Honeywell KXP2290 - Manuals

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 1-1 SECTION I GENERAL INFORMATION 1.1 INTRODUCTION This manual contains information relative to the physical, mechanical, and electrical characteris-tics of the Honeywell KXP 2290 Mode S Transponder. Installation and check out proce...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 1-2 1.3 TECHNICAL CHARACTERISTICS 1.3.1 KXP 2290 TECHNICAL CHARACTERISTICS 1.3.2 ANTENNA The KXP 2290 will work with any conventional ATCRBS blade or quarter-wave monopole type an-tenna provided it is certified to TSO-C112/ETSO-2C11...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 1-3 1.4 UNITS AND ACCESSORIES SUPPLIED 1.4.1 CONFIGURATIONS AVAILABLE P/N 066-01198-0101 is the only version of the KXP 2290 that is currently available. 1.4.2 KXP 2290 INSTALLATION KIT The KXP 2290 Transponder shares a mounting rac...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 1-4 Shield braids must be clamped to the connector backshell using bar clamp assembly P/N 200-10452-0000 which contains the following parts. See FIGURE 2-2 KXP 2290 INSTALLATION DRAWING and FIGURE 2-3 KXP 2290 BAR CLAMP ASSEMBLY DRA...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 1-5 Use the following parts for installations using FIGURE 2-9 ECS/ECS-RG-400 CABLE CONNEC- TIONS DRAWING . (ECS cable only) Use the following parts for installations using FIGURE 2-9 ECS/ECS-RG-400 CABLE CONNEC- TIONS DRAWING . (EC...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-1 SECTION II INSTALLATION 2.1 GENERAL INFORMATION This section contains suggestions and factors to consider before installing the KXP 2290 Mode S Transponder. Close adherence to these suggestions will assure a more satisfactory pe...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-5 2.3.3.1 Transponder And Mounting Tray Locations The KXP 2290 Mode S Transponder shares a mounting tray with the Honeywell APEX KMC 2210 controller and is part of the APEX cockpit panel configuration. Except for antenna cables th...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-7 2.3.5 CRIMP TOOL INFORMATION The following is a listing of crimp tools and accessories for use with the KXP 2290. * All source tools and positioners are to Mil-Spec Standard and are interchangeable. ** Positioner wire gauge (AWG...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-9 FIGURE 2-1 MAIN CONNECTOR - JKXP2290-1 Front View Pin # I/O Description Specification 1 I +28 Vdc Power In Aircraft Power +18 to +32 Vdc 2 I Ext Standby ~ Discrete input. GND (< 10 ohms-to-ground) on this pin forces the unit ...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-10 NOTE: Do not connect to pins marked “Reserved” as the functionality is for future application. 23 I Ext Ident Reserved 24 I Ext Air/Gnd Reserved 25 I Conc 429 RX - B Concentrated A429 input bus 26 I Spare 4 429 RX - B Reserved ...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2- 11 FIGURE 2-2 KXP 2290 INSTALLATION DRAWING (Dwg. 155-01786-0000 Rev. B, Sheet 1 of 4)

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2- 19 FIGURE 2-3 KXP 2290 BAR CLAMP ASSEMBLY DRAWING (300-10452-0000, Rev. -)

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2- 21 FIGURE 2-4 KA 61 INSTALLATION DRAWING (Sheet 1 of 2)

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2- 25 FIGURE 2-5 KXP 2290 INTERCONNECTION DRAWING (Dwg. 155-0xxxx-000x Rev. -, Sheet 1 of 2)

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2- 27 FIGURE 2-6 KXP 2290 INTERCONNECTION DRAWING (Dwg. 155-0xxxx-000x Rev. -, Sheet 2 of 2)

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2- 29 FIGURE 2-7 RF CONNECTOR DRAWING

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-32 FIGURE 2-9 ECS/ECS-RG-400 CABLE CONNECTIONS DRAWING (Options For Longer Antenna Cable Lengths)

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-33 FIGURE 2-10 CABLE CONNECTOR DRAWING

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-34 FIGURE 2-11 TYPE “N” AND “C” CONNECTOR ASSEMBLY DRAWING PART NUMBER SIZE DIMENSION RG/U CABLE A B C D 024-00075-0000 393 9/32 1/8 5/32 3/64 024-00051-0060 400 9/32 1/8 5/32 3/64

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-35 FIGURE 2-12 BNC CONNECTOR ASSEMBLY DRAWING

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page 2-37 2.4 POST-INSTALLATION CHECKS 2.4.1 TRANSPONDER SYSTEM CHECKOUT The post-installation test is used to apply power and functionally checkout the system. Successful completion of the post-installation test verifies the proper oper...

n KXP 2290 Rev. 0c, June/2006 Preliminary 05/24/06 10689I00.JA Page TSO-1 ENVIRONMENTAL QUALIFICATIONS APPENDIX ENVIRONMENTAL QUALIFICATION FORM(S)