Honeywell IPGSM-DPC - Manuals

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 5 – 4. Connect the LED Display board to its connector, then slide the board into the mounting rails. (Refer to the “ LED Display Information ” topic if a wire is detached from its connector.) 5. Carefully remove the packaging ma...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 6 – IPGSM-DPC-001-V1 TB 1 678 5 1011 9 234 1 FOR EXTERNAL ANTENNA50 OHM MMCX ONLY PRIMARY POWER: 9 - 16.5 VACCURRENT: 900mA PEAK, 70mA STANDBYBATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP FCC:XXXXXXXXXX IC: YYYYYYYYYY RSSI M0 M1 GPRS IB...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 7 – Wiring the 659EN Line Fault Monitor (if required) The IPGSM-DPC is compatible with the Honeywell brand FACP’s listed on page 1 when the model 659EN Line Fault Monitor is installed. 1. Refer to the installation guide for the ...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 8 – STEP 5 – Program the Communications Module You must use the 7720P Programming tool to program the IPGSM-DPC. When using the 7720P Programming tool, the values given below are for most installations. Press the [#] key to acce...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 9 – To exit the programming mode, press [N] in response to the "Review?" prompt. Then press [Y] to the "Exit Prog Mode?" prompt. Upon exiting, the root file is updated to log the changes made. A message is displa...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 10 – Dialer Capture Module Information LED Indicator STATUS RED – Steady ON Messages exist in buffer. RED – Flashing No messages to be sent. Waiting for messages. GREEN – Steady ON Normal Indication. GREEN – Blinks every 2 sec. ...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 11 – PowerBoost1 Module Information LED Indicator STATUS AC (green) AC power available. ACTIVE (green) Cyclical flashing – normal communications. Repetition of 3 flashes – loss of communications. LOW BATT (yellow) Missing or low...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 12 – iGSM Communications Module Information TB 1 67 8 5 1011 9 234 1 PRIMARY POWER: 9 - 16.5 V AC CURRE N T: 900mA PEAK, 70mA STA N DBY BATTERY: 8V . 3.1 AHr FOR 24 Hr BACKUP FCC:XXXXXXXXXX IC: YYYYYYYYYY RSSI M0 M1 GPRS IBS iPG...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 13 – RF Specifications Band Transmission Frequency (MHz) Transmit Power (dBm) Receive Frequency (MHz) Receive Sensitivity (dBm) Number of Channels Channel Spacing (MHz) Duplex Separation (kHz) GSM 850 824-849 33 869-894 -107 124...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 14 – IPGSM-DPC Trouble Detection Information Telco 1 is used for the Fire Panel to output contact ID messages to the IPGSM-DPC, and Telco 2 is used by the IPGSM-DPC to report faults to the Fire Panel. If Telco 1 is not operation...

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide – 15 – NOTES

Wiring Diagram The wiring diagram below is depicted for point-to-point electrical connection checks used for troubleshooting or component replacement. It is not intended to show the physical routing of wires. When replacing a wire or component, ensure the wire is routed in the same manner as the ori...

IC STATEMENT Notice: This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. IC STATEMENT This device complies with RSS 210 of IC. Operation is subject to the following two conditions: (1) This device may not ca...