Kyocera FS-1010 - Manuals

• Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it is dirty, clean it to remove the risk of fire or electric shock. ............................................................ • Never attempt to disassemble the optical unit in machines using laser...

Chapter 1 Contents 1-1 Printer specifications ...................................................................................................................... 1-3 1-1-1 Specifications .................................................................................................................

FS-1010 1-3 1-1 Printer specifications 1-1-1 Specifications (1) Engine Item Specification Print method Print speed (when printing multiple pages) Resolution (dpi) Smoothing First print (A4 or letter, 23 ° C), depends on input data Warm-up time at 23 ° C Maximum duty cycle (A4) Process unit life expe...

FS-1010 1-7 1-3 Safety information 1-3-1 Safety information (1) Laser safety This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to Radiation Control for Health and Safety Act of 1968. This means ...

1-8 FS-1010 WARNING Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Figure 1-3-1 Caution labels Label on the scanner unit (Inside the printer) Label on the left cover rear side Label on the fuser unit European ...

FS-1010 1-9 (4) CDRH regulations (U.S.A.) The Center of Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured after August 1, 1976. Compliance is mandatory f...

1-10 FS-1010 1-4 Environmental requirements 1-4-1 Environmental conditions The Environmental requirements section on page 1-5 should be observed to ensure the optimum operation of the printer. The use of the printer in a location which does not satisfy the requirements may result in troubles and ris...

1-14 FS-1010 1 1-5 About the toner container 1-5-1 Toner container The printer should use a TK-17 toner kit. To ensure the high print quality and long service life, the following handling precautions should apply. CAUTION As the Ecosys printers are designed to ensure the optimum print quality when u...

FS-1010 1-15 (2) Toner container storage The toner contained in the container is susceptible to temperature and humidity. To ensure the high print quality, store the toner container in a place that satisfies the following environmental conditions: Temperature: -20 to 40 ° C (-4 to 104 ° F) Humidity:...

Chapter 2 I n s t a l l a t i o n / O p e r a t i o n

Chapter 2 Contents 2-1 Unpacking ......................................................................................................................................... 2-3 2-1-1 Unpacking and inspection .................................................................................................

2-4 FS-1010 2-2 Installing the printer Installing the printer requires several steps. Proceed as follows in sequence. If the option paper feeder is used with the printer, begin installation with connecting the printer and the paper feeder. For details, refer to the optional Paper feeder’s Service Ma...

FS-1010 2-5 3. Take the toner container 2 from the bag. Hold it with the protective seal 3 (orange-colored) facing up. Shake the toner container 2 horizontally at least five times. This ensures that the toner is evenly distributed inside. Figure 2-2-2 Shaking the toner container 4. Carefully remove ...

2-6 FS-1010 5. Install the toner container 2 into the printer. 6. Push firmly on the top of the toner container 2 at the positions marked [PUSH HERE]. Figure 2-2-4 Installing the toner container 2

FS-1010 2-7 7. Push the lock lever #1 1 to the lock position. 8. Close the top cover 4 . Figure- 2-2-5 Locking the toner container NOTE The printer is shipped from the factory with no toner supplied in its developer (Process unit). When the printer is first switched on after the toner container is i...

2-8 FS-1010 2-2-2 Expanding memory The FS-1010 printer comes standard equipped with 16 MB of main memory on the main board. Printer memory can be expanded to up to the maximum 144 MB (16 + 128 MB). (1) Minimum memory requirements Refer to the table below for minimum memory requirements in various en...

2-10 FS-1010 (4) Installing the DIMM The main board of the printer is equipped with one socket for memory expansion. Expansion memory is available in the form of DIMM (Dual In-line Memory Module). CAUTION Take precautions that no foreign substances such as metal chips or liquid get inside the printe...

2-12 FS-1010 (6) Installing the memory card (CompactFlash) The main board of the printer is equipped with one slot for memory card. CAUTION Take precautions that no foreign substances such as metal chips or liquid get inside the printer during the installation process. Operation of the printer durin...

FS-1010 2-13 Insert the memory card 4 in the slot. Insert as shown in the figure. Push it in all the way. Close and secure the option interface slot cover (or network interface card or the serial Interface board) . Figure 2-2-10 installing the memory card 4

2-14 FS-1010 (7) Installing the network interface card If the serial interface board kit is installed, remove it to use the network interface card. CAUTION Take precautions that no foreign substances such as metal chips or liquid get inside the printer during the installation process. Operation of t...

FS-1010 2-15 2-3 Using the operator panel This section provides explanation on how to use the printer’s operator panel for basic operation. For details, refer to the printer’s User’s Manual . 2-3-1 Operator panel The printer’s operation panel has the following LED indicators and keys. Note that adju...

2-16 FS-1010 2-3-2 Remote operation panel The remote operation panel is a utility that allows you to make basic printer settings from the computer connected to the printer or the network. For details on installation and usage, see the printer’s User’s Manual contained as an electronic file in the CD...

Chapter 3 Contents 3-1 Maintenance/Adjustments .............................................................................................................. 3-3 3-1-1 Life expectancy of modules ....................................................................................................... 3...

3-5 FS-1010 (3) Toner container replacement To replace the toner container, open the top cover. Pull lock lever #1 1 to the release [UNLOCK] position, then pull lock lever #2 2 to the release (right) position. Figure 3-1-1 Releasing Lock levers #1 and #2 Gently remove the old toner container 3 . Fig...

3-6 FS-1010 Put it in the supplied plastic bag 4 and dispose of it. Figure 3-1-3 Disposal of the old toner container NOTE Although the toner container is made from non-harmful, flammable material, be sure to dispose of it according to laws and regulations. Proceed with the instructions provided in c...

3-7 FS-1010 3-1-3 Cleaning the printer To avoid print quality problems, the following printer parts must be cleaned with every toner container replacement. To clean the printer, first, remove the process unit from the printer. Open the top cover 1 and front cover 2 . Lift the process unit 3 together...

3-8 FS-1010 (1) Cleaning the registration roller Use the supplied wiper cloth 1 to clean dust and dirt away from the registration roller 2 (metal). Figure 3-1-5 Cleaning the registration roller (2) Cleaning the main charger wire Slide the charger cleaner knob (green colored) back and forth 2 to 3 ti...

3-9 FS-1010 3-1-4 Updating the firmware Updating the system (controller) firmware is possible by downloading the firmware through the parallel interface or through the memory card (CompactFlash). These firmware programs are directly overwritten in the system DIMM [board KP-893] (Flash ROM type only)...

3-10 FS-1010 (2) Downloading the firmware from the parallel interface This section explains how to download firmware data from the parallel interface. The printer system can automatically recognize whether the data to be overwritten is for controller firmware. CAUTION Downloading the firmware takes ...

3-11 FS-1010 (3) Downloading the firmware from the memory card To download data written in a memory card (CompactFlash) to the printer, proceed as explained in this section. CAUTION Downloading firmware takes several minutes. Do not turn power off during downloading. If downloading is interrupted by...

3-12 FS-1010 Cause Corrective action Description LED indicators LED indicators Download finished normally Convention Download errors Slow flashing Fast flashing Lit Off Red Green Meaning Download data error Deficit of a file header Deficit of a data header File checksum error File header version err...

Chapter 4 Contents 4-1 Electrophotographic system .......................................................................................................... 4-3 4-1-1 Electrophotographic cycle ......................................................................................................... 4...

4-3 FS-1010 4-1 Electrophotographic system Electrophotography is the technology used in laser printing which transfer data representing texts or graphics objects into a visible image which is developed on the photosensitive drum, finally fusing on paper, using light beam generated by a laser diode. ...

4-4 FS-1010 1 Main charger unit 2 Charger wire 3 Grid 4 Developing roller 5 Gear Z14-Z18 6 Gear Z14-Z36 7 Gear Z18-Z36 8 Free gear Z40 Process unit mechanism Figure 4-1-2 Process unit mechanism 9 Gear Z18-Z35H 0 MAG gear Z24H ! Mixer gear Z20 B @ Mixer gear Z20 A # DLP screw B $ DLP screw A % Drum ^...

4-5 FS-1010 (1) Main charging Photo conductive drum The durable layer of organic photoconductor (OPC) is coated over the aluminum cylinder base. The OPC tend to reduce its own electrical conductance when exposed to light. After a cyclic process of charging, exposure, and development, the electrostat...

4-6 FS-1010 Charging the drum The following shows a simplified diagram of the electrophotographic components in relation to the engine system. Charging the drum is done by the main charger unit A . Figure 4-1-4 Charging the drum As the drum C rotates in a “clean (neutral)” state, its photoconductive...

4-8 FS-1010 Laser scanner unit Name Description 1 Laser diode Emits diffused, visible laser. 2 Cylindrical lens Compensates the vertical angle at which the laser beam hits a polygon mirror segment. 3 Polygon mirror (motor) Has six mirror segments around its hexagonal circumference; each mirror corre...

4-9 FS-1010 Drum surface potential The laser beam is continually switched on and off depending on the print data. It is on for a black (exposed) dot and off for a white (blank) dot. Since the drum surface is evenly charged, whenever it is illuminated by the laser beam, the electrical resistance of t...

4-13 FS-1010 1 Heat roller 2 Idle gear Z34 3 Exit gear Z23 4 Idle gear Z18 0 ! 1 2 3 4 5 6 7 8 9 @ 5 Heat gear Z33 6 Press roller 7 Heater lamp [500 ± 25 W] 8 Thermal cutout 9 Separator(s) 0 Thermistor ! Exit pulley(s) @ Lower exit roller Fuser unit mechanism Figure 4-1-11 Fuser unit mechanism

4-14 FS-1010 E A B C D (6) Cleaning After the transferring process, the drum needs to be physically cleaned of toner which is residual after the development process. The cleaning blade A is constantly pressed against the drum B and scrapes the residual toner off to the sweep roller C . The waste ton...

4-15 FS-1010 4-2 Paper feeding system The paper feeding system picks up paper from the cassette, MP tray, or if installed, the paper feeder PF-17, feeds it in the printer, and delivers in the output tray. Paper is fed at the precise timing in synchronization with data processing. The paper feeding s...

4-16 FS-1010 4-2-1 Paper feed control The following diagram shows interconnectivity of the feeding system components including the sensors and rollers. The engine board provides the signals in conjunction with the electrophotography process that is driven by the main board. Figure 4-2-2 Paper feed c...

4-17 FS-1010 0 ! @ % ( & A B # $ * ) ^ 3 4 5 6 2 1 7 8 9 C A For process unit; drum (From main unit) B For process unit; toner container, developing roller etc. (From main unit) C From process unit; drum (To transfer roller) Driving power train 1 Main motor (gear) 2 Registration clutch 3 MP feed...

4-18 FS-1010 4-3 Electrical control system 4-3-1 Electrical parts layout Figure 4-3-1 Electrical parts layout 9 2 08 ML 5 ! # K J 4 % $ @ 7 H 3 G I 1 6 2 B A C D E F ( & ^ * 1 Main board (KP-888) 2 Engine board (KP-882) A Go key (switch) B Cancel key (switch) C Toner indicator (LED) D Paper empt...

4-19 FS-1010 4-3-2 Operation of circuit boards (1) Main board Figure 4-3-2 Main board circuit block diagram Q01Digital Transistor Q02Digital Transistor YC03 USB I/F USBINT USBDN EDB31-16 EBIU Data bus EBIU Address bus VBUL USBDP EBA22, EBA10-1 CDWAITN, CDET1-2 CDRST EBCSN2, EBCSN3EBOEN1, EBWEN1 YC08...

4-20 FS-1010 (2) Engine board Figure 4-3-3 Engine board circuit block diagram Main board (KP-888) Laser scanner unit RSTIN RSTN PLGCLK PLGRDYN PLGDRN EESCK MPFDRN EEDIO MP feed clutch Eraser lamp Eraser lamp control circuit RESDRN Registration clutch Feed clutch MOTORN MRDYN PFMDRN FEDDRN Bias board...

4-21 FS-1010 Eraser lamp control circuit The CPU (U01) turns pin #23 (ERASERN) of U01 to H level, transistors (Q16 and Q14) turns on consequently, and the 24 V DC given at pin #1 of connector YC05 applies to the eraser lamps. The eraser lamps thus illuminate as the current flows through the eraser l...

4-25 FS-1010 Polygon motor control circuit The main controller board supplies the 1700.8 Hz clock pulse (PLGCLK) via the engine board to the PLL control IC (IC1) for the polygon motor. To begin printing, the engine CPU U01 turns PLGDR to H level, the PLL control IC (IC1) starts to revolve the polygo...

4-26 FS-1010 (3) Power supply board The power supply board provides the AC power input and DC power and outputs. The high voltage bias generator circuit is mounted on a separate board. A simplified schematic diagram is shown below. Figure 4-3-8 Power supply board circuit block diagram FET(Q1) Switch...

4-27 FS-1010 (4) Bias board The bias board contains the developing bias output circuit, registration sensor, paper empty sensor, and the cassette switch. It also provides a liaison connection to the high voltage board, power supply, and the toner sensor. Figure 4-3-9 Bias board circuit block diagram...

4-28 FS-1010 (5) High voltage board The high voltage board contains the high voltage output circuit, interlock switch circuit as well as providing a liaison connection with the power supply board, bias board, and the engine board. Figure 4-3-10 High voltage board circuit block diagram Controlanddriv...

4-29 FS-1010 Interlock switch The interlock switch is located on the high voltage board and opened and closed in conjunction with the front cover or the top cover via the interlock lever. This switch connects and disconnects the +24 V DC power supply line. If the front cover or the top cover is open...

Chapter 5 Contents 5-1 General instructions ........................................................................................................................ 5-3 5-1-1 Screw/hardware .................................................................................................................

FS-1010 5-3 5-1 General instructions This chapter provides procedures for removal and replacement of the field replacement components. For other components not explained in this chapter, the diagrams in the Parts Catalog attached with this manual will help locate the component. When replacing of a c...

FS-1010 5-4 5-2 Disassembly Before proceeding, remove the paper cassette and the optional paper feeder, if installed. 5-2-1 Removing the process unit 1. Open the top cover 1 . 2. Open the front cover 2 . 3. Lift the process unit 3 together with the toner container out of the printer. Figure 5-2-1 Re...

FS-1010 5-5 5-2-2 Removing the principal outer covers (1) Removing the top cover/face-down output tray 1. Open the top cover 1 . 2. Remove two screws 2 . 3. Remove the top cover/face-down output tray 3 . Figure 5-2-2 Removing the top cover/face-down output tray 2 3 1

FS-1010 5-7 5-2-3 Removing the feed roller CAUTION When refit the feed roller, fit the D-cut shaft into the D-shape hole of the feed roller. 1. Remove the paper cassette and the process unit. (See page 5-4) 2. Stand the machine the front side up. 3. Move the feed roller in the direction A , and remo...

FS-1010 5-10 5-2-5 Removing the transfer roller CAUTION Do not touch the transfer roller (sponge) surface. Oil and dust (particles of paper, etc.) on the transfer roller can significantly deteriorate the print quality (white spots, etc.). When refitting the bushes and springs, make sure to refit the...

FS-1010 5-11 5-2-6 Removing the principal circuit boards (1) Removing the engine board 1. Remove the top cover/face-down output tray and right cover (See pages 5-5 and 5-6). 2. Remove all (ten) connectors from the engine board 1 . 3. Remove three screws 2 . 4. Remove the engine board 1 . Figure 5-2-...

FS-1010 5-14 (3) Removing the power supply board and high voltage board 1. Remove the process unit (See page 5-4). 2. Remove the top cover/face-down output tray and left cover (See pages 5-5 and 5-6). 3. Remove three connectors 1 from the power supply board 2 . 4. Remove eight screws 3 . 5. Remove t...

FS-1010 5-16 5-2-7 Removing the main motor and drive unit 1. Remove the cassette and process unit (See page 5-4). 2. Remove the top cover/face-down output tray and right cover (See pages 5-5 and 5-6). 3. Remove three connectors 1 from the main motor 2 . 4. Remove four screws 3 . 5. Remove main motor...

FS-1010 5-20 5-2-8 Removing and splitting the fuser unit WARNING The fuser unit is hot after the printer was running. Wait until it cools down. CAUTION When refitting the fuser unit, make sure the fuser unit gear and the printer’s drive gear are properly meshed with each other. For this, rotate the ...

FS-1010 5-22 (1) Removing the separators WARNING The separation claws are extremely hot immediately after the printer was running. Allow substantial period of time until it cools down. 1. Remove and split the fuser unit (See page 5-20). 2. Loosen the stopper screws 1 . 3. Hold the separators 2 uprig...

FS-1010 5-24 (3) Removing the heat roller WARNING The heat roller is extremely hot immediately after the printer was running. Allow substantial period of time until it cools down. 1. Remove and split the fuser unit (See page 5-20). 2. Remove the heater lamp (See previous page). 3. Press the lamp A h...

FS-1010 5-27 (5) Removing the thermal cutout CAUTION Do not bend the terminals of the thermal cutout. 1. Remove and split the fuser unit (See page 5-20). 2. Remove the heater lamp (See page 5-23). 3. Remove the heat roller (See page 5-24). 4. Remove the two screws 1 . 5. Remove the thermal cutout 2 ...

FS-1010 5-29 5-2-9 Removing the laser scanner unit and the eraser lamp 1. Remove the process unit (See page 5-4). 2. Remove the top cover/face-down output tray, right cover, and the left cover (See pages 5-5 and 5-6). 3. Remove four connectors 1 . 4. Remove five screws 2 and four screws 3 . 5. While...

FS-1010 5-30 5. Remove three screws 6 . 6. Remove one connector 7 from the laser scanner unit 8 . 7. Remove the laser scanner unit 8 . Figure 5-2-27 Removing the laser scanner unit 6 7 8

FS-1010 5-31 8. Remove the eraser lamp 9 . 9 5-2-28 Removing the eraser lamp

Chapter 6 Contents 6-1 Troubleshooting ............................................................................................................................... 6-3 6-1-1 Error messages ...............................................................................................................

6-3 FS-1010 6-1 Troubleshooting This chapter explains procedures for identifying and correcting problems. Topics covered are: 6-1-1 Error messages The printer indicates various messages using the LED indicators at its top. The indicators are lit, fast flashing, slow flashing, and off in combination ...

6-6 FS-1010 Indicator Remote Operation Panel display Description Maintenance messages The paper has run out. Add paper to thepaper cassette (1 or 2) or MP tray.The paper source is displayed in theRemote Operation Panel utility. The paper cassette is not closed securely.Close the paper cassette prope...

6-8 FS-1010 Indicator Remote Operation Panel display Description The specified file is not found. Press theGo key to resume printing. You canabandon printing by pressing the Cancelkey. Current print processing cannotcontinue.Press the Go key to resume printing.You can abandon printing by pressingthe...

6-20 FS-1010 6-1-3 Print quality problems Print quality problems range from uneven tone to completely blank output. The troubleshooting procedure for each type of problem is given below. A B C1 2 3 A B C1 2 3 A B C1 2 3 A B C1 2 3 (1) Completely blank printout See page 6-21. (2) All-black printout S...

6-28 FS-1010 (9) Dirt on the top edge or back of the paper Check toner contamination in various parts. • Dirty edges and back of the paper can be caused by toner accumulated on such parts as the paper chute, paper transportation paths, the bottom of the process unit, and the fuser unit inlet. Clean ...

6-29 FS-1010 Repetitive defects gauge Use the following measurements for checking repetitive occurrences on the printed page. See the above section for details. Figure 6-1-2 Repetitive defects gauge First occurrence of defect [63 mm] Developing roller (Process unit) [25 mm] Upper registration roller...

6-30 FS-1010 6-1-4 Correcting a paper jam If a paper jam occurs while you are printing, remove the jammed paper as described below. After you have removed the jammed paper, open and close the top cover once. (1) Jam at the face-down and face-up trays 1. Open the face-up tray and remove the jammed pa...

6-31 FS-1010 (2) Jam at the paper cassette 1. Pull out the paper cassette and remove the jammed paper. Figure 6-1-4 Jam at the paper cassette (3) Jam inside the printer 1. Open the top cover and front cover. 2. Take the process unit together with the toner container out of the printer. 3. Remove the...

Appendix A Contents Timing charts .......................................................................................................................................... A-3 1. Option paper cassette feeding, two A4 size papers .........................................................................

A-3 FS-1010 Timing charts 1. Option paper cassette feeding, two A4 size papers MO T ORN (Main motor) MHVDR (Main charger) THVDR (T ransf er charger) PFMDRN (Cassette f eed motor) RESDRN (Registr ation clutch) OUTPEN (Laser diode) BIAS (De v eloping bias) ERASPW (Er aser lamp) PLGDRN (P olygon motor)...

A-4 FS-1010 2. Option paper cassette feeding, two legal size papers MO T O RN (Main motor) MHVDR (Main charger) THVDR (T ransf er charger) PFMDRN (Cassette f eed motor) RESDRN (Registr ation clutch) OUTPEN (Laser diode) BIAS (De v eloping bias) ERASPW (Er aser lamp) PLGDRN (P olygon motor) RESIT (Re...

A-5 FS-1010 3. Option paper cassette feeding, two letter size papers MO T O RN (Main motor) MHVDR (Main charger) THVDR (T ransf er charger) PFMDRN (Cassette f eed motor) RESDRN (Registr ation clutch) OUTPEN (Laser diode) BIAS (De v eloping bias) ERASPW (Er aser lamp) PLGDRN (P olygon motor) RESIT (R...

A-7 FS-1010 5. MP tray feeding, two legal size papers MO T O RN (Main motor) MHVDR (Main charger) THVDR (T ransf er charger) MPFSOL (MP f eed clutch) RESDRN (Registr ation clutch) OUTPEN (Laser diode) BIAS (De v eloping bias) ERASPW (Er aser lamp) PLGDRN (P olygon motor) RESIT (Registr ation sensor)...

A-8 FS-1010 6. MP tray feeding, two letter size papers MO T ORN (Main motor) MHVDR (Main charger) THVDR (T ransf e r charger) MPFSOL (MP f eed clutch) RESDRN (Registr ation clutch) OUTPEN (Laser diode) BIAS (De v eloping bias) ERASPW (Er aser lamp) PLGDRN (P olygon motor) RESIT (Registr ation sensor...

A-9 FS-1010 DGND _S/H _VIDEO _LDEN DGND +5V -IL DGND _HSYNC FPRSTN GND FPCLK FPDIR FPDA T +3.3 V YC301 High voltage board YC-T YC-M CN1 CN2 CN2 F1 : 250 V /8 A (E) 250 V /15 A (U) F2 : 250 V /1.6 A (E) 250 V /2.5 A (U) Power supply board Power switch Interlock switch CN4 CN1 CN5 N L THERM +5V AC S02...

Appendix B Contents Status page ............................................................................................................................................. B-3 Printing the service status page ............................................................................................

B-3 FS-1010 Status page The printer can print different types of the status page—the user (normal) status page and the service status page. This section exclusively describes information obtainable with the service status page. For information on the user (normal) status page, refer to the printer’s...

B-4 FS-1010 Service information on the status page An example of the service status page is shown below. (Note the details born by the status page my differ from a firmware version to another.) Most of the service information are located under Service information . Most of these service information ...

Appendix C Contents Parallel interface .................................................................................................................................... C-3 Selecting the parallel interface mode .........................................................................................

C-3 FS-1010 Parallel interface The printer uses a bidirectional parallel interface for high-speed data transmission for the host computer. This interface includes the buffers which are compatible with the IEEE 1284 standards. The parallel interface provides support for the ECP and nibble modes in th...

C-4 FS-1010 Parallel interface pin assignment The pins of the parallel interface connector carry the signals listed below. The function for each signal is detailed on the following page. No. Terminal Signal No. Terminal Signal 1 nStrobe (STBIN1/2*) 19 Ground GND 2 Data1 (PAD0) 20 Ground GND 3 Data2 ...

C-5 FS-1010 Signal Meaning A negative-going Strobe* pulse causes the printer to read and latch the data on the Data 0 [1] to Data 7 [8] signal lines. These eight signals form the data byte sent from the host computer to the printer. Data 7 [8] is the most significant bit and Data 0 [1] is the least ...

C-6 FS-1010 USB interface This printer supports the USB (Universal Serial Bus) Revision 1.1 standards. USB interface specifications and interface signals are as follows: Item Specifications Basic specification Complies with the USB Revision 1.1 standards. Connectors Printer: B-type receptacle (femal...

C-7 FS-1010 Serial interface (Optional) The printer is equipped with an optional slot for adding a serial port. To add a serial port, the serial interface board is equipped. The device responsible for controlling the serial interface is integrated in the gate array in the controller system. The seri...

C-9 FS-1010 Serial interface signals The following table provides details for the signals used on the serial interface board. Signal Meaning FG (Pin 1) This pin is connected directly to the printer frame. TxD (Pin 2) RS-232C only: This output carries asynchronous data sent by the printer to the comp...

C-10 FS-1010 RXD TXD DTR GND DSR RTS CTS TXD RXD RTS CTS DSR SG DTR 2345678 234567) Computer serial port (DB-9) Printer serial port (DB-25) GND TXD RXD RTS CTS DSR GND DTR FG TXD RXD RTS CTS DSR SG DTR 1234567) 1234567) Computer serial port (DB-25) Printer serial port (DB-25) Connector configuration...

C-11 FS-1010 RS-422A Frame ground Signal ground Rx terminal Tx terminal FG RD − SG SD − SD + RD + 13790* Computer serial interface Printer serial port (DB-25) On the computer serial port, investigate pin assignments depends on the computer manufacture’s instruction. Since the RS-422A configuration d...

©2001 KYOCERA MITA CORPORATION is a trademark of Kyocera Corporation is a registered trademark of KYOCERA MITA CORPORATION KYOCERA MITA AMERICA, INC. Headquarters:225 Sand Road, P.O. Box 40008Fairfield, New Jersey 07004-0008TEL : (973) 808-8444FAX : (973) 882-6000 New York Show Room:149 West 51st st...