Hobart Q Series - Manuals - manualsarea.com

Page 2 - UNPACKING AND ASSEMBLY

– 2 – Installation, Operation and Care of Q SERIES REACH-IN FOOD STORAGE CABINETS SAVE THESE INSTRUCTIONS GENERAL The Q Series Reach-In Food Storage Cabinets are available as low temperature (0°F), mediumtemperature (38°F) refrigeration units or hot food storage cabinets (180°F maximum). They may be...

Page 4 - LEGS OR CASTERS; To install the legs, raise and block the reach-in a minimum of 7; Curb

– 4 – LEGS OR CASTERS WARNING: THE CABINET MUST BE BLOCKED AND STABLEBEFORE INSTALLING LEGS OR CASTERS. Legs (Fig. 5) To install the legs, raise and block the reach-in a minimum of 7 " from the floor and thread the legs into the Threaded Holes on the bottomof the cabinet. This unit must be level...

Page 5 - OPERATION

– 5 – Compressor Mounts Some Q Series units have the compressor specially mounted to help prevent damage during shipment.If the compressor is mounted on shipping blocks, remove the shipping blocks before operating thecompressor. If the compressor is mounted on springs, refer to the tag attached to t...

Page 7 - E L E C T RO N I C D E F RO S T T I M E R ( w h e n e q u i p p e d ); AM; and 8; PM; . The factor y preset defrost schedule; PROGRAMMING THE ELECTRONIC DEFROST TIMER

– 7 – E L E C T RO N I C D E F RO S T T I M E R ( w h e n e q u i p p e d ) If your freezer is equipped with an electronic Defrost Timer, it islocated in a control box behind the trim rail at the top of theReach-In Freezer. To access the the Defrost Timer, remove theThumbscrew on the left side of th...

Page 8 - Setting the Time Clock to the Current Time-of-Day; • The upper set of switches sets the HOUR. Slide the switch that; Setting the Defrost Duration; corresponds to the desired Defrost Duration (nearest 5 minutes).

– 8 – To Change the Defrost Duration and Bypass the Setting of the Time Clock Begin with the SET CLOCK light blinking rapidly, indicating normal Operation Mode . . .If you want to change the Defrost Duration but not reset the time-of-day, press and hold the PROGRAMbutton for about 3 seconds until th...

Page 9 - How to Set a Custom Defrost Schedule; For example, to start a defrost cycle at 2:30; OFF G

– 9 – How to Set a Custom Defrost Schedule Begin with the defrost timer on normal Operation Mode: The SET CLOCK light is blinking rapidly andthe PROGRAM and DEFROST ON lights are off. If all switches are OFF (Fig. 15), the factory presetdefrost schedule is enabled: 2 AM , 8 AM , 2 PM , 8 PM . • Dete...

Page 10 - Program Review; The SET CLOCK light blinks from 1 to 12 times to indicate the; Initiating a Manual Defrost

– 10 – Program Review During normal Operation Mode, with the SET CLOCK light blinking rapidly . . . Press the SET button until the SET CLOCK, PROGRAM, andDEFROST ON lights are lit; then release the SET button and allthree lights go off for two seconds. After that, all three lights beginto blink. The...

Page 11 - If the Defrost Timer's Battery Loses Power

– 11 – If the Defrost Timer's Battery Loses Power If the SET CLOCK, PROGRAM and DEFROST ON lights are all blinking, the backup power supply(batter y) to the Defrost Timer has weakened. Estimated batter y life is 10 years. The timer cancontinue to function normally after the batter y has weakened if ...

Page 12 - SYMPTOM

– 12 – FORM 14580 Rev. L (Jan. 2002) PRINTED IN U.S.A. MAINTENANCE CLEANING Cabinet Clean the inside of the cabinet and the doors weekly with a warm water solution of mild household liquiddishwashing detergent (such as Palmolive green or Ivory). Do not use anything containing grit,abrasive materials...