INSTEON 2485S (On/Off Switch) - Manuals

INSTEON 2485S (On/Off Switch) – Manual in PDF format online.

Manuals:

Manual

Manual INSTEON 2485S (On/Off Switch)

Summary

Page 2 - KeypadLinc Schedule Timer Owner’s Manual; TABLE OF CONTENTS

KeypadLinc Schedule Timer Owner’s Manual TABLE OF CONTENTS ABOUT KEYPADLINC SCHEDULE TIMER ................................................................................................................. 3 Key KeypadLinc Schedule Timer Features .........................................................

Page 3 - ABOUT KEYPADLINC SCHEDULE TIMER; Key KeypadLinc Schedule Timer Features; Feature

KeypadLinc Schedule Timer Owner’s Manual Page 3 of 26 ABOUT KEYPADLINC SCHEDULE TIMER KeypadLinc Schedule Timer presents you with an elegant and stylish way to control a wired-in light and add timer capabilities to your existing INSTEON devices. Use the buttons on KeypadLinc to create and control cu...

Page 4 - How Does INSTEON Work?; INSTALLATION; Tools You Will Need; CAUTION

KeypadLinc Schedule Timer Owner’s Manual Page 4 of 26 What is Included with KeypadLinc Schedule Timer • 1x - KeypadLinc Schedule Timer – INSTEON Keypad Schedule Timer with Dimmer or On/Off Switch • 2x - Mounting screws • 4x - Wire nuts • 1x - Quick-Start Guide WHAT IS INSTEON? Since its inception in...

Page 5 - Additional KeypadLinc Dimmer precautions; Identifying the Electrical Wires in your Home; into

KeypadLinc Schedule Timer Owner’s Manual Page 5 of 26 • Be sure that you have turned off the circuit breaker or removed the fuse for the circuit you are installing KeypadLinc in. Installing KeypadLinc with the power on will expose you to dangerous voltages. • Connect only copper or copper-clad wire ...

Page 6 - from the junction box.; Wiring Diagram; Installing KeypadLinc Schedule Timer in a Multi-Way Circuit

KeypadLinc Schedule Timer Owner’s Manual Page 6 of 26 Installing KeypadLinc Schedule Timer 1) At the circuit breaker or fuse panel, disconnect the power for all of the circuits in the switch junction box. Verify that the power is off by trying to turn on the lights controlled by the switches. 2) Rem...

Page 7 - Understanding Multi-Way Circuits

KeypadLinc Schedule Timer Owner’s Manual Page 7 of 26 Installing KeypadLinc Schedule Timer in a Multi-Way Circuit Understanding Multi-Way Circuits If more than one switch controls a single set of lights (called a load), the switches are part of a multi-way circuit. A 3-way circuit uses two switches ...

Page 8 - Using KeypadLinc Schedule Timer in Virtual Multi-Way Circuits; Once KeypadLincs have been installed, you can create a; KeypadLinc

KeypadLinc Schedule Timer Owner’s Manual Page 8 of 26 Using KeypadLinc Schedule Timer in Virtual Multi-Way Circuits Once KeypadLincs have been installed, you can create a virtual multi-way circuit to control a single load. Rather than connect each switch directly to the load, virtual multi-ways use ...

Page 9 - Step-by-Step Instructions for Installing Multi-Way KeypadLincs; Connect the; Secondary’s LINE wire.; Cap the red LOAD wire from the KeypadLinc Secondary.; Put a wire; Secondary’s NEUTRAL wire.

KeypadLinc Schedule Timer Owner’s Manual Page 9 of 26 Step-by-Step Instructions for Installing Multi-Way KeypadLincs When replacing a 3-way mechanical switch, each switch will have three wires connected to it from the wall box. Four-way or greater circuits will have four wires connected to the switc...

Page 10 - Special Treatment for 4- or More-Way Circuits; Cross-Linking INSTEON Devices

KeypadLinc Schedule Timer Owner’s Manual Page 10 of 26 6) Connect the KeypadLinc Secondary’s GROUND Wire. Connect the bare copper GROUND wire to the other GROUND wire in the junction box. 7) Install additional KeypadLinc Secondaries. If you have a 4-way or greater switching circuit, see Special Trea...

Page 11 - Step-by Step Instructions for Installing Multi-Way KeypadLincs.

KeypadLinc Schedule Timer Owner’s Manual Page 11 of 26 Special Treatment for 4- or More-Way Circuits If your lighting circuit includes more than two switches controlling a single set of lights, those extra switches will have four wires connected to them. Two of the wires are TRAVELERS from the prece...

Page 12 - USING KEYPADLINC SCHEDULE TIMER; Using the Buttons to Control Scenes

KeypadLinc Schedule Timer Owner’s Manual Page 12 of 26 USING KEYPADLINC SCHEDULE TIMER Using the Buttons to Control Scenes On/Off Buttons The load (device wired-in to KeypadLinc) can be controlled by using the dedicated On/Off buttons. If you wish to include the load in a scene, you must use the ded...

Page 13 - Entering Time in KeypadLinc Schedule Timer.; Programming a Timer in KeypadLinc Schedule Timer; Entering Time in KeypadLinc

KeypadLinc Schedule Timer Owner’s Manual Page 13 of 26 Setting the Clock in KeypadLinc Schedule Timer 1) Set KeypadLinc to Programming Mode by pressing & holding the Set button for 3 seconds The LED will cycle between the On, A, and B buttons 2) Tap the A button to enter Clock Setup Mode KeypadL...

Page 14 - Ramp Rate; Setting the On-Level on KeypadLinc Dimmer; KeypadLinc will beep; BE CAREFUL

KeypadLinc Schedule Timer Owner’s Manual Page 14 of 26 NOTE: If any LEDs are flashing, you held the Set button down too long. Holding down the Set button for 3 seconds places KeypadLinc into Programming Mode. Programming Mode will time out after 4 minutes of inactivity. To manually exit Programming ...

Page 15 - Approximate

KeypadLinc Schedule Timer Owner’s Manual Page 15 of 26 NOTE: If the load flashes twice, you didn’t double-press the Set button fast enough and the KeypadLinc On-Level was actually set up twice. Reset the correct On-Level and try setting the Ramp Rate again from step 1. Setting the Ramp Rate on Keypa...

Page 16 - Linking KeypadLinc Schedule Timer to an INSTEON Responder; Unlinking an INSTEON Responder from KeypadLinc Schedule Timer; The button’s LED will begin blinking

KeypadLinc Schedule Timer Owner’s Manual Page 16 of 26 BE CAREFUL - Any accidental button presses will exit Linking Mode early. CONTROLLING INSTEON RESPONDERS FROM KEYPADLINC SCHEDULE TIMER Linking KeypadLinc Schedule Timer to an INSTEON Responder To use KeypadLinc as an INSTEON Controller, follow t...

Page 17 - Unlinking KeypadLinc Schedule Timer from an INSTEON Controller; The following will work for the most common INSTEON devices:; twice; twice; The button’s LED will flash once and then turn on solid; CREATING INSTEON SCENES

KeypadLinc Schedule Timer Owner’s Manual Page 17 of 26 CONTROLLING KEYPADLINC SCHEDULE TIMER FROM AN INSTEON CONTROLER Linking an INSTEON Controller to KeypadLinc Schedule Timer To use KeypadLinc as an INSTEON Responder, follow these steps to Link KeypadLinc and a Controller together. Refer to the C...

Page 18 - ADVANCED FEATURES

KeypadLinc Schedule Timer Owner’s Manual Page 18 of 26 ADVANCED FEATURES Multi-Linking and Multi-Unlinking Multi-Linking Multi-Linking Mode allows you to Link multiple Responders to a single Controller and quickly create an INSTEON scene. Once the Controller is in Multi-Linking Mode, you can Link an...

Page 19 - Cross-Linking Two INSTEON Devices

KeypadLinc Schedule Timer Owner’s Manual Page 19 of 26 Cross-Linking INSTEON Devices Cross-Linking Two INSTEON Devices Cross-Linking devices allow you to track the on/off status of the load on all Linked INSTEON Responders. For this example we will use a primary device controlling the load and one s...

Page 20 - The LED will cycle between the On, A, and B buttons; Disabling a Scene’s On/Off Timers; Resetting KeypadLinc; Restoring Power to KeypadLinc Schedule Timer; Setting the Clock in KeypadLinc Schedule

KeypadLinc Schedule Timer Owner’s Manual Page 20 of 26 Viewing/Editing a Scene’s On/Off Timers 1) Set KeypadLinc to Programming Mode by pressing & holding the Set button for 3 seconds The LED will cycle between the On, A, and B buttons 2) Tap the B button to enter Timer Setup Mode KeypadLinc wil...

Page 21 - Unlinking KeypadLinc Schedule Timer from an INSTEON Controller.; X10 PROGRAMMING OPTIONS; Setting the X10 Address; three times; For example, to assign the address A1, you would send “A1 ON A1 ON A1 ON.”; Removing the X10 Address; three; For example, to remove the address A1, you would send “A1 ON A1 ON A1 ON”.

KeypadLinc Schedule Timer Owner’s Manual Page 21 of 26 Resetting KeypadLinc Schedule Timer to its Factory Default Settings The factory reset procedure can be used to clear the KeypadLinc memory of all INSTEON Links, timers, programmed On-Levels and Ramp Rates, X10 addresses, etc. 1) If you are using...

Page 22 - ABOUT INSTEON; Using Dual-Band INSTEON Devices to Upgrade Your Network; Why do I need to bridge these phases?; Further Enhancing Reliability; ADDITIONAL RESOURCES

KeypadLinc Schedule Timer Owner’s Manual Page 22 of 26 ABOUT INSTEON Using Dual-Band INSTEON Devices to Upgrade Your Network What are phases? The majority of single-family homes in North America have two phases (or “legs”) of 110 Volts coming into their electricity panels. From the panel, they are d...

Page 23 - TROUBLESHOOTING; Problem

KeypadLinc Schedule Timer Owner’s Manual Page 23 of 26 TROUBLESHOOTING Problem Possible Cause Solution The LEDs on KeypadLinc are not turning on and won’t control the load. KeypadLinc may not be getting power. Make sure the circuit breaker is turned on. Make sure the air gap (Set button) is not pull...

Page 25 - SPECIFICATIONS, CERTIFICATION, AND WARRANTY; Specifications

KeypadLinc Schedule Timer Owner’s Manual Page 25 of 26 Problem Possible Cause Solution KeypadLinc trips the Arc Fault Circuit Interrupter (AFCI). The AFCI might be too sensitive. Replace the AFCI with a less sensitive brand or model from a hardware store with a customer-friendly return policy. Testi...

Page 26 - Limitations

KeypadLinc Schedule Timer Owner’s Manual Page 26 of 26 Limited Warranty Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will perform in substantial con...