KOBE CH7642SQB - Manuals

3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Duct Cover Box (Sold Separately) {A} KOBE Range Hood {B} Warranty Registration Card {C} Instruction Manual {D} Baffle Filter -- 2 (30”, 36”, 42”) -- 3 (48”) {E} Stainless Steel Spacer -- 0 (30”) -- 1 (36”) -- 3 (4...

4 INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1 or TABLE 2. (All calculation in inches.) - FOR UNDER THE CABINET - TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: ...

6 UNDER THE CABINET INSTALLATION P r e p a r a t i o n b e f o r e I n s t a l l a t i o n NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. • A straight, short vent run will a...

7 4. Draw electrical wires through cabinet access opening. 5. From inside of the hood, place screw (not provided) into the exact center of each knockout hole and secure to cabinet bottom. Once all mounting screws are in place, finish tightening screws until secure. CAUTION : MAKE SURE THE HOOD IS SE...

8 A c c e s s o r i e s 9. Drop oil tunnel into recess support near rear of hood. Refer to Figure 6. 10. Install baffle filters and stainless spacer(s). Refer to Measurements and Diagrams on page 22 for baffle filter and stainless spacer placement. Angle baffle filter toward back of hood . Push baff...

9 STAND ALONE INSTALLATION *** This installation only applies if installing with the CH1120DC duct cover. P r e p a r a t i o n b e f o r e I n s t a l l a t i o n NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the ho...

12 F i n a l A s s e m b l y 14. Turn power ON in control panel. Check all light and fan operation. 15. Make sure to leave this manual for the homeowner. Figure 19

13 OPERATION INSTRUCTIONS This KOBE hood is equipped with six electronic controls, two powerful centrifugal squirrel cages with stainless steel oil tunnel, stainless steel baffle filters and spacer(s), and bright 12-volt 20-watt halogen lights (2 for 30” & 36” and 3 for 42” & 48”). The six e...

15 MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly. To Clean Hood Surface CAUTION : NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular c...

16 To Replace Light Bulb CAUTION : HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. 1. Make sure all controls are off, and range hood is unplugged. 2. Place a flat-head screwdriver between light cover and housing to remove cover . 3. Gently pull defective bulb straight out and discard. Light ...

17 SPECIFICATIONS MODEL / SIZE CH7630SQB / 30” CH7636SQB / 36" CH7642SQB / 42” CH7648SQB / 48” COLOR #304 Commercial Grade Stainless Steel CONSUMPTION / AMPERE CH7630SQB – 300W / 3A CH7636SQB – 300W / 3A CH7642SQB – 300W / 3A CH7648SQB – 300W / 3A VOLTAGE 120V 60Hz NUMBER OF MOTORS 2 DESIGN Seam...

18 MEASUREMENTS & DIAGRAMS All ( ) are in millimeter. All inch measurements are converted from millimeters. Inch measurements are estimated. - FOR UNDER THE CABINET - MODEL NO: CH7630SQB CH7636SQB CH7642SQB CH7648SQB

20 Rear Knockout Holes 24" (60 8) fo r 42 " 30" (76 0) fo r 48 " 18" (45 6) fo r 36 " 3" (7 5) 3" (7 5) 3" (7 5) 3" (7 5) 12" (30 4) fo r 30 " 2 " (5 1 ) 4" ( 102 )

21 Hood-Mounting Bracket DUCT COVER-MOUNTING BRACKET Inner Duct Cover-Mounting Bracket Outer Duct Cover-Mounting Bracket 11 -3 /4" (2 98 ) 1 -3 /1 6 " (3 0 ) 1-1 /4" ( 32.5 ) 8- 5/8 " ( 21 9) 8-5 /8" (2 20 ) 11 -3 /4" (2 98 ) 7 /8 " (2 2 ) 1 /8 " (4 .5 ) 3-1 /8" (...

22 BAFFLE FILTER & STAINLESS STEEL SPACERS 30 ″ H00D 42 ″ H00D 36 ″ H00D 48 ″ H00D

23 PARTS LIST MODEL NO.: CH7630SQB CH7636SQB CH7642SQB CH7648SQB Body Components NO. DESCRIPTION MODEL/SIZE PART NO. 1 Screws (3/16” x 3/8”) CH176-1 2 Hood Casing CH176-2 3 Hood-Mounting Bracket CH176-3 4 Screws (3/16” x 3/8”) CH176-1 5 Stainless Steel Oil Tunnel CH176-4 6 Blower Assembly CH176-5 7 ...

27 CIRCUIT DIAGRAM MODEL NO.: CH7630SQB CH7636SQB MOTOR MOTOR CAPACITOR 10uF/450V CAPACITOR 10uF/450V TRANSFORMER PROCESSOR BOARD CONTROL BOARD HALOGEN LIGHT RED BLACK WH IT E Y E L L O W G R E E N B R O WN B R O WN R E D R E D G R E E N G R E E N WH IT E WH IT E R E D B L A C K B L A C K B L A C K ...

29 DISCLAIMER 1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM. Upon acceptance of items, owner assumes responsibility for its safe arri...

30 WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods, Inc. warrants all products manufactured or supplied by it to be free from defects in workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement...

32 PRODUCT REGISTRATION Register Your Product! Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE ...

KOBE Range Hoods 10505 Valley Blvd Suite # 302 El Monte, CA 91731 USA http://www.KOBERangeHoods.com This KOBE hood is manufactured for use in the USA and CANADA only. W e do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that c...