INSTEON 2442-422 (EU) - Manuals

Page 4 - About Micro Dimmer; Features and Benefits; In the Box; Before Installation

Page 4 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM About Micro Dimmer Features and Benefits - Integrated dimmer featuring 32 dim levels and 32 ramp rates - Wires in behind existing wall switch or in fixture box (requires neutral wire) - Compatible with latching, single momentary and du...

Page 5 - Identify Switch Type

Page 5 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM specifications. If this device supports dimming, please note that dimming an inductive load, such as a fan or transformer, could cause damage to the dimmer, the load bearing device, or both. If the manufacturer of the load device does ...

Page 6 - Installation

Page 6 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Installation 1) Write down the INSTEON ID found on the back of the unit (XX.XX.XX) 2) Turn off breaker/fuse and verify that the power is off 3) Disconnect wires from existing switch, fixture or outlet and prep all wires to be connected...

Page 7 - Switch Operation Mode; Change to Single Momentary Mode

Page 7 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM LED will start blinking green b) Press and hold set button until it beeps a second time LED will start blinking red c) Press and hold set button until it beeps a third time LED will start blinking green d) Perform the step that applies...

Page 9 - Local Control Operation; Single Momentary Switch

Page 9 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Local Control Operation Micro module’s switch operation mode affects how it responds to commands from the switch. This is why it’s important to program Micro module for the specific type of switch you are using. Micro module’s on/off b...

Page 10 - Adjust Local Settings; Local Ramp Rate

Page 10 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Adjust Local Settings Local On-Level The local on-level is the brightness at which the connected load will come on when turned on at the switch wired into Micro module. The default on-level is 100% brightness, but it can be set to any...

Page 11 - Ramp Rate Presets; Resume Dim

Page 11 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Ramp Rate Presets “Instant” 0.5 seconds (factory default) 2 seconds 5 seconds 9) Test by turning off and then back on via the local switch Light will ramp off and back on at the new local ramp rate Resume Dim When resume dim is enable...

Page 12 - INSTEON Setup; INSTEON Controllers, Responders and Links; controller

Page 12 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Error Blink Default = enabled This setting is only adjustable via software or a central controller. Micro module LED will blink red once for a few seconds if one or more responders do not acknowledge a message and will blink green onc...

Page 16 - Factory Reset; Add X10 Address

Page 16 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Micro module will beep and LED will stop blinking 6) Test by tapping the switch wired into Micro module on and off None of the former responders will respond Factory Reset All settings and scenes will be erased and return to factory d...

Page 17 - Specifications

Page 17 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Specifications General Product name Micro Dimmer Brand/manufacturer INSTEON Manufacturer product number US 2442-222 EU 2442-422 AUS/NZ 2442-522 UPC US 813922012705 EU 813922012712 AUS/NZ 813922012729 Warranty 2 years, limited INSTEON ...

Page 20 - Troubleshooting; Problem

Page 20 of 24 2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM Troubleshooting Problem Possible Cause Solution The LEDs on Micro module are not turning on at all Micro module is not getting power Make sure the circuit breaker is turned on Check junction box wires to ensure all connections are tig...

Page 23 - Certification and Warranty

Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized c...