Heat & Glo st-42tvfl - Manuals

Heat & Glo st-42tvfl – Manual in PDF format online.

Manuals:

Manual

Manual Heat & Glo st-42tvfl

Summary

Page 2 - SAFETY AND WARNING INFORMATION; Owners Guide; ALERTED; Installers Guide; DO NOT

2 ! SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Firep...

Page 3 - Section 4: Maintaining and Servicing

3 Table ofContents Safety and Warning Information ....................2 Service Parts List ...............................................4 Section 1: Approvals and Codes ................ 10 Appliance Certification .......................................... 10 Installation Codes .......................

Page 4 - Service Parts

4 * Part number list on following page.* La liste des numéros de pièce se trouve à la page suivante. 7 Log Assembly 2 5 1 3 4 6 u (NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des pièces Service Parts PIER-TVFL, PIER-TVFL-DSI 8 9 MANUFACTURING DATESSP Beginning: 8-97, Ending Date: ___DSI Begin...

Page 5 - L'information fournie dans cette brochure; STANDING PILOT IGNITION ONLY / ALLUMAGE UNE VEILLEUSE SEULEMENT

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est valide que pendant une courte période. Les sites VIP...

Page 8 - PIÈCE; Standing Pilot Ignition

8 (NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des pièces Service Parts Beginning Manufacturing Date: 10-97 Ending Manufacturing Date: ______ ITEM / PIÈCE DESCRIPTION SERIAL # / N° DE SÉRIE PART NUMBER / N° DE PIÈCE 1 Valve NG / Valve GN 060-522 1 Valve LP / Valve PL 060-523 2 ON/OFF Rocker S...

Page 9 - Direct Spark Ignition

9 (NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des pièces Service Parts ITEM / P I È C E DESCRIPTION SERIAL # / N° DE SÉRIE PART NUMBER / N° DE PIÈCE 1 Junction Box / Boîtier de dérivation 100-254A 2 ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT 060-511 3 Burner Tube / Tube de br...

Page 10 - Appliance Certification; CERTIFICATION; Installation Codes

10 Heat-N-Glo QualitySystems registeredby SGS ICS Approval Listingsand Codes Appliance Certification The Heat-N-Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. CERTIFICATION MODEL LABORATORY TYPE STANDARD ...

Page 11 - Do

11 2 GettingStarted Introducing theHeat-N-GloGas Fireplaces Heat-N-Glo B-type vent gas fireplaces are designed to operate with all exhaust gases expelled to the outsideof the building. The information contained in this Installers Guide , unless noted otherwise, applies to all models and gascontrol s...

Page 12 - Where the unit is to be installed.

12 24 1/4 (616mm) 40 3/4 (1035mm) 36 7/8 (937mm) 36 7/8 (937mm) 41 (1043mm) 24 1/4 (616mm) 12 1/8 (308mm) 21 5/8 (551mm) VENT COLLAR ELECTRICAL ACCESS 2 1/2 (64mm) 4 (102mm) 4 (102mm) 2 1/2 (64mm) GAS LINEACCESS LEFT SIDE FRONT RIGHT SIDE 1/2" STANDOFFS TOP STANDOFFS ELECTRICAL ACCESS GAS LINE A...

Page 14 - Clearance Requirements; The metal end(s) of these fireplaces may

14 Figure 3. Fireplace Locations and Space Requirements Clearance Requirements The top, back, and sides of the fireplace are definedby stand-offs. Minimum Clearances from the Fireplace to Combustible Materials Glass Back of Metal Ends Top of Sides Floor Fireplace of Fireplace Fireplace Ceiling* 36 i...

Page 15 - CAUTION; Figure 5. Framing Dimensions

15 MODEL A B C PIER 40 1 / 4 23 1 / 4 41 1 / 2 ST-42TVFL 44 23 1 / 4 41 1 / 2 Minimum Clearances from the B-Type Vent Pipeto Combustible Materials is 1 inch (25 mm) allaround the pipe. Step 2Framing theFireplace Fireplace framing can be built before or after thefireplace is set in place. Framing sho...

Page 17 - Air Damper

17 Detailed installation instructions for Model AK-TVOutside Air kit are found in the kit. Air Damper Before lighting the burner, open the damper plate bysliding the air damper rod, located by the gas valve,towards you. Figure 5. Make-up Air DUCT COLLAR DAMPER ASSEMBLY

Page 19 - Figure 6. Vent System Attachment

19 Figure 6. Vent System Attachment ! WARNING: THIS GAS FIREPLACEMUST NEVER BE VENTED BYCONNECTING T O A CHIMNEY FLUESERVING A SEPARATE SOLID FUELBURNING APPLIANCE. 4 FT. MINIMUM 17 FT. MAXIMUM MAXIMUM HORIZONTAL RUN 4 FT MINIMUM 10 FT. MINIMUM

Page 20 - C. Bedroom Installation in Canada; This model; MUST NOT; be vented into a vent; ROOF PITCH; Figure 7. Vent Termination

20 C. Bedroom Installation in Canada This model MUST NOT be vented into a vent system installed exterior to a building. The part ofthe vent system above the roof line can be exteriorto the building. D. Vent Termination WARNING: MAJOR U.S. BUILDINGCODES SPECIFY MINIMUMCHIMNEY AND/OR VENT HEIGHTABOVE ...

Page 21 - Securing of a Fireplace

21 The diagram below shows how to properly position,level, and secure the fireplace. 1. Place the fireplace into position. 2. Level the fireplace from side to side andfrom front to back. 3. Shim the fireplace with non-combustiblematerial, such assheet metal, asnecessary. 4. Secure the fireplace to t...

Page 22 - Figure 9. Gas Controls Systems; DO NOT USE AN OPEN FLAME TO

22 STANDING PILOT DSI IGNITION Figure 9. Gas Controls Systems Step 7The GasSupply Line N O T E : Have the gas supply line installed i naccordance with local building codes by a qualifiedinstaller approved and/or licensed as requiredb y t h e l o c a l i t y . ( I n t h e C o m m o n w e a l t h o fM...

Page 24 - Figure 11. Standing Pilot Ignition Wiring Diagram; For Standing Pilot Ignition Wiring; This appliance; DOES NOT

24 Figure 11. Standing Pilot Ignition Wiring Diagram ! ! Step 9Wiring theFireplace NOTE: Electrical wiring must be installed by alicensed electrician. Caution: Disconnect remote controls if you areabsent for extended time periods. This willprevent accidental fireplace operation. For Standing Pilot I...

Page 26 - Figure 13. Minimum Vertical and Maximum

26 ! Step 10Finishing The following diagram shows the minimum verticaland corresponding maximum horizontaldimensions of fireplace mantels or othercombustible projections above the top front edgeof the fireplace. See Figures 3 and 4 for otherfireplace clearances. Only non-combustiblematerials may beu...

Page 27 - Figure 14. Sealant Material; Hearth Extensions; do not; require hearth extensions for gas; Installing the Trim; MUST NEVER; overlap onto the; Positioning the Logs

27 Step 11Installing Trim,Logs, and EmberMaterial 1. Apply only non- combustible facingmaterial to thefireplace surround. Figure 14. Sealant Material Hearth Extensions A hearth extension may be desirable for aestheticreasons. However, ANSI or CAN/CGA testingstandards do not require hearth extensions...

Page 30 - IMPORTANT

30 4 MaintainingandServicingYourFireplace FireplaceMaintenance Although the frequency of your fireplace servicingand maintenance will depend on use and the type ofinstallation, you should have a qualified servicetechnician perform an appliance check-up at thebeginning of each heating season. See the...

Page 31 - DSI IGNITION; Figure 16. Burner Flame Patterns; STANDING PILOT

31 NOTE: FLAMESTOO CLOSE TOTHE CERAMICINSULATORS CANCAUSE NUISANCELOCKOUTS ANDELECTRODEFAILURE. DSI IGNITION Figure 16. Burner Flame Patterns MAKE SURE THE FLAMESARE STEADY—NOTLIFTING OR FLOATING. Figure 17. Ignitor Flame Patterns STANDING PILOT 3/8" (10mm) IGNITOR CERAMICINSULATOR 3/32" 3/8...