INSTEON 2633-442 (UK) - Manuals

Page 2 - TABLE OF CONTENTS

Page 2 of 14 Rev: 1/21/2014 7:47 AM TABLE OF CONTENTS About On/Off Module .................................................................................................................................. 2 Features and Benefits ..........................................................................

Page 3 - Features and Benefits; controller; Installation; CAUTIONS AND WARNINGS; In the Box; None

Page 3 of 14 Rev: 1/21/2014 7:47 AM Features and Benefits - Integrated on/off relay - Compatible with all INSTEON (and X10) controllers; can also act as an INSTEON (and X10) controller - Super-easy setup with multi-color LED and beeper - Dual-band communicates simultaneously over both RF and powerli...

Page 4 - Using On/Off Module Paddle; On; Brighten; Green; Off; Red; Adjust Local Settings; ) Press and hold On/Off Module set button until it beeps a third time; Error Blink

Page 4 of 14 Rev: 1/21/2014 7:47 AM Using On/Off Module Paddle On/Off Module’s paddle will control the load and any additional linked responders with tap, double-tap and press and hold actions to initiate different behaviors. On/Off Module Paddle Tap Press and hold Double-tap LED Top On Brighten unt...

Page 5 - Beep on Button Press; INSTEON Setup; INSTEON Controllers, Responders and Links; Configure INSTEON Settings; Controller will double-beep and its LED will stop blinking

Page 5 of 14 Rev: 1/21/2014 7:47 AM Beep on Button Press Default = disabled This setting is only adjustable via software or a central controller. On/Off Module will beep every time its paddle is tapped. INSTEON Setup Some products have subtle differences in their setup procedures. Please refer to th...

Page 6 - Make On/Off Module a Controller; Make On/Off Module a Responder; Groups

Page 6 of 14 Rev: 1/21/2014 7:47 AM Make On/Off Module a Controller 1) Press and hold On/Off Module set button until it beeps On/Off Module LED will start blinking green You will have four minutes to complete the next steps before linking mode times out 2) Adjust responder to desired state 3) Press ...

Page 7 - Make On/Off Module a Controller of Multiple Responders

Page 7 of 14 Rev: 1/21/2014 7:47 AM 3) Adjust On/Off Module to desired level (on or off) 4) Press and hold On/Off Module set button until it double-beeps 5) For each additional scene member: a) Adjust member to desired scene brightness b) Press and hold set button until it double-beeps 6) Tap contro...

Page 8 - Remove On/Off Module as a Controller of Multiple Responders

Page 8 of 14 Rev: 1/21/2014 7:47 AM Remove On/Off Module as a Controller of Multiple Responders 1) Press and hold On/Off Module set button until it beeps LED will start blinking green 2) Press and hold On/Off Module set button until it beeps a second time LED will start blinking red 3) Tap On/Off Mo...

Page 9 - Specifications

Page 9 of 14 Rev: 1/21/2014 7:47 AM Example: A1-OFF-A1-OFF-A1-OFF or A1-A1-A1-AOFF On/Off Module will double-beep and LED will stop blinking 4) Test by sending X10 on and off commands On/Off Module will not respond Specifications General Product name On/Off Module Brand/manufacturer INSTEON Manufact...

Page 11 - All product specifications are subject to change.; Troubleshooting; Problem

Page 11 of 14 Rev: 1/21/2014 7:47 AM Electrical Voltage 100VAC to 240VAC (+/- 10%) Frequency 50/60Hz auto detected at power-up Maximum load 16A – 240VAC (EUR) 10A – 240VAC (AUS/NZ) 3600W/240VAC Resistive 700W/240VAC Inductive/Capacitive 2000W/240VAC Bulbs/Low Voltage Halogen Minimum load N/A Load ty...

Page 12 - Factory Reset; Phase Bridge Detect Beacon/RF Range Test

Page 12 of 14 Rev: 1/21/2014 7:47 AM Other electrical devices, such as computers, televisions or power strips, may be absorbing the INSTEON signal On/Off Module is taking a long time to respond to a controller The controller may be sending commands to a responder that is no longer in use. Commands f...

Page 13 - Certification and Warranty

Page 13 of 14 Rev: 1/21/2014 7:47 AM INSTEON products or buildings with both 2- and 3- phase circuits. The phase bridge detect beacon can also be used as an RF range test to see if your devices are within communication range. You will need at least one other INSTEON dual-band device installed. 1) Pr...