Honeywell HMLCD19- Manuals

Page 2 - ii; ISSUE DATE; SPECIFICATIONS

Rev. A ii HMMU000882 04/09/04 ISSUE DATE REVISIONS A April 2004 Initial Release (PCN 1632) Rev. A 21 HMMU000882 04/09/04 SECTION 5: SPECIFICATIONS Type TFT Color LCD Screen Size 19 ” (diagonal) Signal RGB Analog PC Input Type 15-Pin D-Sub H-Freq 31.5 ~ 80KHz Sync V-Freq 56 ~ 75Hz Display Color 16,77...

Page 3 - WARRANTY; iii; FCC COMPLIANCE STATEMENT; INFORMATION TO THE USER:; This equipment has been

Rev. A 20 HMMU000882 04/09/04 4.4 LIMITED WARRANTY Honeywell International Inc. ("Seller"), 1305 Waters Ridge Drive, Lewisville, TX 75057, warrants this monitor to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal us...

Page 4 - EXPLANATION OF GRAPHICAL SYMBOLS; CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,; C A U T I O N; RISK OF ELECTRIC SHOCK; TROUBLESHOOTING AND MAINTENANCE; No Power; AND

Rev. A iv HMMU000882 04/09/04 EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to const...

Page 5 - POWER WARNINGS; ENVIRONMENT/INSTALLATION WARNINGS

Rev. A 18 HMMU000882 04/09/04 3.4 GETTING OPTIMAL PICTURE Step 1: Window’s background or “H” character should be displayed on your screen. Step 2: Adjust the screen to the center of the Display (LCD) by using the top and bottom display controls and the V-Position Adjust menu. Step 3: Adjust the scre...

Page 6 - vi; SAFEGUARDS, CONTINUED; The following table describes the HOTKEY.; OSD KEY

Rev. A vi HMMU000882 04/09/04 SAFEGUARDS, CONTINUED ENVIRONMENT/INSTALLATION WARNINGS 2. Do not place candlelight, mosquito coils, or cigarettes on top of the monitor or install it close to heating appliances. Doing so may damage the product or create a fire danger. The product should be situated aw...

Page 7 - vii; CLEANING AND GENERAL USAGE

Rev. A 16 HMMU000882 04/09/04 3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED OSD Menu Description Horizontal position Select OSD MENU horizontal position. Vertical position Select OSD MENU vertical position. Timeout Time after which OSD MENU leaves screen. Transparency Adjust the transpare...

Page 8 - viii; PURCHASE INFORMATION; OSD Menu Description; OSD Menu

Rev. A viii HMMU000882 04/09/04 PURCHASE INFORMATION Date Purchased: Serial Number: Location Installed: Rev. A 15 HMMU000882 04/09/04 3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED OSD Menu Description The following table describes the OSD menu and a description of each option. OSD Menu De...

Page 9 - Image and sound can easily be adjusted through an OSD menu.; pq; ix; TABLE OF CONTENTS

Rev. A 14 HMMU000882 04/09/04 3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE Image and sound can easily be adjusted through an OSD menu. 4 AUTO / EXIT Used to exit OSD. 3 MENU / SEL Used to start the OSD and select options. 2 CH Z Menu move/adjust buttons. Used to move the menu bar or adjust values. ...

Page 10 - Timing Charts; Horizontal Frequency:

Rev. A x HMMU000882 04/09/04 TABLE OF CONTENTS, CONTINUED SECTION 4: TROUBLESHOOTING AND MAINTENANCE.... 19 4.1 TROUBLESHOOTING ................................................... 19 No Power ..................................................................... 19 Poor Picture Quality..................

Page 11 - PRESET MODE CHART; Input Timing Limits; INTRODUCTION

Rev. A 12 HMMU000882 04/09/04 3.2 PRESET MODE CHART Timing Charts The monitor shall be capable of supporting the following video timings: VIDEO SYNC Synch Width (T2) (T3) Back Poach (T1) Period (T4) Active (T5) Front Poach Input Timing Limits H-Sync Pulse Width 1.0 µ s ≤ Sync Pulse Width ≤ 8.0 µ s. ...

Page 12 - Some computer systems are not compatible; Do not open the monitor.; OPERATION; MANAGEMENT

Rev. A 2 HMMU000882 04/09/04 Some computer systems are not compatible with the DDC standard. If your monitor is displaying the wrong resolution, check your computer system for a DDC compatible video card and contact the Service Center. Do not open the monitor. There are no user- serviceable componen...

Page 13 - CONTENTS OF PACKAGE; OPTIONAL ACCESSORIES:

Rev. A 10 HMMU000882 04/09/04 NOTES: Rev. A 3 HMMU000882 04/09/04 1.3 CONTENTS OF PACKAGE LCD Monitor User Manual VGA Cable USER MANUAL Sound Cable AC/DC Adapter Installation Disk Power Cord Video Sound Cable Composite Cable BNC to RCA Adapters (2) OPTIONAL ACCESSORIES: S-video cable, Wall Mount ada...

Page 14 - The microcontroller has memory capacity to store 27 different; User Setting Area; The monitor automatically saves the setting value 20 seconds

Rev. A 4 HMMU000882 04/09/04 NOTES: Rev. A 9 HMMU000882 04/09/04 2.6 DISPLAY MODES MEMORY The microcontroller has memory capacity to store 27 different display modes including timing formats and display settings. This memory capacity is divided into two parts: user setting area and factory presettin...

Page 15 - FEATURES; CONTROLS AND CONNECTIONS; CONTROLS – FRONT PANEL

Rev. A 8 HMMU000882 04/09/04 2.5 MICROCONTROLLER FEATURES The microcontroller automatically detects the video board installed in your system. When the monitor is turned on, the microcontroller first checks the display mode memory stored in the user setting area and the factory presetting area. Rev. ...

Page 16 - CONTROLS – REAR PANEL; PC; INSTALLING THE MONITOR DRIVER; Pin Name

Rev. A 6 HMMU000882 04/09/04 2.2 CONTROLS – REAR PANEL PC A B C D E F G DVR or VCR A DC12V B Ear C PC Sound D VGA E Video Sound F S-VHS G Composite AV1 Rev. A 7 HMMU000882 04/09/04 2.3 INSTALLING THE MONITOR DRIVER You can achieve an optimal resolution and scanning rate by installing the monitor dri...