Page 2 - Disclaimer
Disclaimer Honeywell International Inc. (“Honeywell”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Honeywell to determine whether any such changes have been made. The information...
Page 3 - Table of Contents
i Chapter 1 - Getting Started About This Manual .......................................................1-1Unpacking the Imager ..................................................1-13800g Models ..............................................................1-1Connecting the Imager with USB ..............
Page 4 - ii; Chapter 4 - Data Editing
ii Good Read Indicators .................................................. 3-1 Beeper – Good Read ............................................. 3-1Beeper Volume – Good Read................................ 3-1Beeper Pitch – Good Read .................................... 3-1Beeper Duration – Good Read...
Page 5 - iii; Chapter 5 - Data Formatting
iii Intercharacter, Interfunction, and IntermessageDelays ..........................................................................4-4 Intercharacter Delay ...............................................4-5User Specified Intercharacter Delay ......................4-5Interfunction Delay ...............
Page 6 - iv
iv Code 39 ....................................................................... 7-5 Code 39 Start / Stop Characters ............................. 7-5Code 39 Check Character ..................................... 7-5Code 39 Message Length...................................... 7-6Code 39 Append .......
Page 8 - vi; Chapter 8 - Interface Keys
vi China Post Code........................................................ 7-28Korea Post Code ....................................................... 7-29 Korea Post Message Length ............................... 7-29 PosiCode ................................................................... 7-29...
Page 9 - vii; Chapter 11 - Serial Programming Commands
vii Chapter 11 - Serial Programming Commands Conventions ...............................................................11-1Menu Command Syntax ............................................11-1 Query Commands ................................................11-2Concatenation of Multiple Commands ........
Page 10 - viii
Page 11 - FCC Part 15 Subpart B Class B; UL Statement
Product Agency Compliance USA FCC Part 15 Subpart B Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that m...
Page 12 - Canada; Industry Canada ICES-003; Conformité à la règlementation canadienne; cUL Statement; Europe; Waste Electrical and Electronic Equipment
Canada Industry Canada ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired o...
Page 14 - International; CB Scheme; Patents
International Eye Safety Statement (LED) This device has been tested in accordance with IEC60825-1:1993 +A:1997 +A2:2001 LED safety, and has been certified to be under the limits of a Class 1 LED device. Caution: Use of controls or adjustments or performance of procedures other than those specified ...
Page 15 - 800g Imager Identification; Light Source
3800g Imager Identification Light Source Item Number, Serial Number and Revision Compliance Label location
Page 17 - Getting Started; About This Manual
3800g/3800gHD/3800gPDF User’s Guide 1 - 1 1 Getting Started About This Manual This User’s Guide provides installation and programming instructions for the 3800g. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell bar code imagers are factory p...
Page 18 - Connecting the Imager with USB; USB PC or Macintosh Keyboard
1 - 2 3800g/3800gHD/3800gPDF User’s Guide Connecting the Imager with USB Note: Honeywell recommends connecting the imager end of the cable first and the host end second. An imager can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the imager and to the comp...
Page 20 - Plug and Play
1 - 4 3800g/3800gHD/3800gPDF User’s Guide ACK/NAK Mode Plug and Play Plug and Play bar codes provide instant imager set up for commonly used inter-faces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Connecting the Imager When Powered by Host (...
Page 21 - Keyboard Wedge Connection
3800g/3800gHD/3800gPDF User’s Guide 1 - 5 3. Connect the appropriate interface cable to the imager and to the terminal/ computer. 4. Turn the terminal/computer power back on. Note: You will not hear a power-up beep because the 3800g is factory defaulted to a USB connection. You must scan the IBM PC ...
Page 22 - Connecting the Imager with RS-232 Serial Port
1 - 6 3800g/3800gHD/3800gPDF User’s Guide Laptop Direct Connect For most laptops, scanning the Laptop Direct Connect bar code allows opera- tion of the imager in parallel with the integral keyboard. The following Laptop Direct Connect bar code selects terminal ID 03, programs a carriage return (CR) ...
Page 24 - Reading Techniques; Reading PDF417 Bar Codes
1 - 8 3800g/3800gHD/3800gPDF User’s Guide Reading Techniques The imager has a bright red aiming beam that corresponds to its horizontal field of view. The aiming beam should be centered horizontally over the bar code; it will not read if the aiming beam is in any other direction. The best focus poin...
Page 25 - Resetting the Standard Product Defaults; dard Product Default Settings
3800g/3800gHD/3800gPDF User’s Guide 1 - 9 Resetting the Standard Product Defaults If you aren’t sure what programming options are in your imager, or you’ve changed some options and want the factory settings restored, scan the Stan- dard Product Default Settings bar code below. The Menu Commands star...
Page 27 - Terminal Interfaces
3800g/3800gHD/3800gPDF User’s Guide 2 - 1 2 Terminal Interfaces Terminal ID If your interface is not a standard PC AT, refer to Terminal ID , beginning on page 2-1 and locate the Terminal ID number for your PC. Scan the Terminal ID bar code below, then scan the numeric bar code(s) from the Programmi...
Page 28 - Supported Terminals
2 - 2 3800g/3800gHD/3800gPDF User’s Guide Supported Terminals Terminal Model(s) Terminal ID DEC VT510, 520, 525 (PC style) 005 DEC VT510, 520, 525 (DEC style LK411) 104 Esprit 200, 400 005 Heath Zenith PC, AT 003 HP Vectra 003 IBM XT 001 IBM PS/2 25, 30, 77DX2 002 IBM AT, PS/2 30–286, 50, 55SX, 60, ...
Page 30 - Keyboard Country
2 - 4 3800g/3800gHD/3800gPDF User’s Guide Keyboard Country Scan the appropriate country code below to program the keyboard for your country. As a general rule, the following characters are supported, but need special care for countries other than the United States:@ | $ # { } [ ] = / ‘ \ < > ~...
Page 31 - Keyboard Style; Regular
3800g/3800gHD/3800gPDF User’s Guide 2 - 5 Please refer to Honeywell website ( www.honeywell.com/aidc ) for complete key- board country support information and applicable interfaces. If you need to pro-gram a keyboard for a country other than one listed above, scan the Program Keyboard Country bar co...
Page 32 - Emulate External Keyboard; Keyboard Modifiers
2 - 6 3800g/3800gHD/3800gPDF User’s Guide Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer. Keyboard Modifiers This modifies special keyboard fea...
Page 33 - Automatic Direct Connect Mode:
3800g/3800gHD/3800gPDF User’s Guide 2 - 7 Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off Numeric Keypa...
Page 35 - Parity
3800g/3800gHD/3800gPDF User’s Guide 2 - 9 Parity provides a means of checking character bit patterns for validity. Default = None. 7 Data, 1 Stop, Parity Even 7 Data, 1 Stop, Parity None 7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop Parity None * 8 ...
Page 37 - Output; Good Read Indicators; Beeper – Good Read; Beeper Pitch – Good Read
3800g/3800gHD/3800gPDF User’s Guide 3 - 1 3 Output Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = O...
Page 39 - Good Read Delay; User-Specified Good Read Delay; Trigger Modes; Manual/Serial Trigger
3800g/3800gHD/3800gPDF User’s Guide 3 - 3 Good Read Delay This sets the minimum amount of time before the imager can read another bar code. Default = No Delay. User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from...
Page 40 - Automatic Trigger
3 - 4 3800g/3800gHD/3800gPDF User’s Guide ger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by scanning digits from the inside back cover, then scanning Save . Default = 30,000. Automatic Trigger The imager scans continuously using intern...
Page 41 - Reread Delay; Centering Window
3800g/3800gHD/3800gPDF User’s Guide 3 - 5 Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back cover, and Save . Default = 5,000 ms. Reread Delay This sets the time period before the imager can read the same bar code a sec- ond tim...
Page 44 - Output Sequence Overview; Default Sequence; F F
3 - 8 3800g/3800gHD/3800gPDF User’s Guide Output Sequence Overview Require Output Sequence When turned off, the bar code data will be output to the host as the imager decodes it. When turned on, all output data must conform to an edited sequence or the imager will not transmit the output data to the...
Page 45 - Discard; Output Sequence Editor; Required
3800g/3800gHD/3800gPDF User’s Guide 3 - 9 • Discard This exits without saving any Output Sequence changes. Output Sequence Editor Require Output Sequence When an output sequence is Required , all output data must conform to an edited sequence or the imager will not transmit the output data to the ho...
Page 46 - Output Sequence Example
3 - 10 3800g/3800gHD/3800gPDF User’s Guide Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 barcodes, but you want the image scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example. You wo...
Page 48 - Multiple Symbols; No Read
3 - 12 3800g/3800gHD/3800gPDF User’s Guide When the output sequence is Off , the barcode data is output to the host as the image scanner decodes it. Note: This selection is unavailable when the Multiple Symbols Selection is turned on. Multiple Symbols When this programming selection is turned On , i...
Page 49 - Video Reverse
3800g/3800gHD/3800gPDF User’s Guide 3 - 13 Video Reverse Video Reverse is used to allow the imager to read bar codes that are inverted. The “Off ” bar code below is an example of this type of bar code. Note: If additional menuing is required, Video Reverse must be disabled to read the menu bar codes...
Page 51 - Data Editing; Prefix/Suffix Overview; Points to Keep In Mind; To Add a Prefix or Suffix:
3800g/3800gHD/3800gPDF User’s Guide 4 - 1 4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in ...
Page 53 - To Add a Carriage Return Suffix to All Symbologies
3800g/3800gHD/3800gPDF User’s Guide 4 - 3 Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9 , 9 for all symbologies. Your change is automatically saved. To Add a Carriage Return Suffix to All Symbologies Scan the following bar code if you wi...
Page 55 - Intercharacter Delay; User Specified Intercharacter Delay
3800g/3800gHD/3800gPDF User’s Guide 4 - 5 Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of milliseconds and the SAVE bar code using th...
Page 56 - Interfunction Delay; Intermessage Delay
4 - 6 3800g/3800gHD/3800gPDF User’s Guide Interfunction Delay An interfunction delay of up to 495 milliseconds may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the number of milliseconds and the SAVE bar code using t...
Page 57 - Data Formatting; Data Format Editor Introduction; To Add a Data Format
3800g/3800gHD/3800gPDF User’s Guide 5 - 1 5 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the imager’s output. For exam-ple, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in t...
Page 58 - Other Programming Selections; Data Format Editor Commands
5 - 2 3800g/3800gHD/3800gPDF User’s Guide inside back cover to program the imager for your terminal ID (you must enter 3 digits). For example, scan 0 0 3 for an AT wedge. Note: The wildcard for all terminal types is 099. Step 4. Code I.D. In Appendix A find the symbology to which you want to apply t...
Page 59 - Move Commands; Miscellaneous Commands
3800g/3800gHD/3800gPDF User’s Guide 5 - 3 (00-99) for the number of characters and xx stands for the hex value for an ASCII code. See ASCII Conversion Chart (Code Page 1252) on page A-2.) F3 Send up to but not including “ss” character (Search and Send) starting from current cursor position, leaving ...
Page 60 - xx; Data Format Editor
5 - 4 3800g/3800gHD/3800gPDF User’s Guide and xxyy .. zz is the list of characters to be suppressed. (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-2.) FC Disables suppress filter and clear all suppressed characters. Syntax = FC . E4 Replaces up...
Page 63 - Secondary Interface; Enabling the Secondary Interface; Secondary RS-232 Connection
3800g/3800gHD/3800gPDF User’s Guide 6 - 1 6 Secondary Interface By switching secondary interface cables, the 3800g imager, for example, can communicate with a portable data terminal (secondary interface) in addition to the host terminal (primary interface). See the table below for the secondary inte...
Page 64 - Secondary Trigger Mode
6 - 2 3800g/3800gHD/3800gPDF User’s Guide RS-232 programmable selections are used by both the primary and secondary interfaces. Changing an RS-232 parameter (e.g., baud rate or parity), while in primary or secondary mode will affect both interfaces. If you want to change the RS-232 settings, refer t...
Page 67 - Symbologies; Introduction
3800g/3800gHD/3800gPDF User’s Guide 7 - 1 7 Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 11 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • China Post Code • Korea Post Code • Codabar • Matrix 2 of 5 • Codablock F • Mi...
Page 68 - All Symbologies; All Symbologies On; Message Length
7 - 2 3800g/3800gHD/3800gPDF User’s Guide All Symbologies If you want to decode all the symbologies allowable for your imager, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particula...
Page 69 - Codabar; Codabar Check Character; No Check Character
3800g/3800gHD/3800gPDF User’s Guide 7 - 3 Codabar <Default All Codabar Settings> Codabar Codabar Start / Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit . Coda...
Page 70 - Codabar Concatenation
7 - 4 3800g/3800gHD/3800gPDF User’s Guide When Check Character is set to Validate, but Don’t Transmit , the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. Codabar Concatenation Codabar supports symbol concatenati...
Page 71 - Codabar Message Length; Code 39 Start / Stop Characters; Code 39 Check Character
3800g/3800gHD/3800gPDF User’s Guide 7 - 5 Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Code 39 < Default All Code 39 Sett...
Page 72 - Code 39 Message Length; Code 39 Append
7 - 6 3800g/3800gHD/3800gPDF User’s Guide When Check Character is set to Validate and Transmit , the imager only reads Code 39 bar codes printed with a check character, and will transmit this charac-ter at the end of the scanned data. Default = No Check Character. Code 39 Message Length Scan the bar...
Page 73 - Full ASCII
3800g/3800gHD/3800gPDF User’s Guide 7 - 7 Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF. Note: Trioptic Code must be turned off to scan Code 32 Pharmaceutical codes. Full ASCII If Full ASCII ...
Page 74 - Code 39 Code Page; < Default All Interleaved 2 of 5 Settings >; Interleaved 2 of 5
7 - 8 3800g/3800gHD/3800gPDF User’s Guide Character pairs /M and /N decode as a minus sign and period respectively.Character pairs /P through /Y decode as 0 through 9. Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the pro...
Page 75 - Interleaved 2 of 5 Message Length
3800g/3800gHD/3800gPDF User’s Guide 7 - 9 When Check Digit is set to Validate and Transmit , the imager only reads Inter- leaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. Interleaved 2 of 5 Message Length Scan ...
Page 76 - Code 93 Message Length; Code 93 Code Page
7 - 10 3800g/3800gHD/3800gPDF User’s Guide Code 93 < Default All Code 93 Settings > Code 93 Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Max...
Page 77 - Straight 2 of 5 IATA
3800g/3800gHD/3800gPDF User’s Guide 7 - 11 Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Settings> Straight 2 of 5 Industrial Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 fo...
Page 78 - Straight 2 of 5 IATA Message Length; Matrix 2 of 5 Message Length
7 - 12 3800g/3800gHD/3800gPDF User’s Guide Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Matrix 2 of 5 <Defau...
Page 79 - Check Digits Required
3800g/3800gHD/3800gPDF User’s Guide 7 - 13 Code 11 <Default All Code 11 Settings> Code 11 Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. On * Off One Check Digit * Two Check Digits
Page 80 - Code 11 Message Length; ISBT 128 Concatenation
7 - 14 3800g/3800gHD/3800gPDF User’s Guide Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Code 128 <Default All Code 128 Se...
Page 81 - Code 128 Message Length; Code 128 Function Code Transmit; Telepen
3800g/3800gHD/3800gPDF User’s Guide 7 - 15 Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Code 128 Code Page Code pages defin...
Page 83 - UPC A
3800g/3800gHD/3800gPDF User’s Guide 7 - 17 UPC A <Default All UPC A Settings> UPC A UPC A Check Digit This selection allows you to specify whether the check digit should be transmit-ted at the end of the scanned data or not. Default = On. UPC A Number System The numeric system digit of a U.P.C...
Page 84 - UPC A Addenda; UPC A Addenda Required
7 - 18 3800g/3800gHD/3800gPDF User’s Guide UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data. Default = Off for both 2 Digit and 5 Digit Addenda. UPC A Addenda Required When Addenda Required is set to on, the imager will only read UPC A bar codes that have addenda....
Page 85 - UPC E; UPC E0 and UPC E1
3800g/3800gHD/3800gPDF User’s Guide 7 - 19 UPC-A/EAN-13with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. Default = On. UPC E <Default All UPC E Settings> UPC E0 and UPC E1 Most U.P.C. bar codes lead with the 0 number system. For ...
Page 86 - UPC E0 and UPC E1 Expand; UPC E0 and UPC E1 Addenda Required
7 - 20 3800g/3800gHD/3800gPDF User’s Guide UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off. UPC E0 and UPC E1 Addenda Required When Addenda Required is set to on, the imager will only read UPC E bar codes that have addenda. Default = Not Requ...
Page 88 - EAN/JAN 13 Check Digit; EAN/JAN 13 Addenda Required
7 - 22 3800g/3800gHD/3800gPDF User’s Guide EAN/JAN 13 EAN/JAN 13 Check Digit This selection allows you to specify whether the check digit should be transmit-ted at the end of the scanned data or not. Default = On. EAN/JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN...
Page 89 - EAN/JAN 13 Addenda Separator; ISBN Translate
3800g/3800gHD/3800gPDF User’s Guide 7 - 23 EAN/JAN 13 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. Note: If you want to enable or disable EAN13 with Extended Coupon Code...
Page 90 - EAN/JAN 8 Check Digit; EAN/JAN 8 Addenda Required
7 - 24 3800g/3800gHD/3800gPDF User’s Guide EAN/JAN 8 EAN/JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmit-ted at the end of the scanned data or not. Default = On. EAN/JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 ...
Page 91 - EAN/JAN 8 Addenda Separator; MSI
3800g/3800gHD/3800gPDF User’s Guide 7 - 25 EAN/JAN 8 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. MSI <Default All MSI Settings> MSI MSI Check Character Different ...
Page 92 - MSI Message Length; Plessey Code; GS1 DataBar Omnidirectional; < Default All GS1 DataBar Omnidirectional Settings >
7 - 26 3800g/3800gHD/3800gPDF User’s Guide MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Plessey Code <Default All Plessey Cod...
Page 93 - < Default All GS1 DataBar Limited Settings >; GS1 DataBar Limited; GS1 DataBar Expanded; < Default All GS1 DataBar Expanded Settings >
3800g/3800gHD/3800gPDF User’s Guide 7 - 27 GS1 DataBar Omnidirectional GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > * On Off * On Off
Page 94 - China Post Code
7 - 28 3800g/3800gHD/3800gPDF User’s Guide GS1 DataBar Expanded GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. Ch...
Page 95 - Korea Post Code; PosiCode
3800g/3800gHD/3800gPDF User’s Guide 7 - 29 Korea Post Code <Default All Korea Post Code Settings> Korea Post Code Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 2-80....
Page 96 - Trioptic Code
7 - 30 3800g/3800gHD/3800gPDF User’s Guide PosiCode A and B You have to have PosiCode A and B on to read any of the PosiCode symbolo-gies. PosiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximu...
Page 97 - Codablock F
3800g/3800gHD/3800gPDF User’s Guide 7 - 31 Codablock F <Default All Codablock F Settings> Codablock F Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-2048. Minimum ...
Page 98 - Code 16K Message Length
7 - 32 3800g/3800gHD/3800gPDF User’s Guide Code 16K Code 16K Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 0-160. Minimum Default = 1, Maximum Default = 160. Code 49 <Default All ...
Page 99 - Code 49 Message Length; PDF417 Message Length
3800g/3800gHD/3800gPDF User’s Guide 7 - 33 Code 49 Code 49 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81. PDF417 (3800gHD/3800gPDF onl...
Page 100 - MicroPDF417 Message Length; GS1 Composite Codes
7 - 34 3800g/3800gHD/3800gPDF User’s Guide MicroPDF417 (3800gHD/3800gPDF only) < Default All MicroPDF417 Settings > MicroPDF417 MicroPDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length (page 7-2) for additional information. Minimum and Maximum le...
Page 101 - GS1 Composite Code Message Length; GS1 Emulation
3800g/3800gHD/3800gPDF User’s Guide 7 - 35 UPC/EAN Version Scan the UPC/EAN Version On barcode to decode GS1 Composite symbols that have a UPC or EAN linear component. (This does not affect GS1 Compos-ite symbols with a GS1-128 or GS1linear component. If either of these codes are the linear componen...
Page 103 - Interface Keys
3800g/3800gHD/3800gPDF User’s Guide 8 - 1 8 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the imager. Refer to page 2-6 enable Control + ASCII mode. Function Code...
Page 109 - Utilities; To Add a Test Code I.D. Prefix to All Symbologies; Standard Product Default Settings
3800g/3800gHD/3800gPDF User’s Guide 9 - 1 9 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, included in the "Appendix A" on page A-1 ) for the single character...
Page 110 - Temporary Visual Xpress Configuration
9 - 2 3800g/3800gHD/3800gPDF User’s Guide Temporary Visual Xpress Configuration For quick download communication configuration, scan the Visual Xpress bar code to temporarily configure the imager for Visual Xpress settings. Refer to Visual Xpress on page 10-1 for additional information about Visual ...
Page 111 - Visual Xpress Introduction; Visual Xpress Operations; Scan Data
3800g/3800gHD/3800gPDF User’s Guide 10 - 1 10 Visual Xpress Visual Xpress Introduction Visual Xpress provides a wide range of PC-based programming functions that can be performed on an imager connected to your PC's COM port. Visual Xpress allows you to download upgrades to the imager's firmware, cha...
Page 112 - Installing Visual Xpress from the Web
10 - 2 3800g/3800gHD/3800gPDF User’s Guide Installing Visual Xpress from the Web 1. Access the Honeywell web site at www.honeywell.com/aidc . 2. Click in the Quick Search text box and enter Visual Xpress . 3. Click on Search Now . 4. Click on the entry for Visual Xpress . 5. When prompted, select Sa...
Page 113 - Serial Programming Commands; Conventions; Menu Command Syntax
3800g/3800gHD/3800gPDF User’s Guide 11 - 1 11 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro-gram the 3800g. For complete descriptions and examples of each serial pro-gramm...
Page 114 - Query Commands; Concatenation of Multiple Commands
11 - 2 3800g/3800gHD/3800gPDF User’s Guide Query Commands Several special characters can be used to query the device about its settings. ^ What is the default value for the setting(s). ? What is the device’s current value for the setting(s). * What is the range of possible values for the setting(s)....
Page 115 - Examples of Query Commands
3800g/3800gHD/3800gPDF User’s Guide 11 - 3 Examples of Query Commands In the following examples, a bracketed notation [ ] depicts a non-displayable response. Example: Example #1:What is the range of possible values for Codabar Coding Enable? Enter: cbrena*. Response: CBRENA0-1[ACK] This response ind...
Page 119 - Output Selections
3800g/3800gHD/3800gPDF User’s Guide 11 - 7 Word Length: Data Bits, Stop Bits, and Parity 7 Data, 1 Stop, Parity Even 232WRD3 2-9 7 Data, 1 Stop, Parity None 232WRD0 2-9 7 Data, 1 Stop, Parity Odd 232WRD6 2-9 7 Data, 2 Stop, Parity Even 232WRD4 2-9 7 Data, 2 Stop, Parity None 232WRD1 2-9 7 Data, 2 St...
Page 121 - Prefix/Suffix Selections
3800g/3800gHD/3800gPDF User’s Guide 11 - 9 Reread Delay Short (500 ms) DLYRRD500 3-5 *Medium (750 ms) DLYRRD750 3-5 Long (1000 ms) DLYRRD1000 3-5 Extra Long (2000 ms) DLYRRD3000 3-5 User-Specified Reread Delay Range 0 - 30,000 ms DLYRRD##### 3-5 Centering Centering On DECWIN1 3-6 *Centering Off DECW...
Page 133 - Product Specifications; 800g Product Specifications; Parameter
3800g/3800gHD/3800gPDF User’s Guide 12 - 1 12 Product Specifications 3800g Product Specifications Parameter Specification Dimensions (Typical): Height 5.9 inches (15 cm) Length 4.4 inches (11.2 cm) Width 3.1 inches (7.9 cm) Weight 5.6 ounces (160 g) Light Source 630 nm visible red LED @ 800µW max ra...
Page 135 - Standard Cable Pinouts; Keyboard Wedge
3800g/3800gHD/3800gPDF User’s Guide 12 - 3 Standard Cable Pinouts Keyboard Wedge 10 Pin RJ41 Modular Plug connects to the imager handle 1 2 C ord shield 3 T ied to supply power 4 S upply ground 5 T erminal clock 6 T erminal data 7 S upply power input (Refer to tables on page 12-1 ) 8 K eyboard data ...
Page 136 - Serial Output
12 - 4 3800g/3800gHD/3800gPDF User’s Guide Standard Cable Pinouts Serial Output 10 Pin RJ41 Modular Plug connects to the imager handle 1 2 C ord shield 3 P rog 1 (Tied to supply power for primary cable) 4 S upply ground 5 R eceive data - Serial data to imager 6 T ransmit data - Serial data from imag...
Page 137 - USB
3800g/3800gHD/3800gPDF User’s Guide 12 - 5 Standard Cable Pinouts USB 10 Pin Modular Plug connects to the imager handle 1 2 D ata + 3 T ied to supply power 4 S upply ground 5 6 7 5 volt supply power input 8 9 10 Data -
Page 139 - Repairs; Maintenance; Cleaning the Device; Inspecting Cords and Connectors; Do not submerge the imager in water. Do not use
3800g/3800gHD/3800gPDF User’s Guide 13 - 1 13 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These ser-vices are to be performed only by an authorized service center. Please see Customer Support on page 14-1 for further information. Maintenance The 3800g provide...
Page 140 - Troubleshooting
13 - 2 3800g/3800gHD/3800gPDF User’s Guide Replacing the Interface Cable The standard interface cable is attached to the scanner with an 10-pin modular connector. When properly seated, the connector is held in the 3800g scanner’s handle by a flexible retention tab. The interface cable is designed to...
Page 143 - Technical Assistance; Online Technical Assistance
3800g/3800gHD/3800gPDF User’s Guide 14 - 1 14 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please call your distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263Fax number: (315) 554-6705 E-mail:...
Page 144 - Product Service and Repair; Online Product Service and Repair Assistance
14 - 2 3800g/3800gHD/3800gPDF User’s Guide Product Service and Repair Honeywell provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA...
Page 145 - Limited Warranty
3800g/3800gHD/3800gPDF User’s Guide 14 - 3 Limited Warranty Honeywell International Inc. ("Honeywell") warrants its products to be free from defects in materials and workmanship and to conform to Honeywell’s published specifications applicable to the products purchased at the time of shipmen...
Page 147 - Symbology Chart
3800g/3800gHD/3800gPDF User’s Guide A - 1 A Appendix A Symbology Chart Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details. Note: Prefix / Suffix entries for specific symbologies override the unive...
Page 148 - ASCII Conversion Chart (Code Page 1252
A - 2 3800g/3800gHD/3800gPDF User’s Guide ASCII Conversion Chart (Code Page 1252 ) Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings. Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char 0 00 NUL 32 20 64 40 @ 96 60 ‘ 1...
Page 151 - Sample Symbols
3800g/3800gHD/3800gPDF User’s Guide Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 Code 128 EAN 13 1234567890 Code 128 9 780330 290951 654 EAN 8 3210 5 456123 8 0 UPC-E
Page 152 - Straight 2 of 5 Industrial
3800g/3800gHD/3800gPDF User’s Guide Sample Symbols Code 93 123456-9$ Straight 2 of 5 Industrial 123456 Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012 Code 39 Codabar BC321 A13579B Micro PDF417 Test Message PDF417 Car Registration
Page 156 - Honeywell
Honeywell 700 Visions DriveP.O. Box 208Skaneateles Falls, NY 13153-0208 3800g-UG Rev B 6/08
Honeywell DT8050A
Installation Manual
Honeywell DT8050
Manual
Honeywell TPFIT25WK
User Manual
Honeywell TPFIT32AWK
User Manual
Honeywell 24DX47
User Manual
Honeywell TPFIT50PWK
User Manual
Honeywell TPFIT50WK
User Manual
Honeywell 00010
User Manual
Honeywell ADVBLEWIFI
Manual