Honeywell SERIES COMMUNICATING TB7600- Manuals

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 5 62-2016—01 Fig. 5. Screw terminal arrangement NOTES: — If auxiliary output is used to toggle occupancy of the electronic control card inside the equipment, configure the relay parameter ( Aux cont) to the N.O. setting. A second relay can be add...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 62-2016—01 6 Detailed Wiring Diagrams for Selected Models Fig. 6. TB7656B5x00(x) 2 Heat/2 Cool/Economizer/Programmable Fig. 7. TB7652H5x00(x) Heat pump/Programmable Sensor Wiring for all Thermostat Models Remote mount outdoor temperature sensors ...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 7 62-2016—01 Fig. 8. Wiring example of single remote wall mounted room sensor Fig. 9. Wiring examples of two remote wall mounted room sensors for averaging applications Fig. 10. Wiring examples of three remote wall mounted room sensors for averag...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 62-2016—01 8 THERMOSTAT USER INTERFACE The thermostat features a two-line, eight-character display. There is a low-level backlit level that is always active and can only be seen at night. To turn on the back light to high level, press any key on ...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 9 62-2016—01 User menu flow chart NOTE: Prompts may not all be present depending on model selected User Control Options The TB7600 Series thermostat features an intuitive, menu-driven, back-lit LCD display that walks users through the programming...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 11 62-2016—01 Table 7. Permanent Temperature Setpoint Changes User Menu Sequence SYSTEM MODE SETTING This menu is accessed to set system mode operation. Use to set value, Yes key to confirm. • Sys mode auto : Automatic changeover mode between hea...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 62-2016—01 12 Table 9. Example 1 - Office building closed all weekend * Programming consecutive events to the same time will cause the thermostat to choose the last event as the time at which it will set its schedule. In the above example, the th...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 62-2016—01 14 INSTALLER CONFIGURATION PARAMETER MENU This section describes the parameters available for TB7600 Series thermostat configuration. The TB7600 Series can be programmed at the thermostat or through WEBStation-AX, with the following ex...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 15 62-2016—01 Get From Get From another thermostat configuration utilityDefault value = 255 Range is: 0-254 Conditional parameter to wireless models (TB76xxX5x14W) This parameter is only available for wireless thermostats. This parameter lets you...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 62-2016—01 16 Pwr del Power-up delayDefault value = 10 seconds On initial power up of the thermostat (each time 24 Vac power supply is removed and re-applied) there is a delay before any operation is authorized (fan, cooling or heating). This can...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 19 62-2016—01 NOTE: For Heat Pump models: When the outside air sensor is not connected or is shorted, the thermostat bypasses the heating/cooling lockouts and the low/high balance points. Also heat pump models, when set in Emergency system mode, ...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 62-2016—01 20 Table 17. Additional Configuration Parameters for Economizer Models Configuration parameters Significance Default value Adjustments Chngstpt Changeover setpointDefault value = 55 F (13.0 C) In Cooling mode. The outside air temperatu...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 21 62-2016—01 Table 18. Troubleshooting Guide for all Models Symptom Possible Cause Corrective Action No display on the thermostat Absent or incorrect supply voltage Check power supply voltage between C and RC to be from 19-30 VacCheck for trippe...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 62-2016—01 22 Table 19. Troubleshooting Guide for Heat Pump Models Symptom Possible Cause Corrective Action Auxiliary heat does not operate Wrong mode selected Select emergency heat mode Thermostat in Unoccupied mode Select Occupied Hold in Sched...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS 23 62-2016—01 SPECIFICATIONS Network Protocol: Models available in BACnet MS/TP or ZigBee wireless mesh WEBs-AX Controllers: Compatible with WEB-2xx, WEB-6xx, and WEB-7xx Platform: WEB-2xx and WEB-6xx - WEBStation-AX 3.0 or laterWEB-7xx - WEBStat...

TB7600 SERIES COMMUNICATING RTU/HEAT PUMP THERMOSTATS Automation and Control Solutions Honeywell International Inc.1985 Douglas Drive NorthGolden Valley, MN 55422customer.honeywell.com ® U.S. Registered Trademark© 2011 Honeywell International Inc.62-2016—01 C.L. 04-11 Printed in United States Fig. 1...