Henny Penny OE-100 - Manuals

Page 2 - Henny Penny; THERMAL SENSOR; NOTE

Henny Penny Model OE-100 2-2 2-4. THERMAL SENSOR The thermal sensor determines the shortening temperature. If a mal-function does occur, an E6 will be displayed on the digital readout.Turn unit to OFF position, then back to COOK position. If E6 is stilldisplayed, the thermal sensor must be replaced ...

Page 3 - thermal sensor bulb straight out from pot fitting.

2-3 Henny Penny Model OE-100 2-5. HIGH TEMPERATURELIMIT CONTROL The high temperature limit control is a manual reset control whichsenses the temperature of the shortening. If the shortening temperatureexceeds the safe operating limit, this control will open and shut off theheat to the frypot. The hi...

Page 5 - HEATING ELEMENTS

2-5 Henny Penny Model OE-100 2-6. HEATING ELEMENTS NOTE Heating elements are available for 208 and 480 voltage.Check the data plate to determine the correct voltage. If the shortening's temperature recovery is very slow or at aslower rate than required, this may indicate defective heatingelement(s)....

Page 6 - Replacement

Henny Penny Model OE-100 2-6 2-6. HEATING ELEMENTS(Continued) 1091 Replacement 1. Drain the shortening from the frypot. 2. Remove the heating element wire from the terminals by removing the nuts and washer. Label each so it can be replaced in the sameposition on the new element. 3. Remove the retain...

Page 8 - FAN

Henny Penny Model OE-100 2-8 2-8. FAN The Henny Penny OE-100 has a fan in the circuit which operates onlywhen the power switch is in the COOK position. The fan helps keepthe control panel cool by pulling out heat from between the controlpanel and frypot. The replacement of a faulty fan is as follows...

Page 9 - Remove the four screws, washers, and nuts securing the fan to the; Checkout; With control panel removed and wires off the switch, push in on

2-9 Henny Penny Model OE-100 2-8. FAN (Continued) 2. Label and disconnect fan motor wires. 3. Remove the four screws, washers, and nuts securing the fan to the heat shield. 4. Remove the fan from the heat shield. 5. Install the new fan on the heat shield and secure with the four screws, washers, and...

Page 11 - SWITCH; Remove electrical power supplied to unit.

2-11 Henny Penny Model OE-100 2-12. FILTER HEATER SWITCH Checkout The Filter Heater Switch is a rocker type switch. With the switchin the "ON" position, the filter heater will operate, melting anysolidified shortening in the filter lines. 1. Remove electrical power supplied to unit. Remove e...

Page 12 - Open panel board and cut wires at the connectors which go to

Henny Penny Model OE-100 2-12 2-13. FILTER HEATER 593 This unit is equipped with a strip heater in the event solidified shorten-ing accumulates in the filter pump lines. If this heater becomes defec-tive, replace by following these steps. Remove all power from unit. Failure to do so could resultin e...

Page 13 - Installation

2-13 Henny Penny Model OE-100 2-14. FILTERING SYSTEM The filtering system consists of the filter valve, motor and filter pumpassembly, filter screen assembly, and tubing. Shortening with temperature in excess of 200 OF flowsthrough this filter rinse hose. Heat causes the rubber hoseto age and deteri...

Page 14 - REPAIR

Henny Penny Model OE-100 2-14 2-15. FILTER VALVE The filter valve is a 3/8 inch two-way stainless steel ball valve. If thisvalve should develop leaks the entire valve must be replaced. To avoid electrical shock or other injury before starting thisprocedure move COOK/PUMP SWITCH to OFF position.Disco...

Page 15 - To reassemble, place rotor on drive shaft, and place rollers into; If the pump needs to be replaced, loosen one inch nuts from the

2-15 Henny Penny Model OE-100 2-16. FILTER PUMP REPAIR (Continued) 3. To reassemble, place rotor on drive shaft, and place rollers into rotor. NOTE A small amount of shortening might be needed to hold thebottom roller into place until cover plate is put on. Make sureO-ring is in proper position on p...

Page 16 - REPLACEMENT

Henny Penny Model OE-100 2-16 2-18. PUMP AND MOTOR REPLACEMENT 1. To replace the pump and motor assembly, insure the main power has been removed from the fryer. To avoid electrical shock, injury or burns before startingthis procedure move COOK/PUMP SWITCH to OFFposition. Disconnect main circuit brea...