Honeywell 16 Plus - Manuals

vii QUICK OPERATION GUIDE A SET (an Unset system) B PART SET (Defaults to Parts 1 and 2) 1 key • toggles the Set (ON)/Unset (OFF) status of Part 1 2 key • toggles the Set (ON)/Unset (OFF) status of Part 2 3 key • toggles the Set (ON)/Unset (OFF) status of Part 3 e n t UNSET (a Set system) 1 OMIT ZON...

ix GLOSSARY OF TERMS Chime: Zone attribute which gives an audible indication of the activation of a detector or contact. Duress: Applicable when a remote signalling device is fitted. A Duress code entered at the keypad will unset the system but transmit a Duress code to the Alarm Receiving Centre. E...

1 KEYPAD INFORMATION The Galaxy system is programmed and operated from the LCD keypads. GALAXY 16+ V2.708:58 TUE 22 NOV 1 2 3 A 4 5 6 B 7 8 9 ent * 0 # esc 2 x 16 CHARACTERLCD DISPLAY POWER LED Number Keys ( 0–9 ): are used to enter your User Code and to select and modify options. View ( A and B ) K...

3 Your alarm system can be Part Set using the B key. To Part Set the system enter your User Code then press the B key. The keypad then displays the Set/Unset status of those parts assigned to your code, see Figure 2 Part Setting Options. Figure 2: Part Setting Options. SETTING AND UNSETTING THE SYST...

4 The Parts marked ‘ON’ are Set, those marked ‘OFF’ are Unset. To alter the set/unset status of aPart press the number corresponding to that part, that is, pressing the 1 key toggles the setstatus of Part 1 between set/unset. The equals sign denotes that what is displayed beside the Part number is t...

5 Alarm Abort Note: If the system is programmed for Alarm Abort a period of 90 seconds after expiry of theEntry Time is provided to enable the user to cancel an alarm caused by exceeding theEntry Time or deviating from the entry route.If the 90 second Alarm Abort time is exceeded then a full alarm m...

7 USER MENU For access to the menu options enter your user code then press the ent key. The keypad then displays the menu options available to the user. Table 2: Menu Options. The user menu offers a selection of up to seven options. All users have access to the Chimeand Walk options. The Omit and Co...

8 Omitting Zones When the Omit option is selected, zone 01 is displayed, along with it’s omit eligibility andstatus (NON OMITTABLE – the zone cannot be omitted; #,xx OMIT – the zone is omittable(where xx is the zone number); OMIT – the zone is currently omitted). If the zone is currently omitted the...

9 On selecting the Walk option zone 01 is displayed. If the zone is to be tested press the # key. Use the A or B keys to scroll through the zones on the system, each one may be selected for inclusion in the test. When all the required zones have been selected press the ent key to startthe Walk Test....

10 Note: User Code 13 may be assigned as a Duress Code. Entry of this code causes a Duressalarm which will activate the PA outputs and trigger the Remote signalling Device (iffitted); the Horn, Bells and Strobe outputs do not activate. The installation engineer will advise you on the operation of th...

11 Figure 4: Viewing the Event Log. The log event displays the event type, time, descriptor and number. Also displayed is theactivation (+) and deactivation (–) signaller. To display the date of the event currently being displayed press the # key. Pressing the # key again returns the display to the ...

12 To quickly move through the log enter a three digit number between 001 and 250 followed bythe # key. The system will jump to the event number entered. To exit from the Log option press the esc key. Option 10 – Time The Time option allows the system manager (User 14) to modify the four time featur...

13 APPENDIX A — ALARM AND HELP MESSAGES ALARM IS ACTIVE: The system is currently in alarm and must be cancelled by a valid user code. PA RESET REQUIRED : The user code that cancelled the PA alarm does not have the authori- sation to reset the system. A user code with the PA Reset attribute enabled m...

15 APPENDIX B — AVOIDING FALSE ALARMS False alarms are inconvenient and may give rise to Police response being withdrawn from yoursite which may affect your insurance cover. Here are twelve points to help you avoid false alarms: 1. Ensure that you understand how to operate the alarm system. In your ...

17 APPENDIX C — CONFORMITY AND STANDARDS Compliance The Galaxy 16 and 16 plus is compatible with the relevant parts of the following standards: • BS 4737 • EN 60950 • CTR 21 • CE Standards (EN 50130-4) • EN41003 Telecoms The equipment has been approved to {Council Decision 98/482/EC} for Pan -Europe...