Honeywell VTXVTXM - Manuals

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-12 F.5.2 Profibus Module Configuration The Profibus interface is shipped from the factory with the address set to 3, the speed set to 19200 baud, and the memory length set to 122 words. The memory length to can be reduced to 41 words...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-13 F.6 DeviceNet Interface (P/N 1295-0329) The DeviceNet network is a low-level network that provides connections between simple industrial devices and higher-level devices (such as PLC controllers and computers). DeviceNet network u...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-14 F.7 ControlNet Interface ControlNet a real-time, control-layer networ k providing for high-speed transpor t of both time-critical I/O data and messaging data, including upload/download of programming and configuration data and pee...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-15 F.8 DF1 Interface (P/N1295-0343) This module emulates the DF1 slave functionality of an Allen-Bradley SLC 5/03 DF1 port. It responds to queries for data from the N14 integer file by sending alarm, fault, and concentration data. Th...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-16 F.9 Modbus Plus Interface (P/N1295-0330) For more information on Modbus Plus, see http://eclipse.modicon.com . Technical information on the ProSoft Technology MVI46-MBP interface which is used in the Vertex can be found at http://...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-17 F.10 LonWorks Interface (P/N 1295-0329) The LonWor ks protocol per mits peer-to-peer c o m m u n i c a t i o n w i t h o u t r e l y i n g o n a c e n t r a l controller. Routers permit expansion of networks to include thousands o...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-18 F.11 Modbus/TCP (P/N1295-0520) M o d b u s / T C P p r o v i d e s t h e h i g h l y r e l i a b l e communications like the other fieldbusses over fast, economical Ethernet media. This interface uses ProSoft-Technology MVI46-MNET...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-19 Figure F-6 -- HyperTerminal Setup for Diagnostic Port Figure F-7 -- WATTCP.CFG File This procedure is used to set the IP Address Procedure 1 1. Determine the desired IP address, subnet mask, and default gateway. Usually a network ...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-21 WARNING It is essential that Ethernet/CIP clients which communicate with the Vertex monitor the “Heart - beat” byte in word 40. This is because the MVI46-DFNT will continue to communicate if the Vertex PLC ceases to run. External ...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-23 F.13 RSView32 Active Display Set-Up Instructions Three terms have special meanings in this section: Rack – The DAQ PC inside the Vertex rack. Remote Station – A computer external to the Vertex rack. The desktop computer will be us...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-24 Ensure that all functionality is enabled by selecting Hardware, Optional from the Customized Windows Update as shown in Figure F-10. Figure F-10 Add Rockwell Software to Rack The RSView active display server is not installed on th...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-25 Active Display software is distributed via a CD labeled RSView32 and Active Display TM . For users on the Honeywell network, this software is available in the Rockwell Software folder at \\158.100.40.11\vtxinstl\ . The splash scre...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-26 When the setup program starts, click Client Install, highlighted in green in Figure F-13. Figure F-13 When the Rockwell software is properly installed on the remote client, the Windows control panel program list will include the f...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-27 Add Rockwell License Files to the Rack (Master Disc Activation Method) Moving license files requires that all Rockwell applications be shut down, including RSLinx. To stop RSLinx, right-click the RSLinx icon (highlighted in green ...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-28 Add Rockwell License Files to the Rack (Factory Talk activation method) The Rockwell Factory Talk activation method consists of a host ID device that contains the license file locked to that particular host device’s MAC address an...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-29 rack computer (the description will be similar to “Realtek RTL8150 USB 10/100 Fast Ethernet Adapter #x”. Click Next. i. Verify the information on the confirm screen and click Next. j. On the following screen, note the file name an...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-30 If the Vertex Rack does not currently use Factory Talk Activation: The Factory Talk Activation Tool software must be installed on the Vertex rack and configured. A host device must also be purchased to host the license. The Factor...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-31 When OK is clicked, a Microsoft Component Services Management Console window, shown in Figure F-19, will appear. If a DCOM Configuration Warning! message appears (similar to the one in Figure F-18), close it by clicking Yes. Figur...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-32 Figure F-22 Typical objects that might be added:• Administrators • ANONYMOUS LOGON • Everyone • Guests • INTERACTIVE • NETWORK • SYSTEM • Users Other Settings on Rack None. Other Settings on Desktop Windows’ firewall is incompatib...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-33 Add a new account as shown in Figure F-24 and add Honeywell Analytics to the Administrators group. Figure F-24 Create HMI account (optional) It is often useful to create multiple HMI accounts. This facilitates using the HMI securi...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook F-34 Figure F-27 Click the Save user name and password (shown in Figure F-27) checkbox and then click OK. Figure F-28 Figure F-29 Debugging 1. Occasionally, a failed operation is manifestedby the desktop Active Display screen being all...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook G-1 G Line Integrity Test Option

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook G-2 H o n ey we l l A n a l y t i c s n ow o f fe r s t h e o p t i o n a l capability to check for leaks in Vertex sample lines. Analyzers equipped with option 1295-0510 detect a pneumatic signal from valves installed at the end of th...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook G-3 Figure G-1 -- Simplified Pneumatic Schematic In practice, the sample pressure measurements are made as a differential measurement with the pump on and then off. This eliminates the effect of any transducer offset. However, since an...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook G-4 The LIT measurement requires that the total pressure variance of the sampled point, the Vertex rack and the exhaust outlet must be less than 0.3 in. Hg. for correct operation (see Figure G-1). Software Overview Automatic LI tests c...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook G-5 checkmark will be set. LIT Access from RSView RSView has two buttons. 1. Two buttons in the Authorized Service screen as shown in Figure G-5. When the associated analyzer is in Monitor mode this will appear as shown in Figure G-6. ...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook G-6 Pressing the “Record Known Good LITC” button will cause a characterization to be performed on all analyzers in the rack. Similarly, pressing the “Line Integrity Test” button will cause a line integrity test to be performed immediat...

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook H-1 H Warranty Statement

V ertex TM 72-Point Continuous Monitor Vertex Technical Handbook H-2 All products are designed and manufactured to the latest internationally recognized standards by Honeywell Analytics under a Quality Management System that is certified to ISO 9001. As such, this instrument (including the pump) is ...