Honeywell 800-04433V1- Manuals

Page 3 - General Information; Package Contents; Operation; UL Compliance

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 1 – General Information The iPGSM-COM Commercial Fire Communicator includes everything you need to upgrade a commercial fire system that previously reported by POTS to a system that uses the Internet as its primary reporting pat...

Page 4 - STEP 1 – Activate the SIM and Setup the Customer Account; from your monitoring station.; Activate SIM

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 2 – STEP 1 – Activate the SIM and Setup the Customer Account The communicator requires a subscriber account (customer account) to be setup with AlarmNet Direct. This is accomplished by registering the communicator's iGSM communi...

Page 5 - plastic screw

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 3 – STEP 3 – Determine the Signal Strength and Select a Location IMPORTANT - Do Not mount this device outdoors. When choosing a suitable mounting location, understand that signal strength is very important for proper operation. ...

Page 7 - CONDUIT; BATTERY; iGSM Comm Module

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 5 – iPGSM-C0M-001-V0 TB 1 678 5 1011 9 234 1 FOR EXTERNAL ANTENNA50 OHM MMCX ONLY PRIMARY POWER: 9 - 16.5 VACCURRENT: 900mA PEAK, 70mA STANDBYBATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP FCC:XXXXXXXXXX IC: YYYYYYYYYY RSSI M0 M1 GPRS IB...

Page 8 - STEP 5 – Program the Communications Module; ] key to scroll through a list of options.; Display; Module is not yet initialized.; Failed to Update; Setting Factory Defaults

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 6 – STEP 5 – Program the Communications Module You must use the 7720P Programming tool to program the iPGSM-COM. When using the 7720P Programming tool, the values given below are for most installations. Press the [#] key to acce...

Page 9 - Close the Wall Outlet Box, then close and lock the cabinet cover.; iPGSM-COM Trouble Detection Information; Fault Condition; PowerBoost1 fault

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 7 – STEP 6 – Configure the Fire Panel 1. Ensure the Telco Fault on the panel is enabled. Then choose a setting that is no higher than 90 seconds (or as close to that) as the panel allows. 2. Ensure no more than 1 pause character...

Page 10 - Dialer Capture Module Information; LED Indicator; LED Board Information; Panel Status; used, both Telco paths must be; Buzzer

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 8 – Dialer Capture Module Information LED Indicator STATUS RED – Steady ON Messages exist in buffer. RED – Flashing No messages to be sent. Waiting for messages. GREEN – Steady ON Normal Indication. GREEN – Blinks every 2 sec. P...

Page 11 - PowerBoost1 Module Information; Missing or low battery.; You must use the DIP switch settings shown below.; PowerBoost 1

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 9 – PowerBoost1 Module Information LED Indicator STATUS AC (green) AC power available. ACTIVE (green) Cyclical flashing – normal communications. Repetition of 3 flashes – loss of communications. LOW BATT (yellow) Missing or low ...

Page 12 - iGSM Communications Module Information; GRN

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 10 – iGSM Communications Module Information TB 1 678 5 1011 9 234 1 PRIMARY POWER: 9 - 16.5 VACCURRENT: 900mA PEAK, 70mA STANDBYBATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP FCC:XXXXXXXXXX IC: YYYYYYYYYY RSSI M0 M1 GPRS IBS iPGSM-COM-00...

Page 13 - iPGSM-COM Specifications; ITEM; maximum 1A

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 11 – iPGSM-COM Specifications ITEM SPECIFICATION Cabinet Dimensions: Width = 12 3/4 inches Height = 14 7/8 inches Depth = 3 inches Transformer: (N8167) Primary – 120VAC, 60Hz, 0.50A Secondary – 18VAC, 50VA Battery: 12V, 7Ah seal...

Page 14 - NOTES

iPGSM-COM Commercial Fire Communicator – Installation and Setup Guide – 12 – NOTES

Page 15 - Wiring Diagram

Wiring Diagram The wiring diagram below is depicted for point-to-point electrical connection checks used for troubleshooting or component replacement. It is not intended to show the physical routing of wires. When replacing a wire or component, ensure the wire is routed in the same manner as the ori...

Page 16 - For the latest warranty information, please go to:

FCC STATEMENT Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environmen...