Honeywell PVB4024S - Manuals

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 5 63-2689—05 IMPORTANT Special precautions must be taken for dampers that open in a CCW direction. The actuator is shipped with its rotation direction set to CW to Open, which applies to the damper direction in steps 1 and 2 above. If the damper shaft rotates...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 63-2689—05 6 Panel Mounting The controller enclosure is constructed of a plastic base plate and a plastic factory-snap-on cover. NOTE: The controller is designed so that the cover does not need to be removed from the base plate for either mounting or wiring. ...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 7 63-2689—05 The application engineer must review the control job requirements. This includes the sequences of operation for the controller, and for the system as a whole. Usually, there are variables that must be passed between the controller and other Spyde...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 63-2689—05 8 required and thereby affect transformer sizing. The following example is an I x R line-loss calculation for a 200 ft. (61m) run from the transformer to a controller drawing 37 VA and using two 18 AWG (1.0 sq mm) wires. The formula is: Loss = [len...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 9 63-2689—05 on page 6. The earth ground terminal (terminal 3) must be connected to a verified earth ground for each controller in the group (see Fig. 12 on page 9). — All loads on the controller must be powered by the same transformer that powers the control...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 63-2689—05 10 Cabling should be selected that meets or exceeds the BACnet Standard which specifies the following: An MS/TP EIA-485 network shall use shielded, twisted-pair cable with characteristic impedance between 100 and 130 ohms. Distributed capacitance b...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 11 63-2689—05 Fig. 13. Termination modules. Wiring Method WARNING Electrical Shock Hazard. Can cause severe injury, death or property damage. Disconnect power supply before beginning wiring, or making wiring connections, to prevent electrical shock or equipme...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 63-2689—05 12 Table 7. Description of wiring terminal connections for PUB6438S, PVB6436AS, and PVB6438NS. IMPORTANT If the controller is not connected to a good earth ground, the controller's internal transient protection circuitry is compromised and the func...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 15 63-2689—05 Fig. 18. Controller wiring diagram (model PUB6438S shown) for typical PWM reheat and PWM peripheral heat valve actuator. (For note 2, refer to Fig. 14.) NOTE: Make sure to set the Configuration DIP Switch as shown in Fig. 18. Switches 1 through ...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 19 63-2689—05 Fig. 22. Controller wiring diagram (model PUB6438S shown) for RP7517B pneumatic transducer. CHECKOUT Step 1. Check Installation and Wiring Inspect all wiring connections at the controller terminals, and verify compliance with installation wiring...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 63-2689—05 20 Table 8. Status LED States. BACNET STATUS LED: The LED on the front of the controller, between the BACnet MS/TP terminals and MAC Address DIP Switches, provides a visual indication of the BACnet MS/TP communication status. When the controller re...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS 21 63-2689—05 2. Once the terminal block is raised 1/4 in. (6.35 mm) from its alignment pins, grasp the terminal block at its center (for long terminal blocks grasp it at each end) and pull it straight up. Controller Replacement (PVB0000AS, PVB4022AS and PVB6...

SPYDER® BACNET® PROGRAMMABLE CONTROLLERS Automation and Control Solutions Honeywell International Inc.1985 Douglas Drive NorthGolden Valley, MN 55422customer.honeywell.com ® U.S. Registered Trademark© 2012 Honeywell International Inc.63-2689—05 M.S. Rev. 01-12 Printed in United States BACnet ® is a ...