Hobart LX18 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

– 2 – © HOBART CORPORATION, 1993 TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3 - LX SERIES DISHWASHERS; SAVE THESE INSTRUCTIONS; GENERAL; MODEL

– 3 – Model LX30 Dishwasher Installation, Operation, and Care of LX SERIES DISHWASHERS SAVE THESE INSTRUCTIONS GENERAL The LX Series dishwashers are fully automatic, front-loadingd i s h w a s h i n g m a c h i n e s w h i c h a r e e q u i p p e d w i t h a 3 / 4 horsepower electric motor. All LX S...

Page 4 - INSTALLATION; UNPACKING; ater

– 4 – INSTALLATION UNPACKING Immediately after unpacking the dishwasher, check for possible shipping damage. If this machine isfound to be damaged, save packaging material and contact the carrier within 15 days of delivery. Prior to installation, verify that the electrical supply agrees with the spe...

Page 5 - A drain hose is provided with a; Water Supply; Water supply requirements are as follows:; F Minimum

– 5 – PLUMBING CONNECTIONS WARNING: PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY,AND PLUMBING CODES. Drain A drain hose is provided with a 3 / 4 " pipe connection adapter. This should be securely plumbed into the sink drain. Use care not to kink hose. See installation diagra...

Page 6 - ELECTRICAL CONNECTION

– 6 – ELECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THEAPPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCALELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING O...

Page 8 - DETERGENT AND RINSE AID

– 8 – DETERGENT AND RINSE AID If manually adding detergent in an LX18, LX18C, or LX18H at the beginning of each cycle, the machinemust be programmed to the “True Fill and Dump” mode. This will ensure detergent is not dumpedbefore filling with fresh, hot water. Contact your local Hobart Service Offic...

Page 12 - OPERATION; BEFORE FIRST USE

– 12 – OPERATION CAUTION: Items such as pewter, aluminum, and silver will be attacked by sodium hypochlorite(bleach). Therefore, chemical sanitizing dishwashers should not be used to wash such items. If your dishwasher is a chemical sanitizing model, frequently check the clear portion of your chemic...

Page 15 - WASH/RINSE CYCLE TIMES; Wash

– 15 – MODELS LX30, LX30C and LX30H WASH/RINSE CYCLE TIMES Wash 85 Sec.** Drain* 10 Sec. Max. Dwell 4 Sec. Rinse 10 Sec. Dwell 6 Sec. * Drains off about 1 gallon of water.**Wash time is 145 seconds for 70 ° F rise option.

Page 19 - To exit the manager programming mode do one of the following:

– 19 – MANAGER PROGRAMMING (Machine Must Be In READY Mode) To enter the Manager Programming Mode, you must first enter the Operator Programming Mode bypressing and holding "LX40" on the control panel (this is the HIDDEN key), then pressing WASH.Once you are in the Operator Programming Mode, ...

Page 22 - NOT use abrasive or harsh cleaners or scouring pads.; CLEANING — ALL MODELS

– 22 – 3. With a damp cloth, wipe the interior of the machine, the water level probes (Fig. 9), and the water level probe under the fine strainer. DO NOT use steel wool. Wipe the exterior of the machine.When cleaning the inside of the door, be sure to wipe the lip at the bottom of the door. Removean...

Page 23 - MAINTENANCE; DELIMING — GENERAL

– 23 – MAINTENANCE DELIMING — GENERAL WARNING: DELIMING SOLUTION, RINSE AGENTS, OR ANY OTHER KIND OF ACID MUST NOTCOME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED IN CHEMICALSANITIZING MACHINES. MIXING MAY CAUSE HAZARDOUS GAS TO FORM. THIS ENTIREPROCEDURE MUST BE FOLLOWED STEP-BY...

Page 25 - DELIMING — Models LX40H and LX40C; and power to the control will be turned off.; LUBRICATION

– 25 – DELIMING — Models LX40H and LX40C Models LX40H and LX40C are equipped with an automatic delime cycle reminder. After thepreprogrammed number of cycles has expired, the control will indicate the delime request byilluminating DELIME. At this point, you must either enter a delime cycle or reprog...

Page 26 - TROUBLESHOOTING; SYMPTOM

– 26 – TROUBLESHOOTING This section outlines various symptoms and possible causes that may be encountered in the event ofabnormal machine operation. If symptoms persist after possible causes have been checked, servicemay be required. SYMPTOM POSSIBLE CAUSES No machine operation 1. Machine OFF — turn...