Page 2 - Do you need assistance?
Do you need assistance? We are here to help. Call 1-800-468-1502.
Page 3 - Identify System Type
Non-programmable Thermostat RTH111 1 This thermostat is compatible with the followingsystems: • Gas, oil or electric furnace • Central air conditioner • Hot water system with or without pump • Millivolt system • Central heating and cooling system • Heat pump without auxiliary/backup heat Identify ...
Page 4 - Turn power off at the heating/cooling system.; Remove Old Thermostat; Do not remove wallplate yet.
Quick Installation Guide 2 1) Turn power off at the heating/cooling system. 2) Remove old thermostat, but leave wallplate with wires attached. MERCURY NOTICE : Do not put your old thermostat in the trash if it contains mercury in asealed tube. Contact your local wastemanagement authority for instruc...
Page 5 - Identify Wires
Non-programmable Thermostat RTH111 3 If any wires are not attached to your old thermostat or areattached to a terminal marked C or C1 , they will not be connected to your new thermostat. Wrap the bare metal endof each of these wires with electrical tape, so it cannot touchand short other wires. Disc...
Page 6 - NOTE; Mount New Wallplate; Figure 1
Quick Installation Guide 4 1) Loosen the locking screw at the bottom of the thermostat. Note that the screw is captive and cannot be removed from the wallplate. 2) Separate the thermostat from the wallplate as per Figure 1. 3) Position the wallplate against the wall and mark hole positions with a pe...
Page 7 - Typical Wiring; Push any excess wire back into the wall opening.; Connect Wires
Non-programmable Thermostat RTH111 5 Typical Wiring 1) Match each labeled wire with the terminal having the same letter. 2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws. 3) Push any excess wire back into the wall opening. Connect Wires 5. Labels don’t m...
Page 8 - Alternate Wiring
Quick Installation Guide 6 Alternate Wiring If a labeled wire does not match any terminaldesignation, see diagram below. Do not use C, C1 or X wire. Do not use B wire if you alreadyhave O wire. Wrap bare end of wire with electrical tape. This thermostat cannot be used if your old thermostat hadany t...
Page 9 - Incorrect jumper setting; : An incorrect setting is; Set Heating Fan Control; HG
Non-programmable Thermostat RTH111 7 Set jumper JP1, on the back of the thermostat, if youhave connected a wire to the G terminal. Incorrect jumper setting : An incorrect setting is noticeable in a gas or oil heating system. When heatingstarts, you will initially feel cold air coming out of the vent...
Page 10 - : The heat pump operation; Set Heat Pump Reversing Valve
Quick Installation Guide 8 Set jumper JP2, on the back of the thermostat, if youhave a heat pump. Incorrect jumper setting : The heat pump operation will be reversed, i.e., it will cool in Heat mode and willheat in Cool mode. Set Heat Pump Reversing Valve 7. O Leave the jumper in this factory-set ...
Page 11 - Install Batteries and Thermostat
Non-programmable Thermostat RTH111 9 1) Install 2 AAA batteries on the back of the thermostat. 2) Align the two brackets on the top of the thermostat with the corresponding slots on the top of the wallplate. 3) Push the thermostat against the wallplate. 4) Tighten the screw at the bottom of the ther...
Page 12 - System Setup
Quick Installation Guide 10 Follow the procedure below to personalize andconfigure the thermostat according to the heating/cooling system. 1) Press the Up and Down buttons simultaneously (for three seconds) until the display appears as shown below. See table on the next page. 2) Press the Up or Down...
Page 14 - Automation and Control Systems
Automation and Control Systems Honeywell International Inc.1985 Douglas Drive NorthGolden Valley, MN 55422 Honeywell Limited35 Dynamic DriveScarborough, Ontario M1V 4Z9 http://DIYthermostats.honeywell.com Printed in U.S.A.69-2384ES—01 09-09
Page 15 - Guía de instalación rápida
69-2384ES-01 Guía de instalación rápida RTH111 Termostato no programable
Page 16 - LLame al
¿Necesita ayuda?¡Aquí estamos! LLame al 1-800-468-1502
Page 17 - Identificar el tipo de sistema
Termostato no programable RTH111 1 Este termostato es compatible con los siguientessistemas: • Calefactor a gas, aceite o eléctrico • Aire acondicionado central • Sistema de agua caliente con o sin bomba • Sistema de milivoltios • Calefacción y aire acondicionado centrales • Bomba de calor sin calef...
Page 18 - Retirar el viejo termostato; No retirar la placa mural todavía.
Guía de instalación rápida 2 1) Cortar la electricidad del sistema de calefacción/aire acondicionado. 2) Retirar el viejo termostato pero dejar la placa mural con los cables conectados. ADVERTENCIA SOBRE EL MERCURIO No arrojar el viejo termostato a la basura si contienemercurio en un tubo sellado. C...
Page 19 - Identificar los cables
Termostato no programable RTH111 3 Si en el viejo termostato hubiera cables no conectados oconectados a un terminal marcado C o C1 , estos cables no se usarán con el nuevo termostato. Recubrir el extremo demetal desnudo de cada uno con cinta aisladora para que nopuedan tocarse y producir un corto ci...
Page 20 - Instalar la nueva placa mural; Figura 1
Guía de instalación rápida 4 1) Aflojar los tornillos de la base del termostato. El tornillo está cautivo y no se lo puede retirar de la base . 2) Separar el termostato de la placa mural como se indica en la Figura 1. 3) Colocar la placa mural contra la pared y marcar la posición de los agujeros con...
Page 21 - Conexión típica; Conectar los cables
Termostato no programable RTH111 5 Conexión típica 1) Hacer coincidir cada cable etiquetado con el terminal de la misma letra. 2) Aflojar los tornillos del terminal con un destornillador, introducir los cables y reajustar los tornillos. 3) Empujar el exceso de cables en el agujero de la pared. Con...
Page 22 - Conexión alternativa
Guía de instalación rápida 6 Conexión alternativa Si un cable etiquetado no coincide con la designaciónde ningún terminal, referirse al siguiente diagrama: No usar los cables C, C1 o X. No usar el cable B si ya existeun cable O. Envolver el extremo desnudo de los cables concinta aisladora. No puede ...
Page 23 - Ajuste incorrecto del puente:; un ajuste incorrecto es
Termostato no programable RTH111 7 Ajustar el puente JP1, en la parte de atrás del termos-tato, si se conectó un cable al terminal G. Ajuste incorrecto del puente: un ajuste incorrecto es evidente en un sistema a gas o a aceite. Cuando lacalefacción se encienda saldrá aire frío de las rejillas,puest...
Page 24 - el funcionamiento de; Ajuste de la válvula de inversión
Guía de instalación rápida 8 Ajustar el puente JP2, en la parte de atrás del termos-tato, en el caso de una bomba de calor. Ajuste incorrecto del puente: el funcionamiento de la bomba de calor estará invertido: por ejemplo,enfriará en Modo Calefacción y calentará en ModoEnfriamiento. Ajuste de la ...
Page 26 - Configuración del sistema
Guía de instalación rápida 10 El procedimiento a continuación permite personalizar yconfigurar el termostato según el sistema decalefacción/enfriamiento . 1) Presionar los botones Arriba y Abajo al mismo tiempo (3 seg.) hasta que se vea lo que se indica en la ilustración. Ver el cuadro en la página ...
Page 28 - Sistemas para automatización y control
Sistemas para automatización y control Honeywell International Inc.1985 Douglas Drive NorthGolden Valley, MN 55422 Honeywell Limited35 Dynamic DriveScarborough, Ontario M1V 4Z9 http://DIYthermostats.honeywell.com Impreso en EE.UU.69-2384ES—01 09-09