Honeywell T8024D- Manuals

Page 2 - IMPORTANT; Temperature Adjustment:; Setpoint temperature is adjusted by using the; Temperature Setting Range:; available in Premier White¤ and Taupe finish.

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 2 ORDERING INFORMATION When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to theTRADELINE® Catalog or price sheets for complete ordering number. If you have additional questions, ne...

Page 3 - INSTALLATION; When Installing this Product...; CAUTION; Location; Mounting Wallplate to Wall

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 3 INSTALLATION When Installing this Product… 1. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardouscondition. 2. Check the ratings given in the instructions and on the product to make sur...

Page 4 - Wiring; system with two transformers.

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 4 M12202 WALL WALL ANCHORS (2) WALLPLATE MOUNTING SCREWS (2) Fig. 3. Mounting wallplate to wall. Wiring IMPORTANT Use an 18-gauge maximum wire for wiring thethermostats. All wiring must comply with local electrical codes andordinances. Dis...

Page 5 - zone 1 MABS II Mastertrol control panel.

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 5 L1(HOT) L2 M12561 FANRELAY T8000C THERMOSTAT COMPRESSORCONTACTOR TRANSFORMER COOLDAMPER 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOADPROTECTION AS REQUIRED. CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEATPUMP SYSTEMS. JUMPE...

Page 6 - Mounting Thermostat to Wallplate; Setting

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 6 Fig. 11. T8024D multistage heat/cool wiring diagram. Setting Fan Operation (Fuel) Switch The fan operation (fuel) switch is preset at the factory in the Fposition. See Fig. 11. This is the correct setting for mostsystems. If this system ...

Page 7 - Optional System Checkout; Table 1. Heating Cycle Rates

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 7 Optional System Checkout When in steps 1c and 1d only, pressing the ▼ key can be used to turn heat or cool outputs on and off. Change theSYSTEM switch setting to test heat or cool outputs. Noaction takes place If the system switch is in ...

Page 8 - OPERATION; Setting FAN and SYSTEM Switches; Table 2. Preprogrammed Time and Temperature Settings.; FAN Switch; PROGRAMMING; Setting the Weekday Program; P e r i o d; Wake

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 8 OPERATION Setting FAN and SYSTEM Switches Fan and system settings are controlled manually by using theswitches located at the bottom of the thermostat case. SeeFig. 14. Setting the Current Time and Day 1. To Set Current Time.a. Press Sel...

Page 9 - Temporary Temperature Hold; CHECKOUT; Heating

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 9 6. SLEEP a. Press Select.Press ▲ or ▼ to set SLEEP time. b. Press Select.Press ▲ or ▼ to set SLEEP temperature. Setting the Weekend Program 7. WAKE a. Press Select.Press ▲ or ▼ to set WAKE time. b. Press Select.Press ▲ or ▼ to set WAKE t...

Page 10 - Cooling; Press the; Fan

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 10 L1 (HOT) L2 1 L1 (HOT) L2 1 1 2 2 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. FACTORY INSTALLED JUMPER. SYSTEM SWITCH FANSWITCH HEAT OFF COOL O G RC B R W Y FAN RELAY M11730 THERMOSTAT WALLPLATE SYSTEM CO...

Page 11 - FAN Switch Settings; Sequence of Operations; indicates the

T8000C, T8001C AND T8024D PROGRAMMABLE THERMOSTATS 68-0195–2 11 L1 (HOT) L2 1 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. SYSTEM SWITCH FANSWITCH HEAT OFF COOL O G B R W Y FAN RELAY M11731 THERMOSTAT WALLPLATE SYSTEM COMPONENTS HEAT RELAY HEAT CHANGEOVER RELAY COOL ...