Page 2 - Disclaimer; Patents; Technical Assistance; Out of the Box; included with the order.
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this pub...
Page 3 - Front Panel
Front Panel Note: Your Dolphin model may differ from the model illustrated in this guide; however, the features noted are standard for all 7800 models unless otherwise indicated. Front Speaker General Notification LED Touch Panel Display SCAN Key Blue Modifier Key Power Key or End Call Microphone Re...
Page 5 - Installing the Battery Pack; Note: The terminal does not power ON unless the battery is locked
Installing the Battery Pack Dolphin 7800 model terminals are designed for use with standard battery pack model 7800-BTSC (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack models 7800-BTXC and 7800-BTXCW (Li-ion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc. The Dolphin 78...
Page 6 - Charging the Dolphin; ensure the internal backup battery is fully charged.; HomeBase Parts
Charging the Dolphin Dolphin terminals ship with the battery significantly discharged of power. Charge the battery with a Dolphin charging device for a minimum of 4 hours for the standard battery and 6 hours for the extended battery. Note: Charge the Dolphin terminal for at least 24 hours prior to i...
Page 7 - HomeBase LED Indicators; USB Port Communication
HomeBase LED Indicators Red The HomeBase has power but no terminal is docked. Green The HomeBase has power and the terminal is properly seated in the base. Orange The auxiliary battery is charging. Green The auxiliary battery has completed charging and is ready for use. RedFlashing The internal temp...
Page 9 - Turning the Device On/Off; Note: You should always turn the device; OFF; before removing the battery.; Suspend Mode; Removing the Battery Pack
Turning the Device On/Off Press the Power key to turn the terminal ON . Press and hold the Power key for approximately 5 seconds to turn the terminal OFF . Note: You should always turn the device OFF before removing the battery. Suspend Mode The terminal automatically enters Suspend Mode when the de...
Page 10 - Installing the SIM Card and/or Memory Card; Note: If a SIM card is installed, remove the card to reveal the memory
Installing the SIM Card and/or Memory Card 1. Turn OFF the terminal. 2. Release the hand strap and remove the battery pack. 3. Remove the screws and the protective shield covering the SIM/memory card socket. 4. Unlock the SIM card latch by sliding the latch toward the stylus slot. 5. Lift the latch ...
Page 12 - Modifier and Navigation Keys; Key Function
Modifier and Navigation Keys Key Function or The blue and red keys are used in combination with other keys to type special characters and perform system func-tions. The keyboard is color-coded to indicate the character typed or function performed when specific keys are pressed immediately after the ...
Page 13 - ENT
Function Keys Using the Color Camera 1. Tap > Demos > Camera Demo . 2. Point the camera lens at the object you want to capture. The camera lens is located on the back panel of the terminal. 3. Center the object in the touch screen display. 4. Press the ENT key or tap Snap on the touch screen. ...
Page 14 - Using the Scan Engine; SCAN; Aiming Beam; N5603 Red High-Vis Aiming Pattern
Using the Scan Engine 1. Tap > Demos > Scan Demo . 2. Point the Dolphin terminal at the bar code. 3. Press and hold the SCAN key. The aiming beam or pattern appears and the general notification LED illuminates red. 4. Center the aiming beam or pattern over the bar code. Note: For optimum perfo...
Page 15 - Resetting the Terminal
N5600 Green Aiming Beam Linear Bar Code 2D Matrix Symbol Resetting the Terminal There are three types of system resets: a soft reset, a hard reset, or a factory reset. The soft and hard resets preserve all data stored in the file system. Contact a Honeywell technical support representative for more ...
Page 16 - ActiveSync Communication; Note: Dolphin terminals ship with ActiveSync already installed.
Hard Reset (Cold Boot) A hard reset re-boots the device and closes any open applications running in RAM at the time of the reset. 1. Press and hold the BLUE + SEND keys for approximately 5 seconds. 2. The general notification LED flashes orange then green for approximately 3 seconds as the terminal ...