Hobart DRO2G - Manuals - manualsarea.com

Page 3 - Table of Contents

– 3 – Table of Contents GENERAL ............................................................................................................................................... 4 INSTALLATION ................................................................................................................

Page 4 - PLEASE KEEP THIS MANUAL FOR FUTURE USE; GENERAL

– 4 – OPERATION and CARE of MODELS DRO2G & DRO2GH GAS RACK OVENS WITH ELECTRONIC OVEN CONTROL PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Models DRO2G and DRO2GH Gas ovens accommodate roll-in racks. They are equipped with anelectronic oven control for baking and/or steaming applications. A me...

Page 5 - OPERATION; BEFORE FIRST USE

– 5 – OPERATION WARNING: THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING,SERVICING OR CLEANING THE OVEN. BEFORE FIRST USE Before using the oven for the first time, it must be burned in to release any odors that might result fromheating the new surfaces in the oven. W A R N I N G : D I S...

Page 7 - DOOR HANDLE

– 7 – DOOR HANDLE When the door is closed, make sure the door handle is in the fully vertical position (Fig. 2). Fig. 2 CONTROLS (Fig. 3) All of the oven’s baking processes are controlled here. Whether you bake in manual baking mode orprogram a baking process and recall it from memory, the same para...

Page 12 - MANUAL BAKING

– 12 – MANUAL BAKING Program # 0 is used for manual baking processes that are not assigned to memory. 1. Press the PROGRAM # UP arrow key to 0. If the PROGRAM # UP arrow key does not change the program number, press OFF and BAKE to reset and begin again. Program # 0 is factorypreset as follows: • SE...

Page 14 - CLEANING

– 14 – OVEN VENT CONTROLS When changing to a product which requires a lower baking temperature, the oven can be cooled downby exhausting heat from the oven using the Vent. To cool down the oven, open the Damper by pullingthe knob outward (Fig. 4). Fig. 4 OVEN PRESET VALUES • The maximum SET TEMPERAT...

Page 15 - MAINTENANCE

– 15 – MAINTENANCE WARNING: THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING,SERVICING, OR CLEANING THE OVEN. W A R N I N G : D I S C O N N E C T E L E C T R I C A L P O W E R T O T H E M A C H I N E A N D F O L L O WLOCKOUT / TAGOUT PROCEDURES. G E N E R A L As Needed • Inspect the area...

Page 16 - PREVENTIVE MAINTENANCE

– 16 – LUBRICATION None required. SERVICE AND PARTS INFORMATION Contact your local authorized Hobart office for service . PREVENTIVE MAINTENANCE The DRO2 oven should be kept on a regular preventive maintenance schedule. Ovens require specificpreventive maintenance based on usage and environmental fa...

Page 17 - OWNER PREVENTIVE MAINTENANCE PROCEDURE; INTRODUCTION

– 17 – OWNER PREVENTIVE MAINTENANCE PROCEDURE INTRODUCTION This owner preventive maintenance (PM) section includes procedures to inspect for proper operationand cleaning of components. Owner Preventive Maintenance Procedures are written for gas ovens.They can also be used for electric ovens by omitt...

Page 18 - Clean and Vacuum Components and Burner Areas; Inspect Rack Lift and Rotation Assemblies

– 18 – Clean and Vacuum Components and Burner Areas 1. Clean the burner compartment (Fig. 6) area of dust and/or lint accumulation. 2. Vacuum the burner compartment (Fig. 6) floor of dust and/or lint accumulation. 3. Check and clean all air passageways (Figs. 7 & 8). A. Clear objects blocking al...

Page 19 - Inspect Door Components; Inspect Air Louvers

– 19 – Inspect Door Components 1. Verify door switch operation (Fig. 9). A. Open door. B. While watching the door switch (at top of oven), close the door. C . The door switch should be operated. D . With the door open, the switch should be un-operated. 2. Check loading door latch bushings. A. Open d...

Page 21 - Verify Ignition Module Safety Lockout Functions - cont.

– 21 – Verify Ignition Module Safety Lockout Functions - cont. 3. Reset control after safety lockout. A. With the control in a lockout condition, turn the main gas valve on. B. Reset the control by turning the oven control off and then back on. C . Ignition module should perform the 30 second purge ...