Honeywell 69-0786-2 - Manuals

6 69-0786—2 Program Schedule HEATING PROGRAM SCHEDULE Weekdays Start Time Heating Temperature WAKELEAVERETURNSLEEP WeekendsWAKESLEEP WAKE and RETURN start times should include extra lead time, based on outside temperatureand furnace response time, to give your furnace a head start to heat the house....

7 69-0786—2 COOLING PROGRAM SCHEDULE Weekdays Start Time Heating Temperature WAKELEAVERETURNSLEEP WeekendsWAKESLEEP WAKE and RETURN start times should include extra lead time, based on outside temperatureand furnace response time, to give your furnace a head start to heat the house. The temperatures...

8 69-0786—2 T8132C Programming Guide NOTE: Batteries are required for operation and programming. When replacing the batteries, setthe system switch to OFF. Remove the battery door (on the thermostat left side) using acoin at the bottom. Follow the instructions in Changing Batteries section. Set Curr...

10 69-0786—2 A quick guide for operating or making changes follows. NOTE: Set system switch to HEAT or COOL to perform the following: Temporarily Change temperature for current period only—press ; temperature is cancelled at next scheduled change; to cancel sooner, press . Hold a temperature indefin...

11 69-0786—2 WeekdaySchedule Usage Check Programs—press , repeatedly to see each time and temperature; then press . Cancel a program—press , until program to cancel shows; then press . Check Usage — press to determine length of time heating or air conditioning has been on since midnight; press again...

12 69-0786—2 Setting Fan and System Switches First set the fan switch. AUTO: Normal setting for most homes. A single-speed fanturns on automatically with theair conditioner or furnace. A two-speed fanusually runs on high with the air conditionerand runs on low with the furnace. ON: The fan runs cont...

13 69-0786—2 Changing Batteries IMPORTANT Batteries are required for program-ming and operation of the thermostatand heating/cooling system. As the batteries runlow, bAt Lo indicatorflashesfor oneto twomonthsbeforethe batteriesrun out com-pletely. Replace thebatteries as soon as possible after the i...

14 69-0786—2 To remove batteries, press down on the leftends of the batteries. If you insert new batter-ies within 20 to 30 seconds of removing the oldones, the thermostat does not require repro-gramming. However, if the display is blank, thebatteries are dead or incorrectly installed andthe thermos...

15 69-0786—2 Troubleshooting Guide IF… THEN… Display will not come on. ■ Set the system switch to OFF; remove batteries andinsert them backward for at least five seconds to resetthe thermostat; replace the batteries correctly. Thedisplay should come on. ■ Make sure the batteries are fresh and instal...

16 69-0786—2 Heating will not come on (Cont). ■ If display is blank or displays bAt Lo, install fresh batteries. ■ If temperature setting is higher than current temperature,and thermostat displays HEAT, contact HoneywellCustomer Assistance at 1-800-468-1502. Cooling will not come on. ■ Check that th...

19 69-0786—2 Limited One-Year Warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the pr...

20 69-0786—2 69-0786—2 Rev. 5-96 J.S. Printed in MexicoCopyright © 1996 Honeywell Inc. All Rights Reserved Home and Building Control Honeywell Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Helping You Control Your World Home and Building Control Honeywell Limited-Honeywell Limitée 155 Gordon...