 5 Select the number of copies or enter a number on the keypad, and then press . Note: If you want to copy another document, then place it on the scann...

Notes: • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazineclippings) into the ADF tray. Place these items on the scanner glass. • The ADF indicator light comes on when the paper is loaded properly. 2 If you are loading a document into the ADF tr...

• To set the printer to automatically detect the size of the original document, press the left or right arrow button to scroll to Auto Size Sense , and then press . Copy to This option lets you select the paper size and type on which your copies will be printed. • To scroll to the paper size and typ...

E-mailing Automatic document feeder (ADF) Scanner glass Use the ADF for multiple ‑ page documents. Note: The ADF scans only one side of the sheet. Use the scanner glass for single-page documents, book pages, small items(such as postcards or photos), transparencies, photo paper, or thin media(such as...

3 Enter the appropriate information, and then click Submit . Creating an e-mail shortcut Creating an e-mail shortcut using the Embedded Web Server 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address in the TCP/IP section in the Networ...

Faxing Automatic document feeder (ADF) Scanner glass Use the ADF for multiple ‑ page documents. Note: The ADF scans only one side of the sheet. Use the scanner glass for single-page documents, book pages, small items(such as postcards or photos), transparencies, photo paper, or thin media(such as ma...

Initial fax setup Many countries and regions require outgoing faxes to contain the following information in a margin at the top or bottomof each transmitted page, or on the first page of the transmission: fax name (identification of the business, other entity,or individual sending the message) and f...

Choosing a fax connection Scenario 1: Standard telephone line Setup 1: Printer is connected to a dedicated fax line To connect: 1 Connect one end of the telephone cable that came with the printer to the port of the printer. 2 Connect the other end of the telephone cable to an active analog wall jack...

Setup 2: Printer is sharing the line with an answering machine Connected to the same telephone wall jack PHONE LINE To connect: 1 Connect one end of the telephone cable that came with the printer to the port of the printer. 2 Connect the other end of the telephone cable to an active analog wall jack...

Scenario 3: VoIP telephone service To connect: 1 Connect one end of the telephone cable that came with the printer to the port of the printer. 2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the VoIP adapter. Note: The port labeled Phone Line 2 or Fax Port is n...

Scenario 4: Digital telephone service through a cable provider Setup 1: Printer is connected directly to a cable modem 1 Connect one end of the telephone cable that came with your printer to the port of the printer. 2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port ...

Connecting the printer to a wall jack in Germany The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering machines. TheF port is for telephones. N F N Connect the printer to any of the N ports. PHONE LINE N F N Faxing 80

1 Connect one end of the telephone cable that came the printer to the port of the printer. 2 Connect the other end of the telephone cable to the RJ ‑ 11 adapter, and then connect the adapter to an N port. 3 If you want to connect a telephone and answering machine to the same wall jack, then connect ...

Setting the date and time You can set the date and time so that they are printed on every fax you send. If there is a power failure, then you mayhave to reset the date and time. 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address in t...

Notes: • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazineclippings) into the ADF tray. Place these items on the scanner glass. • The ADF indicator light comes on when the paper is loaded properly into the ADF tray. 2 If you are loading a docume...

• If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Fax Settings > Analog Fax Setup > Block No Name Fax . Notes: • This option blocks all incoming faxes that have a private caller ID or no fax name. • In the Banned Fax List field...

c From the Time menu, select the time you want the held faxes released. d From the Day(s) menu, select the day you want the held faxes released. 5 Click Add . Forwarding a fax This option lets you print and forward received faxes to a fax number, e ‑ mail address, FTP site, or LDSS. 1 Open a Web bro...

Scanning Scanning to an FTP address Automatic document feeder (ADF) Scanner glass Use the ADF for multiple ‑ page documents. Note: The ADF scans only one side of the sheet. Use the scanner glass for single-page documents, book pages, small items(such as postcards or photos), transparencies, photo pa...

4 Enter a shortcut number. If you enter a number that is already in use, then you are prompted to select another number. 5 Click Add . Scanning to an FTP address Scanning to an FTP address using a shortcut number 1 Load an original document faceup, short edge first into the ADF tray or facedown on t...

Understanding the printer menus Menus list Paper Menu Reports Network/Ports Security Settings Default SourcePaper Size/Type Configure MP Substitute Size Paper Texture Paper Weight Paper Loading Custom Types Custom Scan SizesUniversal Setup Menu Settings PageDevice Statistics Network Setup Page 1 Sho...

Paper menu Default Source menu Use To Default Source Tray [x]MP FeederManual PaperManual Envelope Set a default paper source for all print jobs. Notes: • Tray 1 (standard tray) is the factory default setting. • From the Paper menu, set Configure MP to “Cassette” for MP Feeder toappear as a menu sett...

Configure MP menu Use To Configure MP CassetteManualFirst Determine when the printer selects paper from the multipurpose feeder. Notes: • Cassette is the factory default setting. Cassette configures themultipurpose feeder as the automatic paper source. • Manual sets the multipurpose feeder only for ...

Paper Weight menu Use To Plain Weight LightNormalHeavy Specify the relative weight of the plain paper loaded. Note: Normal is the factory default setting. Card Stock Weight LightNormalHeavy Specify the relative weight of the card stock loaded. Note: Normal is the factory default setting. Transparenc...

Use To Colored Weight LightNormalHeavy Specify the relative weight of the colored paper loaded. Note: Normal is the factory default setting. Light Weight Light Specify that the relative weight of the paper loaded is light. Heavy Weight Heavy Specify the relative weight of the paper loaded is heavy. ...

Use To Light Loading DuplexOff Determine and set two ‑ sided printing for all print jobs that specify Light as the paper type. Heavy Loading DuplexOff Determine and set two ‑ sided printing for all print jobs that specify Heavy as the paper type. Custom [x] Loading DuplexOff Determine and set two ‑ ...

Custom Scan Sizes menu Use To Custom Scan Size [x] Scan Size NameWidthHeightOrientation PortraitLandscape 2 scans per side OffOn Specify a custom scan size name and page orientation. Notes: • The custom scan size name replaces Custom Scan Size [x] in the printermenus. • ADF Media Type is the factory...

Use To Feed Direction Short EdgeLong Edge Specify the feed direction if the paper can be loaded in either direction. Notes: • Short Edge is the factory default setting. • Long Edge appears only when the longest edge is shorter than themaximum width supported in the tray. Reports menu Reports menu Us...

Network/Ports menu Active NIC menu Use To Active NIC Auto[list of available network cards] Notes: • Auto is the factory default setting. • This menu item appears only when an optional network card is installed. Standard Network or Network [x] menu Note: Only active ports appear in this menu. All ina...

Use To Network Buffer Auto3KB to [maximum size allowed] Set the size of the network input buffer. Notes: • Auto is the factory default setting. • The value can be changed in 1KB increments. • The maximum size allowed depends on the amount of memory in the printer,the size of the other link buffers, ...

Use To Enable BOOTP OnOff Specify the BOOTP address assignment setting. Note: On is the factory default setting. Enable AutoIP YesNo Specify the Zero Configuration Networking setting. Note: Yes is the factory default setting. Enable FTP/TFTP YesNo Enable the built-in FTP server, which lets you send ...

Use To Auto Configuration OnOff Specify whether or not the wireless network adapter accepts theautomatic IPv6 address configuration entries provided by a router. Note: On is the factory default setting. View Hostname Set the host name. Note: These settings can be changed only from the Embedded Web S...

Use To View Security Mode View the encryption method for the wireless network. AppleTalk menu Note: This menu is available only in printer models connected to a wired network or when an optional network card is installed. To access the menu, navigate to any of the following: • Network/Ports > Sta...

Use To Use SSL DisabledNegotiateRequired Set the printer to use SSL for increased security when connecting to theSMTP server. Notes: • Disabled is the factory default setting. • When the Negotiate setting is used, the SMTP server determines ifSSL will be used. SMTP Server Authentication No authentic...

Use To Configure Log Enable Audit YesNo Enable Remote Syslog NoYes Remote Syslog Facility 0–23 Severity of events to log 0–7 Specify how and whether or not audit logs are created. Notes: • Enable Audit determines if events are recorded in the secure audit log andremote syslog. No is the factory defa...

Settings menu General Settings menu Use To Display Language EnglishFrancaisDeutschItalianoEspanolDanskNorskNederlandsSvenskaPortugueseSuomiRussianPolskiGreekMagyarTurkceCeskySimplified ChineseTraditional ChineseKoreanJapanese Set the language of the text appearing on the display. Note: Not all langu...

Use To Print Recovery Jam Assist OnOff Set the printer to automatically check for jammed paper. Note: On is the factory default setting. Print Recovery Page Protect OffOn Successfully print a page that may not have printed otherwise. Notes: • Off is the factory default setting. This prints a partial...

Use To Adjust ADF Skew AutoOffOn Correct slight skew in the scanned image. Note: Auto is the factory default setting. Scan edge to edge OffOn Specify if the original document is scanned edge ‑ to ‑ edge. Note: Off is the factory default setting. Sharpness 1–5 Adjust the amount of sharpness of a copy...

Use To Caller ID OffPrimaryAlternate Specify the type of caller ID being used. Fax Number Masking OffFrom leftFrom right Specify the direction from where digits are masked in an outgoing fax number. Notes: • Off is the factory default setting. • The “Digits to mask” setting determines the number of ...

Use To Auto Convert Color Faxes to MonoFaxes OnOff Convert all outgoing faxes to black and white. Note: On is the factory default setting. Fax Receive Settings Use To Enable Fax Receive OnOff Allow the printer to receive fax jobs. Note: On is the factory default setting. Enable Caller ID OnOff Allow...

Use To Fax Footer OnOff Print the transmission information at the bottom of each page from a received fax. Note: Off is the factory default setting. Max Speed 2400480096001440033600 Specify the maximum speed in baud at which faxes are received. Note: 33600 is the factory default setting. Fax Forward...

E ‑ mail Settings menu Use To E ‑ mail Server Setup Send me a copy Never appearsOn by defaultOff by defaultAlways On Send a copy of the e-mail to the sender. Note: “Never appears” is the factory default setting. E ‑ mail Server Setup Max E ‑ mail size 0–65535 KB Specify the maximum e-mail size in ki...

Use To Mirror Image OffOn Create a mirror image of the original document. Note: Off is the factory default setting. Negative Image OffOn Create a negative image of the original document. Note: Off is the factory default setting. Shadow Detail ‑ 4 to 4 Adjust the amount of shadow detail visible on a ...

Print Settings Setup menu Use To Printer Language PCL EmulationPS Emulation Set the default printer language. Notes: • PCL Emulation is the factory default printer language. • Setting a printer language as the default does not prevent asoftware program from sending print jobs that use anotherprinter...

Use To Paper Saver Ordering HorizontalReverse HorizontalReverse VerticalVertical Specify the order in which pages are printed on a single sheet when using Paper Saver. Notes: • Horizontal is the factory default setting. • Positioning depends on the number of pages and whether they are in portraitor ...

Use To Enhance Fine Lines OnOff Enable a print mode preferable for files such as architectural drawings, maps, electricalcircuit diagrams, and flow charts. Notes: • Off is the factory default setting. • You can set this option from the printer software. For Windows users, click File > Print , and...

HTML menu Use To Font Name Albertus MTAntique OliveApple ChanceryArial MTAvant GardeBodoniBookmanChicagoClarendonCooper BlackCopperplateCoronetCourierEurostileGaramondGenevaGill SansGoudyHelveticaHoefler TextIntl CG TimesIntl CourierIntl Univers Joanna MTLetter GothicLubalin GraphMarigoldMonaLisa Re...

Use To Margin Size 8–255 mm Set the page margin for HTML documents. Notes: • 19 mm is the factory default setting. • Margin size can be increased in 1 ‑ mm increments. Backgrounds Do Not PrintPrint Specify whether to print backgrounds on HTML documents. Note: Print is the factory default setting. Im...

Saving money and the environment Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impacton the environment. We design with the environment in mind, engineer our packaging to reduce materials, and providecollection and recycling programs. ...

Check your first draft for accuracy Before printing or making multiple copies of a document: • Use the preview feature to see how the document looks like before you print it. • Print one copy of the document to check its content and format for accuracy. Avoid paper jams Correctly set the paper type ...

Use To On Reduce printer noise. Notes: • Print jobs process at a reduced speed. • Printer engine motors do not start until a documentis ready to print. There is a short delay before thefirst page is printed. • The alarm control and cartridge alarm sounds areturned off. • The printer ignores the Adva...

Using Hibernate mode Hibernate is an ultra ‑ low ‑ power saving mode. Notes: • Three days is the default amount of time before the printer enters Hibernate mode. • Make sure to wake the printer from Hibernate mode before sending a print job. A hard reset or a long press ofthe Sleep button wakes the ...

4 From the Time menu, select the time. 5 From the Day(s) menu, select the day or days. 6 Click Add . Recycling Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information,see: • The Notices chapter • The Environmental Sustainability section of t...

Securing the printer Statement of Volatility Your printer contains various types of memory that can store device and network settings, and user data. Type of memory Description Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print j...

The printer will perform a power ‑ on reset, and then return to normal operating mode. Finding printer security information In high-security environments, it may be necessary to take additional steps to make sure that confidential data storedin the printer cannot be accessed by unauthorized persons....

Maintaining the printer Cleaning printer parts Cleaning the printer Note: You may need to perform this task after every few months. Warning—Potential Damage: Damage to the printer caused by improper handling is not covered by the printer warranty. 1 Make sure that the printer is turned off and unplu...

Cleaning the scanner glass Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images. 1 Slightly dampen a soft, lint-free cloth or paper towel with water. 2 Open the scanner cover. 3 Clean all the areas shown, and then let them dry. 1 White undersid...

Checking the status of parts and supplies A message appears on the display when a replacement supply item is needed or when maintenance is required. Checking the status of parts and supplies on the printer control panel From the printer control panel, navigate to: > Status/Supplies > > View...

Ordering supplies To order parts and supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorizedsupplies dealers in your area. In other countries or regions, go to www.lexmark.com or contact the place where you purchased the printer. The Lexmark Return Program le...

Maintenance kit Part number 100 ‑ V maintenance kit * 40X9146 110 ‑ V maintenance kit 40X9135 220 ‑ V maintenance kit 40X9136 * This is available only in Japan. Ordering an ADF separator pad Order an ADF separator pad when the ADF fails to pick paper or picks more than one sheet of paper at a time. ...

Replacing supplies Replacing the toner cartridge 1 Press the button on the right side of the printer, and then open the front door. 2 Pull the toner cartridge out using the handle. 3 Unpack the toner cartridge, and then remove all packing materials. 4 Shake the new cartridge to redistribute the tone...

5 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side railsinside the printer. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to light may cause print quality problem...

Moving the printer CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more trained personnel to lift it safely. Before moving the printer CAUTION—POTENTIAL INJURY: Before moving the printer, follow these guidelines to avoid personal injury or printer damag...

Managing the printer Finding advanced networking and administrator information This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced systemsupport tasks, see the Networking Guide on the Software CD or the Embedded Web Server Administrator's Guide at ...

Viewing reports You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of theprinter, network, and supplies. 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address in the TCP/IP section ...

Notification Description Non Continuable Stop 1,2 The printer stops processing jobs when the supply condition is reached. The supply must bereplaced to continue printing. 1 The printer generates an e-mail about the status of the supply when supply notification is enabled. 2 The printer stops when so...

Clearing jams By carefully selecting paper and specialty media and loading it properly, you should be able to avoid most jams. If jamsoccur, then follow the steps outlined in this chapter. Warning—Potential Damage: Never use any tool to remove a jam. Doing so could permanently damage the fuser. Avoi...

• Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not pressing tightlyagainst the paper or envelopes. • Push the tray firmly into the printer after loading paper. Use recommended paper • Use only recommended paper or specialty media. • Do not load wrinkled...

Troubleshooting Understanding the printer messages Cartridge low [88.xy] You may need to order a toner cartridge. If necessary, select Continue on the printer control panel to clear the message and continue printing. For non ‑ touch ‑ screen printer models, press to confirm. Cartridge nearly low [88...

Defective flash detected [51] Try one or more of the following: • Replace the defective flash memory card. • From the printer control panel, select Continue to ignore the message and continue printing. For non ‑ touch ‑ screen printer models, press to confirm. • Cancel the current print job. Error r...

Fax Station Number not set up. Contact system administrator. Try either of the following: • From the printer control panel, select Continue to clear the message. For non ‑ touch ‑ screen printer models, press to confirm. • Complete the Analog Fax Setup. If the message appears again after completing ...

• Update the network firmware in the printer or print server. For more information, visit the Lexmark support Website at http://support.lexmark.com . No analog phone line connected to modem, fax is disabled. Connect the printer to an analog phone line. Non ‑ Lexmark [supply type], see User’s Guide [...

For more information, visit http://support.lexmark.com or contact customer support. Reinstall missing or unresponsive cartridge [31.xy] Try one or more of the following: • Check if the toner cartridge is missing. If missing, install the toner cartridge. For information on installing the cartridge, s...

Note: If you do not have a replacement cartridge, then see the “Ordering supplies” section of the User’s Guide or visit www.lexmark.com . Replace cartridge, printer region mismatch [42.xy] Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer r...

Replace jammed originals if restarting job. From the printer control panel, try one or more of the following: • Select Cancel job to clear the message and cancel the scan job. For non ‑ touch ‑ screen printer models, press to confirm. • Select Scan from automatic feeder to continue scanning from the...

Scanner disabled. Contact system administrator if problem persists. [840.02] From the printer control panel, try one or more of the following: • Select Continue with scanner disabled to return to the home screen, and then contact your system support person. • Select Reboot and automatically enable s...

Standard USB port disabled [56] From the printer control panel, select Continue to clear the message. For non ‑ touch ‑ screen printer models, press to confirm. Notes: • The printer discards any data received through the USB port. • Make sure the USB Buffer menu is not set to Disabled. Supply needed...

Weblink server not set up. Contact system administrator. Select Continue to clear the message. For non ‑ touch ‑ screen printer models, press to confirm. Note: If the message appears again, then contact your system support person. Solving printer problems • “Basic printer problems” on page 190 • “Ha...

Printer display is blank Action Yes No Step 1 Press the Sleep button on the printer control panel. Does Ready appear on the printer display? The problem is solved. Go to step 2. Step 2 Turn off the printer, then wait for about 10 seconds, and then turn theprinter back on. Do Please wait and Ready ap...

Action Yes No Step 4 a Check if the internal option is selected. It may be necessary to manually add the internal option in the printerdriver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 23 . b Resend the print job. Does the in...

Paper feed problems Jammed pages are not reprinted Action Yes No a Turn on jam recovery. 1 From the printer control panel, navigate to: Settings > General Settings > Print Recovery > Jam Recovery 2 Select On or Auto . 3 Depending on your printer model, press or touch Submit . b Resend the p...

Paper jam message remains after jam is cleared Action Yes No a Do either of the following: • For touch ‑ screen printer models, touch or Done . • For non ‑ touch ‑ screen printer models, select Next > > Clear the jam, press OK > . b Follow the instructions on the printer display. Does the p...

Action Yes No Step 2 a From the Paper menu on the printer control panel, set the paper sizeand type to match the paper loaded in the tray. b Resend the print job. Did the job print from the correct tray or on the correct paper? The problem is solved. Go to step 3. Step 3 a Depending on your operatin...

Multiple ‑ language PDF files do not print Action Yes No Step 1 a Check if the print options for the PDF output are set to embed all fonts. For more information, see the documentation that came with AdobeAcrobat. b Generate a new PDF file, and then resend the print job. Do the files print? The probl...

Action Yes No Step 4 a Check if the ports (USB, serial, or Ethernet) are working and if thecables are securely connected to the computer and the printer. Note: For more information, see the setup documentation that came with the printer. b Resend the print job. Do the jobs print? The problem is solv...

Action Yes No Step 3 a Remove held jobs stored in the printer memory. b Resend the print job. Did the job print? The problem is solved. Go to step 4. Step 4 a Disable the Page Protect feature. From the printer control panel, navigate to: Settings > General Settings > Print Recovery > Page P...

Tray linking does not work Notes: • The trays can detect paper length. • The multipurpose feeder does not automatically detect the paper size. You must set the size from the PaperSize/Type menu. Action Yes No Step 1 a Open the trays, and then check if they contain paper of the same sizeand type. • C...

Print quality problems Characters have jagged or uneven edges Action Yes No Step 1 a Print a font sample list to check if the fonts you are using are supportedby the printer. 1 From the printer control panel, navigate to: Menus > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts . b...

Action Yes No Step 2 From the printer control panel, set the paper size and type in the Papermenu to match the paper loaded in the tray. Do the paper size and type match the paper loaded in the tray? Go to step 3. Do one or more of thefollowing: • Specify the papersize from the traysettings to match...

Action Yes No Step 2 a Replace the fuser. For more information on installing the fuser, seethe instruction sheet that came with the part. b Resend the print job. Do compressed images still appear? The problem is solved. Contact customer support . Gray background on prints ABCDE ABCDE ABCDE Leading e...

Horizontal voids appear on prints Leading edge Trailing edge Action Yes No Step 1 a Make sure your software program is using a correct fill pattern. b Resend the print job. Do horizontal voids appear on prints? Go to step 2. The problem is solved. Step 2 a Load the specified tray or feeder with a re...

Incorrect margins on prints A B C D A B C D A B C D Action Yes No Step 1 a Move the width and length guides in the tray to the correct positionsfor the paper size loaded. b Resend the print job. Are the margins correct? The problem is solved. Go to step 2. Step 2 From the printer control panel, set ...

Paper curl Action Yes No Step 1 Move the width and length guides in the tray to the correct positions forthe size of the paper loaded. Are the width and length guides positioned correctly? Go to step 2. Adjust the width andlength guides. Step 2 From the printer control panel, set the paper type and ...

Print is too dark Action Yes No Step 1 a From the Quality menu on the printer control panel, reduce the tonerdarkness. Note: 8 is the factory default setting. b Resend the print job. Is the print still too dark? Go to step 2. The problem is solved. Step 2 a From the printer control panel, set the pa...

Action Yes No Step 5 a Load paper from a fresh package. Note: Paper absorbs moisture due to high humidity. Store paper in its original wrapper until you use it. b Resend the print job. Is the print still too dark? Go to step 6. The problem is solved. Step 6 Replace the imaging unit, and then resend ...

Action Yes No Step 4 Make sure that the paper has no texture or rough finishes. Are you printing on textured or rough paper? From the printercontrol panel, changethe texture settings inthe Paper Texturemenu to match thepaper you are printingon. Go to step 5. Step 5 a Load paper from a fresh package....

Action Yes No Step 1 a Check if there is packing material left on the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imagingunit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more tha...

Action Yes No Step 1 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print quality problems. 2 Install the imaging unit, and t...

Shadow images appear on prints A B C DA B C D A B C DA B C D Leading edge Trailing edge Action Yes No Step 1 Load paper with the correct paper type and weight in the tray. Is paper with the correct paper type and weight loaded in the tray? Go to step 2. Load paper with thecorrect paper type andweigh...

Action Yes No Step 1 a Move the width and length guides in the tray to the correct positionsfor the size of the paper loaded. b Resend the print job. Is the print still skewed? Go to step 2. The problem is solved. Step 2 a Check if you are printing on a paper that is supported by the tray. b Resend ...

Action Yes No Step 4 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print quality problems. 2 Install the imaging unit, and t...

Action Yes No Step 3 a Load paper from a fresh package. Note: Paper absorbs moisture due to high humidity. Store paper in its original wrapper until you use it. b Resend the print job. Do streaked vertical lines appear on prints? Go to step 4. The problem is solved. Step 4 a Reinstall the imaging un...

Toner rubs off Leading edge Trailing edge ABC DEF Action Yes No Step 1 From the Paper menu on the printer control panel, check the paper type,texture, and weight. Do the paper type, texture, and weight match the paper loaded in thetray? Go to step 2. Specify the paper type,texture, and weightfrom th...

Uneven print density Action Yes No Replace the imaging unit, and then resend the print job. Is the print density uneven? Contact customer support . The problem is solved. Vertical voids appear on prints Leading edge Trailing edge Action Yes No Step 1 a Make sure your software program is using a corr...

Action Yes No Step 4 a Redistribute the toner in the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print qu...

Scanner unit does not close Action Yes No Check if there are no obstructions between the scanner unit and theprinter. a Lift the scanner unit. b Remove any obstruction that keeps the scanner unit open. c Lower the scanner unit. Did the scanner unit close properly? The problem is solved. Contact cust...

Action Yes No Step 6 Check the copy settings. From the Copy screen, check if the Content Type and Content Sourcesettings are correct for the document being scanned. Are the Content Type and Content Source settings correct for thedocument being scanned? Go to step 7. Change the ContentType and Conten...

Action Yes No Step 2 Check if the paper size setting matches the size of the paper loaded in thetray. From the Paper menu on the printer control panel, check the PaperSize setting. Does the paper size setting match the size of the paper loaded in the tray. Go to step 3. Change the paper sizesetting ...

Action Yes No a From the printer control panel, navigate to: > Settings > > General Settings > > Run initial setup > > b Turn off the printer, and then turn it back on. The “Select your language” screen appears on the printer display. c Select a language, and then press . d Sele...

Cannot send or receive a fax Action Yes No Step 1 Check if an error or status message appears on the display. Is there an error or status message on the display? Clear the error or statusmessage. Go to step 2. Step 2 Check if the power cord is plugged into the printer and a properlygrounded electric...

Action Yes No Step 10 a Temporarily disable voice mail service. For more information, contactyour telephone company. Note: If you want to use both voice mail and the printer, then consider adding a second telephone line for the printer. b Try sending or receiving a fax. Can you send or receive a fax...

Action Yes No Step 3 Replace the toner cartridge. For more information, see the instructionsheet that came with the supply. Can you receive faxes? The problem is solved. Contact customer support . Can receive but not send faxes Action Yes No Step 1 Check if the printer is in Fax mode. From the print...

Received fax has poor print quality Action Yes No Step 1 Ask the person who sent you the fax to: a Check if the quality of the original document is satisfactory. b Increase the fax scan resolution, if possible. c Resend the fax. There may have been a problem with the quality ofthe telephone line con...

• “Scanning takes too long or freezes the computer” on page 230 • “Poor scanned image quality” on page 231 • “Partial document or photo scans” on page 232 The scanner does not respond Action Yes No Step 1 Check if the printer is turned on. Is the printer turned on? Go to step 2. Turn on the printer....

Scan job was not successful Action Yes No Step 1 Check the cable connections. Make sure the Ethernet or USB cable is securely connected to thecomputer and the printer. Are the cables securely connected? Go to step 2. Connect the cablesproperly. Step 2 Check if the file name is already in use. Is the...

Action Yes No Step 2 Select a lower scan resolution. Does scanning still take too long or freeze the computer? Contact customer support . The problem is solved. Poor scanned image quality Action Yes No Step 1 Check if an error message appears on the display. Is there an error message on the printer ...

Action Yes No Step 7 Increase the scan resolution settings for a higher ‑ quality output. Did the increased resolution produce a higher ‑ quality output? Problem solved. Contact customer support . Partial document or photo scans Action Yes No Check the placement of the document or photo. Make sure t...

Action Yes No Step 3 Check if the network is working. a Print a network setup page. b Check the first section of the network setup page and confirm that thestatus is Connected. Note: If the status is Not Connected, then the connection may be intermittent, or the network cable may be defective. Conta...

Notices Product information Product name: Lexmark XM1135 Machine type: 7015 Model(s): 279 Edition notice March 2014 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARR...

Stempel Garamond Linotype-Hell AG and/or its subsidiaries Taffy Agfa Corporation Times New Roman The Monotype Corporation plc Univers Linotype-Hell AG and/or its subsidiaries All other trademarks are the property of their respective owners. AirPrint and the AirPrint logo are trademarks of Apple, Inc...

1-meter average sound pressure, dBA Printing 52 Scanning 45 Copying 54 Ready N/A Values are subject to change. See www.lexmark.com for current values. Temperature information Ambient operating temperature 15.6 to 32.2°C (60 to 90°F) Shipping temperature -40 to 43.3°C (-40 to 110°F) Storage temperatu...

DANGER - Invisible laser radiation when cartridges are removed and interlock defeated. Avoid exposure to laser beam.PERIGO - Radiação a laser invisível será liberada se os cartuchos forem removidos e o lacre rompido. Evite a exposição aos feixes de laser. Opasnost - Nevidljivo lasersko zra č enje ka...

Sleep Mode This product is designed with an energy-saving mode called Sleep Mode . The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this productis not used for a specified period of time, called the Sleep M...

日本の VCCI 規定 製品にこのマークが表示されている場合、次の要件を満たしています。 この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをしてください。 VCCI-B European Community (EC) directives conformity This product is in conformity with the protection requirements of EC Council d...

connected to a line, as determined by the total RENs, contact your local telephone company. For products approvedafter July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX.The digits represented by ## are the REN without a decimal point (for e...

the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electricalsurges. This equipment uses CA11A telephone jacks. Avis réservé aux utilisateurs du réseau téléphonique du Canada Ce produit est conforme aux spécifications techniques d’Industri...

Compliance is indicated by the CE marking. The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA.The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, MillenniumTower III, 1095 Budapest H...

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away fromwindows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject tolicensing. The installer of this radio equipment must ensure that the a...

Notice to users in the European Union This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC,1999/5/EC, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member Statesrelating to electromagnetic compatibilit...

Patent acknowledgment The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual PropertyRights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for TransportLayer Security (TLS) implemented in the p...

—Use of printing media outside of Lexmark specifications —Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts —Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark TO THE EXTENT PERMITTED BY APP...

Index Numerics 250 ‑ sheet tray installing 19 550 ‑ sheet tray installing 19 Symbols [x] ‑ page jam, clear manual feeder. [25y.xx] 173[x] ‑ page jam, clear standard bin. [20y.xx] 170[x] ‑ page jam, open automatic feeder top cover. [28y.xx] 175[x] ‑ page jam, open front door. [20y.xx] 166[x] ‑ page j...