Honeywell Horizon 7625- Manuals

4 B EFORE I NSTALLING Y OUR MS7600 When mounting the MS7600 or replacingthe Top Plate: D O N OT Press on the window. Figure 2 Lift the Top plate straight up toremove. There is no hardware requiredto remove or replace the topcover. See caution on page 3. There are two installation tabsunder the top c...

5 M OUNTING THE MS7600 S ERIES There are three options for mounting your MS7600. Option “A” uses a shelf to support the unit. Option B lets the unit hang free in the counter top. Option C lets the unit hang free in the counter top with the use of a stainless steel trim ringfor support. The trim ring...

6 M OUNTING THE MS7600 S ERIES O PTION B: Free Hanging Support Figure 8: Package Flow (right) Figure 9: Specifications for free hanging support. Figure 10: Installation Tabs

8 Figure 14: Keyboard WedgeInterfaces I NSTALLATION FOR K EYBOARD W EDGE I NTERFACE 1. Turn off the host system. 2. Disconnect the keyboard from the host. 3. Connect the PowerLink cable to the 2 nd jack from the top of the MS7600. 4. Connect the “Y” end of the PowerLink cable to the keyboardand the ...

10 Figure 17: USB, Interface I NSTALLATION FOR USB I NTERFACE 1. Turn off the host system. 2. Determine if your application requires USB Keyboard communication protocols or USB Point of Sale communication protocols. 3. If you require USB Keyboard communication protocols, skip to step 4. If you requi...

13 I NSTALLATION FOR RS232 OR L IGHT P EN I NTERFACES Step 7, page 12 continued. For RS232 Communication: Scan 1 st ³ 9 9 9 9 9 8 Recall Defaults Scan 2 nd ³ 4 1 5 5 5 4 Enable RS-232 For Light Pen Communication: Scan 1 st ³ 9 9 9 9 9 8 Recall Defaults Scan 2 nd ³ 4 1 5 5 2 4 Enable Light Pen/Wand

15 Figure 13: OCIA, Interface I NSTALLATION FOR OCIA I NTERFACE 1. Turn off the host system. 2. Connect the MVC cable to the 2 nd jack down from the top of the MS7600. 3. Connect the other end of the MVC cable to the host. Before continuing verify that theMVC cable is connected to theappropriate int...

16 I NSTALLATION OF A S ECONDARY S CANNER 1. Turn off the host system. 2. Connect the round end of the PowerLink RS232 AUX cable [ MLPN 54-54667A] to the RS232 jack of the secondary scanner ( see figure 20 ). 3. Connect the other end of the PowerLink RS232 AUX cable into the 3 rd jack down from the ...

17 I NSTALLATION OF A S ECONDARY S CANNER 11. Scan the following bar code to configure the auxiliary port on the MS7600 to accept a Metrologic scanner as the secondary scanner. The following bar codes do not apply when using an MS6720 as a secondary scanner. Contact a Metrologic representative forad...

19 S CANNER P ARTS Figure 21: Scanner Parts n Output Window (Laser Aperture) o Amber LED (Located Under Window) p Red LED (Located Under Window) q Speaker r Cable Connection Area s Stainless Steel Top (MS7625 units only) t Package Flow Indicator Arrow Head u Rubber Connector Plug v EAS Deactivation ...

20 M AINTENANCE Smudges and dirt can interfere with the proper scanning of a bar code.Therefore, the output window will need occasional cleaning. For the MS7600 glass window: 1. Spray glass cleaner onto lint free, non-abrasive cleaning cloth.2. Gently wipe the scanner window. For the MS7600 red wind...

21 S CANNER L ABELS Each scanner has a label on the bottom of the unit. The label containsinformation such as the model number, date of manufacture, serial number, andcaution information. An additional caution label is located under the top plate.The following are examples of these labels. Figure 23...

22 A UDIBLE I NDICATORS When the MS7600 scanner is in operation, it provides audible feedback. Thesesounds indicate the status of the scanner. Eight settings are available for thetone of the beep (normal, 6 alternate tones and no tone) plus three volumesettings. To change the tone or volume, refer t...

23 V ISUAL I NDICATORS There is a red LED and amber LED onthe front of the MS7600. When the scanner ison, the flashing or constant illumination of theLEDs indicates the status of the current scanand the scanner. Figure 24: LEDs No Red or Amber LED The LEDs will not be illuminated if the scanner isno...

25 C HANGING THE B EEPER T ONE & V OLUME Changing the Beeper Tone Beeper tones may be programmed directly or incrementally using the followingbar code. The new tone will be heard followed by a short pause. Two more newtones will be heard signifying the new setting has been stored in memory. Thes...

26 P OWER S AVE M ODES AND IR D ETECTION The MS7600 has five programmable power save modes. Refer to the MetroSelect Programming Guide for additional information on Power Save Modes. 1. Blink Power Save Mode: Blinks the laser OFF & ON after a programmed period of non-use. When the scanner recogn...

27 P OWER S AVE M ODES AND IR D ETECTION Figure 27: IR Activation Area Parallel to Package Flow Specifications are subject to change without notice.

28 S CAN V OLUME S PECIFICATIONS (B ASED ON 100% UPC B AR C ODES ) Figure 28: Scan Volume in Plane Perpendicular to Flow Figure 29: Scan Volume in Plane Parallel to Flow Specifications subject to change without notice.

29 D EPTH OF F IELD BY M INIMUM B AR C ODE E LEMENT W IDTH (B ASED ON 100% UPC B AR C ODES ) Figure 30: Depth of Field Perpendicular to Flow M i n i m u m B a r C o d e E l e m e n t W i d t h A B C D E m m .13 .19 .26 .33 .48 m i l s 5.2 7.5 10.4 13 19 Specifications subject to change without notic...

30 T ROUBLESHOOTING G UIDE The following guide is for reference purposes only. Contact a Metrologicrepresentative at 1-800-ID-METRO or 1-800-436-3876 to preserve the limitedwarranty terms. MS7600 S ERIES T ROUBLESHOOTING G UIDE SYMPTOMS POSSIBLE CAUSE(S) SOLUTION All Interfaces No LEDs, beepor motor...

31 T ROUBLESHOOTING G UIDE (C ONTINUED ) SYMPTOMS POSSIBLE CAUSE(S) SOLUTION Scanning a particularsymbology that is notenabled. UPC/EAN, Code 39, interleaved2 of 5, Code 93, Code 128 andCodabar are enabled by default.Verify that the type of bar codebeing read has been selected. The unit powersup, bu...

32 T ROUBLESHOOTING G UIDE (C ONTINUED ) SYMPTOMS POSSIBLE CAUSE(S) SOLUTION The bar code mayhave been printedincorrectly. Check if it is a checkdigit/character/or borderproblem. The scanner is notconfigured correctlyfor this type of barcode. Check if check digits are setproperly. Scanner beepsat so...

34 T ROUBLESHOOTING G UIDE (C ONTINUED ) SYMPTOMS POSSIBLE CAUSE(S) SOLUTION Characters arebeing dropped. Intercharacter delayneeds to be added tothe transmitted output. Add some intercharacter delayto the transmitted output byusing the MetroSelectProgramming Guide( MLPN 00-02407). Aux port operatio...

35 D ESIGN S PECIFICATIONS MS7600 S ERIES D ESIGN S PECIFICATIONS O PERATIONAL Light Source: VLD 650 ± 10 nm Laser Power: 1.1 mW maximum Depth of Field: 0 mm to 203.2 mm (0”- 8.0”) for0.33 mm (13 mil) bar code Width of Scan Field: 87.4 mm (3.4”) @ 0 mm (0.0”);136 mm (5.35”) @ 203.2 mm (8.0”) Measure...

38 A PPLICATIONS AND P ROTOCOLS The model number on each scanner includes the scanner number and factorydefault communications protocol. S CANNER V ERSION I DENTIFIER C OMMUNICATION P ROTOCOL ( S ) 76207625 13 RS232, IBM 46xx, OCIA, Aux 76207625 37 RS232, Light Pen, Keyboard Wedge,Stand-Alone Keyboa...

44 D EFAULT S ETTINGS (C ONTINUED ) Default settings for “ Aux ” interface The secondary scanner and the MS7600 always communicate via RS232. Datais relayed to the host via various primary interfaces. P ARAMETER D EFAULT OCIA RS-232 L IGHT P EN IBM 46XX KBW USB Aux Baud Rate 38400 9 9 9 9 9 9 Aux pa...

45 S CANNER AND C ABLE T ERMINATIONS Scanner Pinout Connections The MS7600 scanner interfaces terminate to 10-pin modular jacks located on theback of the unit. The serial # label indicates the model number of the scanner. Figure 31: Scanner Interface Ports MS762x-13 OCIA MS762x-13 IBM 46xx Pin Funct...

46 S CANNER AND C ABLE T ERMINATIONS (C ONTINUED ) Figure 32: Scanner Interface Ports MS762x-37 Keyboard Wedge, Stand-Keyboard or USB MS762x-37 RS-232 or Light Pen Pin Function Pin Function 1 Ground 1 Ground 2 USB D- 2 RS-232 Transmit Output 3 USB D+ 3 RS-232 Receive Input 4 PC Data 4 RTS Output 5 P...

47 S CANNER AND C ABLE T ERMINATIONS (C ONTINUED ) Cable Connector Configurations (Host End) PowerLink Cable MLPN 54-54xxx* Pin Function 1 Shield Ground 2 RS-232 Transmit Output 3 RS-232 Receive Input 4 DTR Input 5 Power/Signal Ground 6 Reserved 7 CTS Input 8 RTS Output 9 +5VDC xxx* specifies connec...

48 S CANNER AND C ABLE T ERMINATIONS (C ONTINUED ) Cable Connector Configuration The PowerLink cable is terminated with a 5-pin DIN female connector onone end, and a 6-pin mini DIN male on the other. Metrologic will supply an adapter cable with a 5-pin DIN male connectoron one end and a 6-pin mini D...

51 N OTICES (C ONTINUED ) Attention L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peutentraîner de graves irradiations. Le client ne doit en aucun cas essayerd'entretenir lui-même le scanner ou le laser. Ne regardez jamais directement lerayon laser, même si vous croyez que ...

53 I NDEX A Accessories .................................. 2Adapter ....................................... 48Audible........................................ 22Autodiscriminates ....................... 35 B Bar Code .............................. 28, 29Beep ..................................... 22, ...