Hobart CE6HD ML-138010, CE10HD ML-138012, CE10FD ML-138016, CE20HD ML-138014, CE20FD ML-138018, CE6HD ML-138011, CE10HD ML-138013, CE10FD ML-138017, CE20HD ML-138015, CE20FD ML-138019 Manual

Page 2 - TABLE OF CONTENTS

– 2 – ©HOBART, 2007 TABLE OF CONTENTS GENERAL ..............................................................................................................................................................3INSTALLATION .....................................................................................

Page 3 - INSTALLATION, OPERATION AND CARE OF; SAVE THESE INSTRUCTIONS; GENERAL; bold; INSTALLATION; UNPACKING

– 3 – INSTALLATION, OPERATION AND CARE OF ELECTRIC COMBI, CONVECTION & STEAM OVENS SAVE THESE INSTRUCTIONS GENERAL The Electric Combi, Convection & Steam Ovens are single compartment ovens that provide convection heating and/or steaming in the cooking chamber. The Hobart C ombi E lectric ove...

Page 5 - motor rotation. The fan will rotate in the proper direction.; VENT HOOD; Before using the oven for the; Model

– 5 – DRAIN CONNECTION In order to avoid any back pressure in the oven, do not connect solidly to any drain. Extend the drain line from the 1" NPT drain pipe extending from the bottom of the oven at the rear to an open gap-type drain. Drain piping must have suitable pitch, have appropriate suppo...

Page 6 - OPERATION; DOOR SWITCH

– 6 – Fig. 1 OPERATION The oven and its parts are hot. Use care when operating, cleaning or servicing the oven. The cooking compartment contains live steam. Stay clear when opening door. DOOR SWITCH The oven is equipped with a feature that shuts off power to the oven cavity when the door is opened. ...

Page 7 - HANDLE

– 7 – Fig. 3 UNLOADING THE OVEN Unloading 6 or 10 Level Ovens Open door partially to allow hot air and steam to escape. Remove the product from the rack guides or racks in the oven. Close the door. Unloading 6 or 10 Level Ovens With Landing Table And Removable Insert Open door partially to allow hot...

Page 8 - CONTROL PANEL BUTTONS

– 8 – CONTROL PANEL BUTTONS ON/OFF Button Press this button to turn the oven on or off. Convection Mode Press this button to set the oven to Convection Mode. The button will illuminate to indicate it has been selected. Steam Mode Press this button to set the oven to Steam Mode. The button will illum...

Page 9 - DISPLAY SCREEN ICONS; 4 E X A M P L E

– 9 – DISPLAY SCREEN ICONS 44 E X A M P L E Program Number (Name) This indicates the current program number, if used. PH 1 / 1 0 Cooking Phase This indicates the cooking phase in progress. The oven can be set from 1 to 10 phases. START Delayed Preheat Timer This icon indicates that the oven has a de...

Page 10 - SETTING THE TEMPERATURE; SETTING THE INTERNAL CLOCK; fl

– 10 – SETTING THE TEMPERATURE 1. Select the cooking mode by pressing the Convection, Steam or Convection and Steam (Combi) Button(s). 2. Press the Selection Line Button next to the Temperature icon. The icon will be highlighted to indicate that it has been selected and the set temperature will be s...

Page 11 - SETTING THE VENT POSITION

– 11 – SETTING THE HUMIDITY 1. Select Combi Mode by pressing the Convection Button and Steam Button. 2. Press the Selection Line Button next to the Humidity icon. The icon will be highlighted to indicate that it has been selected and the set humidity will be shown. 3. Use the Plus/Minus Buttons to a...

Page 13 - PREHEATING THE OVEN

– 13 – SELECTING THE COOKING MODE After selecting one of the cooking modes, the default temperature for that cooking mode is displayed. The oven cavity lights will be on (only if the door is closed). USING CONVECTION MODE 1. If the screen is blank (sleep mode), turn on the oven by pressing the ON/OF...

Page 14 - USING STEAM MODE; USING COMBI MODE

– 14 – USING STEAM MODE 1. If the screen is blank (sleep mode), turn on the oven by pressing the ON/OFF Button. 2. Press the Steam Button to select steam mode. The button will illuminate to indicate it has been selected. 3. Set the oven temperature. 4. Set the timer. 5. Set the fan speed. NOTE: Preh...

Page 15 - TEMPERATURE PROBE; The probe temperature de; nal internal temperature with maximum product yield.

– 15 – TEMPERATURE PROBE The probe temperature de fi nes the fi nal temperature of the product for any cooking phase. The oven cooking cycle stops when the product temperature reaches the probe temperature setting. Total cooking time is not known or entered when using the probe. There are two ways t...

Page 16 - USING THE PRODUCT TEMPERATURE PROBE

– 16 – Setting the Cooking Core Probe Temperature 1. Insert the pointed end of the core probe into the product so that the tip is approximately in the middle of the product to be cooked. 2. Load the product into the oven. 3. Run the probe cable out the side of the door opening and close the door. 4....

Page 18 - WRITING A COOKING PROGRAM

– 18 – WRITING A COOKING PROGRAM It is possible to write and store up to 100 cooking programs with a maximum of 10 phases each. NOTE: The oven is also equipped to use an optional HCPC-HACCP recording system to facilitate fast, easy and accurate data management via wireless communication to a PC. Con...

Page 20 - AM

– 20 – USING A COOKING PROGRAM 1. Press the Program Button to select program mode. The button will illuminate to indicate it has been selected. 2. Use the Plus/Minus Buttons to select the program number to be used. The screen will display the fi rst phase of the program. 3. Press the START/STOP Butt...

Page 21 - DISPLAY SCREEN CLEANING AND SHUTDOWN ICONS; MAINTENANCE; SERVICE ADJUSTMENTS; CLEANING; Daily Cleaning

– 21 – DISPLAY SCREEN CLEANING AND SHUTDOWN ICONS STOP Stop Only Select this feature if the oven will be shutdown and not cleaned. Manual Clean Cycle Select this feature if the oven cavity is to be cleaned manually. Auto Clean Cycle Select this feature if the oven cavity is to be cleaned automatical...

Page 22 - Automatic Clean Cycle; Quick Rinse Cycle

– 22 – Automatic Clean Cycle NOTE: Before using the auto clean cycle, make sure that the detergent pump tube is inserted correctly into the detergent container and that enough detergent is available. 1. Press the Selection Line Button next to the Auto Clean Cycle icon. 2. Use the Plus/Minus Buttons ...

Page 23 - TROUBLESHOOTING; SERVICE AND PARTS INFORMATION; FAULT SYMBOLS CHART; AUTODIAGNOSTICS

– 23 – TROUBLESHOOTING SERVICE AND PARTS INFORMATION Contact your local Hobart Service of fi ce for any repairs or adjustments needed on this equipment. FAULT SYMBOLS CHART 00 Electronic components overheat (CPU) 01 Cavity overheat 02 Not used 03 Cavity probe fault 04 Not used 05 Not used 06 Not use...

Page 24 - SERVICE PARAMETER SETUP; SYSTEM PARAMETER FUNCTIONS; Parameter

– 24 – FORM 35474 (July 2007) PRINTED IN U.S.A. SERVICE PARAMETER SETUP The internal settings of the combi oven can be customized to fi t your own personal needs. The chart below is provide to show you what functions can be modi fi ed. All system modi fi cations must be made by an authorized Hobart ...