Henny Penny FM07-020-F - Manuals

Page 3 - LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT

FM07-020-F Revised 08-31-07 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT: Any part of a new appliance, exce...

Page 4 - Table of Contents; Henny Penny Distributor List (Domestic and International)

Table of Contents SECTION 1. INTRODUCTION .................................................................................................... 1-11-1. SAFETY ......................................................................................................... 1-1 1-2. ASSISTANCE ...................

Page 5 - SECTION 1. INTRODUCTION; NOTICE is used to highlight especially important information.

SECTION 1. INTRODUCTION 1-1. SAFETY The Henny Penny pressure fryer has may safety features incorporated.However, the only way to ensure a safe operation is to fully under-stand the proper installation, operation, and maintenance procedures.The instructions in this manual have been prepared to aid yo...

Page 6 - REMOVAL; A. Remove the four screws holding the existing control panel in; Wire

1-3. INTRODUCTION Installation of the KFC Computerized Control Panel on existingHenny Penny gas pressure fryers. Disconnect the fryer from the electrical supply sourcebefore beginning panel conversion. Failure to disconnect the fryer from the supply sourcecould result in electrical shock. The fryer ...

Page 7 - Excess force will damage the probe.

1-5. NINE-PIN CONNECTOR WIRING A. Remove the above wires from their existing position. These wires will be connected to the nine-pin connector provided. B. Locate wires number 12, 8, and 11 at the fan motor. Remove the connector securing these wires. Wire number 11 can bediscarded at this time. Wire...

Page 8 - INSTALLATION

1-7. SLOT COVER When installing the computerized panel retrofit kit, it is necessaryto cover the existing slot in the heat shroud. This slot allows thecapillary tube of the old control panel to extend through the heatshroud when mounting the old control. A. Open door and push slot cover through shro...

Page 9 - FIGURE 1

Page 10 - FIGURE 2

Page 16 - SHORTENING; Turn the main power switch to the OFF position.

2-6. FILTERING THE SHORTENING Frying breaded products requires frequent filering. After eachfrying cycle the display will read FILR, indicating to filter. It should benoted that further operation of the control is not allowed until filteringis complete. Clean and filter the frypot as follows. 1. Tur...

Page 19 - SECTION 3. PROGRAMMING; SEQUENCE

SECTION 3. PROGRAMMING 3-1. BASIC PROGRAMMING SEQUENCE To enter the program mode a password keystroke sequence isrequired. Note that when performing this sequence the switchesmust be depressed within one second of each other. If not,the control will not enter the program mode. 1. Depress the “SELECT...

Page 20 - PROGRAMMING MODES; Enter the password keystroke sequence for programming

3-2. COOK CYCLE PROGRAMMING(Continued) 10. Follow steps 4, 5, and 6 until all six intervals have been programmed for pressure. The above steps may be followed for interval alarmsexcept you cannot program an interval alarm in thefirst interval. Refer to Special Programming Modes on factorypresets for...

Page 21 - PARAMETERS; Depress the cycle 6 switch. Display will read as follows.

3-4. SPECIAL PROGRAMMING MODES(Continued) 3. Select the desired special function by depressing either cycle switch 6 or 7. 4. Perform the desired operation. 5. Depress the EXIT FILL switch to exit the special program mode. Unit will return to stand-by cook mode. The preceding steps must be followed ...

Page 22 - When programming one step KFC parameters, load compen-; Load Compensation; - Load compensation adjusts cooking; Proportional Control; - Proportional control regulates pot tempera; Filter Cycle; - Filter indication is given after the programmed

3-6. TEST PROCEDURE (Continued) The table below shows the corresponding switch with theoutput. Switch Device Activated Product One Pressure Solenoid and Heat Control Select Time Product Indicators Select Function Function Indicators Change Switch Under Display 4 Change Switch Indicator Display Chang...