Honeywell NETAXS-123- Manuals

NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A vii L IST OF T ABLES Table 1: Supervised Input Terminal Blocks ................................................................................ 5 Table 2: Supervised Tamper Terminal Blocks ...............................

2 www.honeywell.com Installing the NetAXS-123 Panels Introduction 1.0 Introduction This document describes how to install the NetAXS-123 Standard Enclosure access control unit and the NetAXS-123 Compact Enclosure access control unit. 1.1 Access Control Overview An access control system protects and ...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 3 2.0 Panel Components and Descriptions Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 5 Figure 3: NetAXS-123 Add-On Board Wiring and Components 2.1 Supervised Input Wiring The supervised inputs are located on the following terminal bloc...

6 www.honeywell.com Installing the NetAXS-123 Panels Panel Components and Descriptions Tampers can also be supervised. They are located on the following terminal blocks: Table 2: Supervised Tamper Terminal Blocks Door Status (STS) and Request to Exit (REX) for all three doors may be configured for N...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 7 Caution: The system has not been verified for compliance with UL1076 Burglar Alarm units and systems. 2.2 NetAXS-123 Access Control Unit The NetAXS-...

8 www.honeywell.com Installing the NetAXS-123 Panels Panel Components and Descriptions 2.2.2 Supported Readers Supported readers include the following: Table 4: Readers Supported by NetAXS-123 Series Reader Model Honeywell Part Number OmniProx OP-10 OP10GENE OP10HONE OP-30 OP30GENE OP30HONE OP-40 OP...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 9 Note: For NetAXS-123 reader specifications, see Hardware Specifications , page 60. 2.2.3 Real-Time Clock Protection The panel RTC is backed up using...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 11 3.0 Installation 3.1 Installing the Compact Enclosure Panel Perform the following steps to install the NetAXS-123 Compact panel: Warning: Use a static strap whenever to...

12 www.honeywell.com Installing the NetAXS-123 Panels Installation 3. Mount the board onto the back of the panel. 4. Choose the tamper type (standard or off-the-wall tamper) and wire the tamper. • Wiring a standard tamper:

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 13 • Wiring an off-the-wall tamper: 5. Set the tamper, using pliers at the four locations indicated below. Warning: Do not apply power at this time.

14 www.honeywell.com Installing the NetAXS-123 Panels Installation 6. Connect the Ethernet cable and the Tamper wire, as shown below. 7. Set DIP switch settings for the panel address, communication termination and biasing. See DIP Switch Settings , page 36. 8. Check all wiring at this time. Caution:...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 15 3.1.2 Installing over a Gang Box 1. Review the panel layout, cable runs, and power needs. 2. Mount the back of the panel on the gang box. 3. Pull the wires from the gan...

16 www.honeywell.com Installing the NetAXS-123 Panels Installation 3.1.3 Installing on a Flat Surface 1. Review the panel layout, cable runs, and power needs. 2. Mount the back of the enclosure on the surface, either with drywall screes or threaded wall anchors. 3. Break off the appropriate plastic ...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 17 3.2 Installing the Standard Enclosure Panel Perform the following steps to install the NetAXS-123 Standard Enclosure panel: Warning: Use a static strap whenever touchin...

18 www.honeywell.com Installing the NetAXS-123 Panels Installation 3. Install the power supply. a. Fit the power supply screws through the key holes in the left side of the cabinet, and seat the power supply by pulling down. b. From the outside of the cabinet, tighten the screws to lock the power su...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 19 c. Inside the cabinet, screw in the two self-tapping screws (supplied in the product box) at the top and bottom of the power supply. Warning: These screws must be insta...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 21 4. Select one of the following three possible entry points for the power cable: Warning: Do not apply power at this time. Be sure the power cable is disconnected from t...

22 www.honeywell.com Installing the NetAXS-123 Panels Installation 5. Use a pencil to mark the location of the holes on the wall. 6. Screw the NetAXS-123 Controller Board with the four captive screws

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 23 7. Hold the Add-On Board over the Controller Board and seat the board-to-board connector into the Controller Board. Secure the Add-On Board onto the Controller Board wi...

24 www.honeywell.com Installing the NetAXS-123 Panels Installation 8. Connect the wiring harness, as shown. Warning: DO NOT CONNECT the AC power or the battery wires yet! 9. Power up the NetAXS-123 Controller Board and configure the system. Refer to the NetAXS-123 Startup Guide (800-05780) for instr...

26 www.honeywell.com Installing the NetAXS-123 Panels Installation 3.3 Installing the Add-On Board Warning: To prevent damage to the NXC1 Controller Board, remove power from the NetAXS-123 panel before installing or removing a NetAXS-123 Add-On Board. 1. On the NetAXS-123 Controller Board, locate th...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 27 2. Pick up the Add-On Board and notice the four posts on the bottom. 3. Seat the Add-On Board posts into the four posts on the NetAXS-123 Controller Board, aligning the...

28 www.honeywell.com Installing the NetAXS-123 Panels Installation 5. Set the relay jumpers. a. Use the following figure to locate the jumpers. b. See Add-On Board DIP Switch and Jumper Settings , page 40, to set the power source (12VDC power or external power) and the relay contact position (Normal...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 29 3.4 Wiring the Readers Each reader port supports one or two readers (entry and exit readers) with Wiegand output format. The maximum power draw is 500 mA for readers an...

30 www.honeywell.com Installing the NetAXS-123 Panels Installation Table 5 shows the input/output factory default wiring for a one-door configuration on the Controller Board. Table 5: Factory Default Configuration Settings for Door 1 a Readers A and B share the same connection. Type Purpose Web Defa...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 31 Notes : • The Controller Board includes Inputs 7 and 8 but they are reserved for system use. • The Controller Board also includes Output 5, a general-purpose output, an...

32 www.honeywell.com Installing the NetAXS-123 Panels Installation Table 7 lists the factory Add-On Board default settings for a door 3. These mappings should be used for the readers, inputs, and outputs when either a 1- or 2-door Add-On Board is attached to the board-to-board connector on the contr...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 33 • NetAXS-123 supports a variety of Wiegand reader models. Some readers have only one brown wire for LED control; others have two possible LED control inputs--orange for...

34 www.honeywell.com Installing the NetAXS-123 Panels Installation 2. Use the following figure to wire the door strike/mag lock according to the power supply used. Be sure to use the S4 suppressor kits as shown below. Notes: • As shown in the illustration above, the Dry C terminal for the On-Board o...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 35 3.6 Setting DIP Switches and Jumpers 3.6.1 Controller Board DIP Switch and Jumper Settings Figure 6 locates the NetAXS-123 DIP switch panel and the output 1 and output ...

36 www.honeywell.com Installing the NetAXS-123 Panels Installation DIP Switch Settings Use the following DIP switch configurations to set the panel address. Table 8: NetAXS-123 SW1 DIP Switch Settings S1 S2 S3 S4 S5 S6 S7 a S8 b S9 b S10 Selection ON OFF OFF OFF OFF Address 1 (default) OFF ON OFF OF...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 37 OFF ON ON OFF ON Address 22 ON ON ON OFF ON Address 23 OFF OFF OFF ON ON Address 24 ON OFF OFF ON ON Address 25 OFF ON OFF ON ON Address 26 ON ON OFF ON ON Address 27 O...

38 www.honeywell.com Installing the NetAXS-123 Panels Installation Note: Address 0 is not a valid setting. b. Both DIP Switch 8 and DIP Switch 9 need to be either ON or OFF to be properly configured. Table 9: NetAXS-123 SW2 DIP Switch Settings S1 a S2 a Selection OFF OFF RS-485_2 termination (EOL) D...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 39 Jumper Settings The NetAXS-123 Controller Board provides two jumper sets, one each for output relay 1 and output relay 3. Each relay has two 3-pin jumpers associated wi...

40 www.honeywell.com Installing the NetAXS-123 Panels Installation Note: The power source selected by the jumper settings shown above configure the power source for the relay. It does not configure the power source for the panel. • Setting the jumpers to configure the relay contact type: 3.6.2 Add-O...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 41 used to select Normally Open (NO) or Normally Closed (NC) relay contacts. There is a total of four 3-pin jumpers (two per relay) on the controller board. • Setting the ...

42 www.honeywell.com Installing the NetAXS-123 Panels Installation 3.7 Communications 3.7.1 USB Communications The NetAXS-123 Controller Board provides a version 2.0 USB port that connects to the web browser or to a WIN-PAK host. The following figure identifies the location of the port on the board....

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 43 2. Click Install USB Drivers on the product menu to start the USB driver installation wizard. 3. Click Next to display the Ready to Install the Program screen. Note: If...

44 www.honeywell.com Installing the NetAXS-123 Panels Installation 5. When the installation is complete, the closing screen appears: 6. Click Finish . 7. Connect the computer to the NetAXS-123 controller with a USB-A to Micro USB-B cable. 8. Turn on the power to the NetAXS-123 controller. For login ...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 47 3.7.3 Ethernet TCP/IP Communications Figure 11: Ethernet TCP/IP Configuration This configuration supports a total of 31 NetAXS and NetAXS-123 panels per Multidrop line....

48 www.honeywell.com Installing the NetAXS-123 Panels System Configuration 4.0 System Configuration This section provides wiring diagrams for each of the NetAXS-123 system configurations. 4.1 Ethernet Connection Figure 12: Ethernet Connection Note: You should ground each NetAXS-123 Standard (Metal) ...

50 www.honeywell.com Installing the NetAXS-123 Panels System Configuration 4.3 RS-485 Connection via PCI-3 This connection supports thirty-one NetAXS-123 panels for each drop line. Note that PCI-3 units can also be wired in interior, as well as in endpoint, positions. See Figure 16 on page 52 and Fi...

Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 55 4.7 Fiber Converter to RS-485 Connection via PCI-3 This connection supports 31 NetAXS-123 panels for each drop line. Figure 19: Fiber Converter to RS-485 Connec...

60 www.honeywell.com Installing the NetAXS-123 Panels Hardware Specifications 5.0 Hardware Specifications The specifications in this section apply to both the Standard Enclosure and Compact Enclosure panels. 5.1 Relay Contacts Maximum of six Form-C SPDT relays, 3A (at dry contact) or 0.5A (at self-w...

Installing the NetAXS-123 Panels Hardware Specifications NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 61 Example : If the total current consumption of your external devices exceeds the 450mA maximum current maximum, then use one of the following system configura...

62 www.honeywell.com Installing the NetAXS-123 Panels Hardware Specifications 5.6 Environment • Temperature: 0C to 49C operating, -55C to +85C storage.• Humidity: 5% to 85% RHNC. 5.7 Cable Use industry-standard cables that meet the following specifications: Table 10: Reader Wiring Cable Specificatio...

Installing the NetAXS-123 Panels Basic Standalone Operation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 63 6.0 Basic Standalone Operation 6.1 Card Read / Door Lock Operation 1. Present a card to a reader. 2. The reader sends the card number to a reader input on...

64 www.honeywell.com Installing the NetAXS-123 Panels Maintenance 7.0 Maintenance Perform the following maintenance on the NetAXS-123 enclosure: • Change the backup battery every two to two-and-a-half years.• Oil the lock once per year.• Use the following procedure to change the 1A, 250V, Bussan typ...

Installing the NetAXS-123 Panels Troubleshooting NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 65 8.0 Troubleshooting Note: The NetAXS-123 EOL network is AC-coupled. There is no resistance difference between the RS-485 positive and negative terminals if the EOL n...

66 www.honeywell.com Installing the NetAXS-123 Panels Technical Support 9.0 Technical Support 9.1 Normal Support Hours Monday through Friday, 7:00 a.m. to 7:00 p.m. Central Standard Time (CST), except company holidays: (800) 323-4576. 9.2 Web For technical assistance please visit http://www.honeywel...

Installing the NetAXS-123 Panels Technical Support NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 67 This page is left blank for printing purposes.

Honeywell Access Systems 135 W. Forest Hill AvenueOak Creek, WI 53154United States800-323-4576414-766-1798 Faxwww.honeywellaccess.com Specifications subject to changewithout notice. © Honeywell. All rights reserved. Document 800-05799, Revision A

NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A vii L IST OF T ABLES Table 1: Supervised Input Terminal Blocks ................................................................................ 5 Table 2: Supervised Tamper Terminal Blocks ...............................

2 www.honeywell.com Installing the NetAXS-123 Panels Introduction 1.0 Introduction This document describes how to install the NetAXS-123 Standard Enclosure access control unit and the NetAXS-123 Compact Enclosure access control unit. 1.1 Access Control Overview An access control system protects and ...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 3 2.0 Panel Components and Descriptions Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 5 Figure 3: NetAXS-123 Add-On Board Wiring and Components 2.1 Supervised Input Wiring The supervised inputs are located on the following terminal bloc...

6 www.honeywell.com Installing the NetAXS-123 Panels Panel Components and Descriptions Tampers can also be supervised. They are located on the following terminal blocks: Table 2: Supervised Tamper Terminal Blocks Door Status (STS) and Request to Exit (REX) for all three doors may be configured for N...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 7 Caution: The system has not been verified for compliance with UL1076 Burglar Alarm units and systems. 2.2 NetAXS-123 Access Control Unit The NetAXS-...

8 www.honeywell.com Installing the NetAXS-123 Panels Panel Components and Descriptions 2.2.2 Supported Readers Supported readers include the following: Table 4: Readers Supported by NetAXS-123 Series Reader Model Honeywell Part Number OmniProx OP-10 OP10GENE OP10HONE OP-30 OP30GENE OP30HONE OP-40 OP...

Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 9 Note: For NetAXS-123 reader specifications, see Hardware Specifications , page 60. 2.2.3 Real-Time Clock Protection The panel RTC is backed up using...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 11 3.0 Installation 3.1 Installing the Compact Enclosure Panel Perform the following steps to install the NetAXS-123 Compact panel: Warning: Use a static strap whenever to...

12 www.honeywell.com Installing the NetAXS-123 Panels Installation 3. Mount the board onto the back of the panel. 4. Choose the tamper type (standard or off-the-wall tamper) and wire the tamper. • Wiring a standard tamper:

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 13 • Wiring an off-the-wall tamper: 5. Set the tamper, using pliers at the four locations indicated below. Warning: Do not apply power at this time.

14 www.honeywell.com Installing the NetAXS-123 Panels Installation 6. Connect the Ethernet cable and the Tamper wire, as shown below. 7. Set DIP switch settings for the panel address, communication termination and biasing. See DIP Switch Settings , page 36. 8. Check all wiring at this time. Caution:...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 15 3.1.2 Installing over a Gang Box 1. Review the panel layout, cable runs, and power needs. 2. Mount the back of the panel on the gang box. 3. Pull the wires from the gan...

16 www.honeywell.com Installing the NetAXS-123 Panels Installation 3.1.3 Installing on a Flat Surface 1. Review the panel layout, cable runs, and power needs. 2. Mount the back of the enclosure on the surface, either with drywall screes or threaded wall anchors. 3. Break off the appropriate plastic ...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 17 3.2 Installing the Standard Enclosure Panel Perform the following steps to install the NetAXS-123 Standard Enclosure panel: Warning: Use a static strap whenever touchin...

18 www.honeywell.com Installing the NetAXS-123 Panels Installation 3. Install the power supply. a. Fit the power supply screws through the key holes in the left side of the cabinet, and seat the power supply by pulling down. b. From the outside of the cabinet, tighten the screws to lock the power su...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 19 c. Inside the cabinet, screw in the two self-tapping screws (supplied in the product box) at the top and bottom of the power supply. Warning: These screws must be insta...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 21 4. Select one of the following three possible entry points for the power cable: Warning: Do not apply power at this time. Be sure the power cable is disconnected from t...

22 www.honeywell.com Installing the NetAXS-123 Panels Installation 5. Use a pencil to mark the location of the holes on the wall. 6. Screw the NetAXS-123 Controller Board with the four captive screws

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 23 7. Hold the Add-On Board over the Controller Board and seat the board-to-board connector into the Controller Board. Secure the Add-On Board onto the Controller Board wi...

24 www.honeywell.com Installing the NetAXS-123 Panels Installation 8. Connect the wiring harness, as shown. Warning: DO NOT CONNECT the AC power or the battery wires yet! 9. Power up the NetAXS-123 Controller Board and configure the system. Refer to the NetAXS-123 Startup Guide (800-05780) for instr...

26 www.honeywell.com Installing the NetAXS-123 Panels Installation 3.3 Installing the Add-On Board Warning: To prevent damage to the NXC1 Controller Board, remove power from the NetAXS-123 panel before installing or removing a NetAXS-123 Add-On Board. 1. On the NetAXS-123 Controller Board, locate th...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 27 2. Pick up the Add-On Board and notice the four posts on the bottom. 3. Seat the Add-On Board posts into the four posts on the NetAXS-123 Controller Board, aligning the...

28 www.honeywell.com Installing the NetAXS-123 Panels Installation 5. Set the relay jumpers. a. Use the following figure to locate the jumpers. b. See Add-On Board DIP Switch and Jumper Settings , page 40, to set the power source (12VDC power or external power) and the relay contact position (Normal...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 29 3.4 Wiring the Readers Each reader port supports one or two readers (entry and exit readers) with Wiegand output format. The maximum power draw is 500 mA for readers an...

30 www.honeywell.com Installing the NetAXS-123 Panels Installation Table 5 shows the input/output factory default wiring for a one-door configuration on the Controller Board. Table 5: Factory Default Configuration Settings for Door 1 a Readers A and B share the same connection. Type Purpose Web Defa...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 31 Notes : • The Controller Board includes Inputs 7 and 8 but they are reserved for system use. • The Controller Board also includes Output 5, a general-purpose output, an...

32 www.honeywell.com Installing the NetAXS-123 Panels Installation Table 7 lists the factory Add-On Board default settings for a door 3. These mappings should be used for the readers, inputs, and outputs when either a 1- or 2-door Add-On Board is attached to the board-to-board connector on the contr...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 33 • NetAXS-123 supports a variety of Wiegand reader models. Some readers have only one brown wire for LED control; others have two possible LED control inputs--orange for...

34 www.honeywell.com Installing the NetAXS-123 Panels Installation 2. Use the following figure to wire the door strike/mag lock according to the power supply used. Be sure to use the S4 suppressor kits as shown below. Notes: • As shown in the illustration above, the Dry C terminal for the On-Board o...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 35 3.6 Setting DIP Switches and Jumpers 3.6.1 Controller Board DIP Switch and Jumper Settings Figure 6 locates the NetAXS-123 DIP switch panel and the output 1 and output ...

36 www.honeywell.com Installing the NetAXS-123 Panels Installation DIP Switch Settings Use the following DIP switch configurations to set the panel address. Table 8: NetAXS-123 SW1 DIP Switch Settings S1 S2 S3 S4 S5 S6 S7 a S8 b S9 b S10 Selection ON OFF OFF OFF OFF Address 1 (default) OFF ON OFF OF...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 37 OFF ON ON OFF ON Address 22 ON ON ON OFF ON Address 23 OFF OFF OFF ON ON Address 24 ON OFF OFF ON ON Address 25 OFF ON OFF ON ON Address 26 ON ON OFF ON ON Address 27 O...

38 www.honeywell.com Installing the NetAXS-123 Panels Installation Note: Address 0 is not a valid setting. b. Both DIP Switch 8 and DIP Switch 9 need to be either ON or OFF to be properly configured. Table 9: NetAXS-123 SW2 DIP Switch Settings S1 a S2 a Selection OFF OFF RS-485_2 termination (EOL) D...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 39 Jumper Settings The NetAXS-123 Controller Board provides two jumper sets, one each for output relay 1 and output relay 3. Each relay has two 3-pin jumpers associated wi...

40 www.honeywell.com Installing the NetAXS-123 Panels Installation Note: The power source selected by the jumper settings shown above configure the power source for the relay. It does not configure the power source for the panel. • Setting the jumpers to configure the relay contact type: 3.6.2 Add-O...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 41 used to select Normally Open (NO) or Normally Closed (NC) relay contacts. There is a total of four 3-pin jumpers (two per relay) on the controller board. • Setting the ...

42 www.honeywell.com Installing the NetAXS-123 Panels Installation 3.7 Communications 3.7.1 USB Communications The NetAXS-123 Controller Board provides a version 2.0 USB port that connects to the web browser or to a WIN-PAK host. The following figure identifies the location of the port on the board....

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 43 2. Click Install USB Drivers on the product menu to start the USB driver installation wizard. 3. Click Next to display the Ready to Install the Program screen. Note: If...

44 www.honeywell.com Installing the NetAXS-123 Panels Installation 5. When the installation is complete, the closing screen appears: 6. Click Finish . 7. Connect the computer to the NetAXS-123 controller with a USB-A to Micro USB-B cable. 8. Turn on the power to the NetAXS-123 controller. For login ...

Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 47 3.7.3 Ethernet TCP/IP Communications Figure 11: Ethernet TCP/IP Configuration This configuration supports a total of 31 NetAXS and NetAXS-123 panels per Multidrop line....

48 www.honeywell.com Installing the NetAXS-123 Panels System Configuration 4.0 System Configuration This section provides wiring diagrams for each of the NetAXS-123 system configurations. 4.1 Ethernet Connection Figure 12: Ethernet Connection Note: You should ground each NetAXS-123 Standard (Metal) ...

50 www.honeywell.com Installing the NetAXS-123 Panels System Configuration 4.3 RS-485 Connection via PCI-3 This connection supports thirty-one NetAXS-123 panels for each drop line. Note that PCI-3 units can also be wired in interior, as well as in endpoint, positions. See Figure 16 on page 52 and Fi...

Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 55 4.7 Fiber Converter to RS-485 Connection via PCI-3 This connection supports 31 NetAXS-123 panels for each drop line. Figure 19: Fiber Converter to RS-485 Connec...

60 www.honeywell.com Installing the NetAXS-123 Panels Hardware Specifications 5.0 Hardware Specifications The specifications in this section apply to both the Standard Enclosure and Compact Enclosure panels. 5.1 Relay Contacts Maximum of six Form-C SPDT relays, 3A (at dry contact) or 0.5A (at self-w...

Installing the NetAXS-123 Panels Hardware Specifications NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 61 Example : If the total current consumption of your external devices exceeds the 450mA maximum current maximum, then use one of the following system configura...

62 www.honeywell.com Installing the NetAXS-123 Panels Hardware Specifications 5.6 Environment • Temperature: 0C to 49C operating, -55C to +85C storage.• Humidity: 5% to 85% RHNC. 5.7 Cable Use industry-standard cables that meet the following specifications: Table 10: Reader Wiring Cable Specificatio...

Installing the NetAXS-123 Panels Basic Standalone Operation NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 63 6.0 Basic Standalone Operation 6.1 Card Read / Door Lock Operation 1. Present a card to a reader. 2. The reader sends the card number to a reader input on...

64 www.honeywell.com Installing the NetAXS-123 Panels Maintenance 7.0 Maintenance Perform the following maintenance on the NetAXS-123 enclosure: • Change the backup battery every two to two-and-a-half years.• Oil the lock once per year.• Use the following procedure to change the 1A, 250V, Bussan typ...

Installing the NetAXS-123 Panels Troubleshooting NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 65 8.0 Troubleshooting Note: The NetAXS-123 EOL network is AC-coupled. There is no resistance difference between the RS-485 positive and negative terminals if the EOL n...

66 www.honeywell.com Installing the NetAXS-123 Panels Technical Support 9.0 Technical Support 9.1 Normal Support Hours Monday through Friday, 7:00 a.m. to 7:00 p.m. Central Standard Time (CST), except company holidays: (800) 323-4576. 9.2 Web For technical assistance please visit http://www.honeywel...

Installing the NetAXS-123 Panels Technical Support NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 67 This page is left blank for printing purposes.

Honeywell Access Systems 135 W. Forest Hill AvenueOak Creek, WI 53154United States800-323-4576414-766-1798 Faxwww.honeywellaccess.com Specifications subject to changewithout notice. © Honeywell. All rights reserved. Document 800-05799, Revision A