Honeywell 408EU - Manuals

– 7 – System Reference ZONE DESCRIPTION 1 2 3 4 5 6 7 8 ENTRY TIME 1 DOOR EXIT TIME* ENTRY TIME 2 DOOR * Exit time is the same for all designated entry/exit doors. The following SEND HELP ALERTS can be programmed into your system. Both keys must be pressed at the same time to activate the alert. The...

– 10 – System Operation You can arm or disarm the burglar portion of your security system. Before you can arm the system, it must be “ready.” If you have a protected door open, or if someone is moving in view of a motion detector, the system will not display “ READY .” The system is ready if the REA...

– 13 – System Operation (cont’d) To Arm the System In Instant Mode In INSTANT mode, all alarm sensors, including doors that normally have a delay to allow you to disarm the system, will immediately report an alarm if activated. Check to make sure the system is ready. When it is ready, press: INSTANT...

– 15 – System Operation (cont’d) If no alarms have taken place, the ARMED LED goes off, and the display shows: LCD Keypad: SYSTEM READY Fixed-Word Keypad: READY LED lit If alarms occurred while the system was armed, or if a trouble condition exists, the display shows: LCD Keypad: ALM MEM ZN1 FRONT D...

– 16 – User Codes Adding/Changing a User Code Users can be added or changed directly at the keypad. Your system can have up to 6 different User Codes. To add or change a User Code, press the following: Master User Code User ID (1-6) New User Code CODE NOTES: • User number 1 is a master user and can ...

– 17 – Paging Feature Your installer may have programmed your system to send messages with certain system conditions to your pager. An explanation of those messages is provided below. Follow-Me Displays The display shown on your pager is "ACCTEXXX" where: "ACCT" is the 4-digit centra...

– 18 – Paging Feature (cont’d) 1. Access pager number programming by pressing in sequence the [#], [5], and [8] keys. An acknowledgement tone sounds to indicate pager number programming has been accessed. The [#], [5], [8] command is accessible only while the system is disarmed and the dialer, diale...

– 19 – Miscellaneous Commands Arm System (Maid Code) If you choose to have a code that cannot disarm the system, but can arm the system, have your installer program this feature. If programmed, User Code No. 5 has system arming capability only, and you can issue this code to a temporary user so they...

– 20 – Miscellaneous Commands (cont’d) Quick Forced Arm Yes No If programmed by your installer, Quick Forced Arm allows you to arm the burglar portion of your alarm system in the Away mode, bypassing all zones that are not ready. To enable Quick Force Arm: Press [#], [2]. A valid User Code is still ...

– 21 – Miscellaneous Commands (cont’d) The display will show: LCD Keypad: BYPASSED: ZN1 Fixed-Word Keypad: 01 BYPASS Set Time and Date To set the time and date, press [#], [3]. Enter 2 digits each for hours, minutes, month, day, and year. hours (00-23) minutes (01-59) month (01-12) day (01-31) year ...

– 22 – Testing the System System Test We recommend that you test your system once a week using the following procedure: If your system is monitored, contact your central station before you perform this test. 1. Arm your security system. 2. Wait until your exit time is over and then activate the syst...

– 23 – Recommendations on Smoke Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association’s (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of...

– 24 – Emergency Evacuation 2nd FLOOR BACK FRONT floor_plan2-V0 BA TH CLOSET BEDR OOM BEDR OOM BEDR OOM 1st FLOOR BA TH KITCHEN BEDR OOM BEDR OOM PORCH BACK DOOR Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protectio...

– 25 – RADIO FREQUENCY EMISSIONS STATEMENTS FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference r...

– 26 – INDUSTRIE CANADA AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences t...

– 27 – System Limitations While this system is an advanced-design security system, it does not offer guaranteed protection against burglary, fire, or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For exampl...

– 29 – Glossary AC/LB LED : Yellow LED that, when lit, indicates the system is running on electricity; when not lit, indicates the system is running on the backup battery. ALARM : Sound from keypad or other horn/siren indicates a burglar alarm, fire alarm, or other condition you should be alerted to...

– 31 – Glossary (cont’d) SENSOR : The actual alarm sensor, detector, or device installed to detect an intrusion, fire, or environmental problem. Examples include: door contacts, window contacts, motion sensors, glassbreak sensors, smoke detectors, rate-of-rise heat detectors, temperature sensors, fl...

ONE YEAR LIMITED WARRANTY Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials and workmanship for one year...