Intel SC450NX - Manuals - manualsarea.com

Page 5 - Safety Guidelines; Before you remove a server cover, observe these safety guidelines:; Server Precautions; WARNINGS; front panel of the server

v Safety Guidelines Before you remove a server cover, observe these safety guidelines: • Only technically qualified personnel should integrate the server. • Turn off all peripheral devices connected to the server. • Turn off the server using the push-button on/off power switch on the front panel of ...

Page 6 - CAUTIONS; ESD; ESD can; Boards and modules can be extremely; Operating the server with the covers

vi CAUTIONS E LECTROSTATIC DISCHARGE (ESD) AND ESD PROTECTION : ESD can damage disk drives, add-in boards, and other components. This server canwithstand normal levels of environmental ESD while hot-swapping SCSI harddisk drives. However, we recommend doing all procedures in this manualonly at an ES...

Page 7 - Equipment Rack Precautions; : The operating temperature of the server, when installed in an

vii Equipment Rack Precautions WARNINGS A NCHOR THE EQUIPMENT RACK : The equipment rack must be anchored to an unmovable support to prevent it from falling over when one or moreservers are extended in front of it on slide assemblies. The anchors mustbe able to withstand a force of up to 113 kg (250 ...

Page 9 - Contents

ix Contents Safety Guidelines Server Precautions ............................................................................................................... vEquipment Rack Precautions ..............................................................................................vii Introduction ...

Page 11 - Introduction; This guide explains three processes:

11 Introduction The SC450NX MP server is designed to either stand upright (pedestal mode) or be mounted in a rack(rack mode). Figures 1 and 2 on page 12 show examples of these configurations. Before operation,you must purchase an adapter kit to configure the server for one of the two modes. If you h...

Page 12 - Tools You Need; Pencil

12 Table 1. SC450NX MP Server Physical Specifications Specification Pedestal Mode Rack Mode Height 48.26 cm (19 inches) 7u Width 31.12cm (12.25 inches) 19 inch rack Depth 63.5cm (25 inches) 25 inches Weight 38.25 kg (85 lbs) minimum configuration45 kg (100 lbs) maximum configuration 38.25 kg (85 lbs...

Page 13 - Configuring for Rack Mount; Before starting, please read “Safety Guidelines” on page v.; Prepare the Slide Assemblies; Remove the slide assemblies from the kit.

13 Configuring for Rack Mount Before starting, please read “Safety Guidelines” on page v. Prepare the Slide Assemblies See Figure 3. 1. Remove the slide assemblies from the kit. 2. Orient a slide assembly so that the smallest outer bar is facing down. 3. Fully extend the telescoping slide assembly u...

Page 14 - Prepare the Server; Attaching the Bezel Frame and Door; WARNING; : To avoid personal injury when unpacking the server, use; Use four screws from the kit to attach the handles to the chassis.

14 Prepare the Server Before you can install the server in the 19-inch equipment rack, you must install a bezel, handles, andthe small bars of the slide assemblies onto the sides of the server. Attaching the Bezel Frame and Door To be installed in a rack, the server needs a bezel frame with rectangu...

Page 15 - Attach the Small Bar of the Slide Assembly to the Server; Remove four screws from the kit.

15 Attach the Small Bar of the Slide Assembly to the Server See Figure 4. 1. Remove four screws from the kit. 2. While facing the side of the server, orient the small bar so that the flat side faces the top and theright-angle end faces the front of the server. 3. Align the first hole in the right-an...

Page 16 - Prepare the Equipment Rack; NOTE

16 Prepare the Equipment Rack Before you can install the server in the 19-inch equipment rack, you must attach the center bar andlarge outer bar assemblies to the vertical rails of the rack. Attach the Right-angle Extension Brackets to the EquipmentRack / NOTE Mounting holes in the vertical rails of...

Page 18 - Install the Server in the Rack; : The equipment rack must be anchored; : To avoid personal injury when unpacking the server, use; Connect all external cables and the power cord(s) to the server.

18 Install the Server in the Rack WARNINGS A NCHOR THE EQUIPMENT RACK : The equipment rack must be anchored to an unmovable support to prevent it from falling over when one or moreservers are extended in front of it on slide assemblies. The anchors mustbe able to withstand a force of up to 113 kg (2...

Page 21 - Configuring for Pedestal Mount; Install Chassis Feet; Remove two system feet and two screws from the kit.; Install the Top and Side Covers; Observe the safety guidelines on page v.

21 Configuring for Pedestal Mount Install Chassis Feet See Figure 8. 1. Remove two system feet and two screws from the kit. 2. Each system foot has one screw hole and, on the opposite end, two slots that fit two tabsextending from the chassis wall. Orient the chassis foot to align these features wit...

Page 22 - Install Bezel Frame and Door

22 Install Bezel Frame and Door 1. Attach the bezel frame by inserting the tabs at the corner of the frame into their correspondingrectangular slots on the chassis. 2. Attach the bezel door: with the door all the way open (left, as it stands upright in a pedestalmount), align the tabs on the door wi...

Page 23 - Changing from Pedestal to Rack; Remove and save the single screw from the back of the TOP cover.

23 Changing from Pedestal to Rack To change your server from pedestal mode to rack mode, you must complete two basic steps:removing the components of the pedestal mount, then configuring the server for a rack mount.Because configuring for a rack mount was described in an earlier section (page 13), t...

Page 24 - Exchange the Bezel Frame; Reattach the bezel door to its hinges on the chassis.

24 Exchange the Bezel Frame To be installed in a rack, the server needs a new bezel frame with rectangular cutouts where thechassis handles fit. You need to remove the old bezel frame and install the new one from the rack kit. 1. Remove the bezel door: with the door open all the way (to the left), l...