Heat & Glo 8000TVD - Manuals

Heat & Glo 8000TVD – Manual in PDF format online.

Manuals:

Manual

Manual Heat & Glo 8000TVD

Summary

Page 2 - DO NOT; ALERTED; SAFETY AND WARNING INFORMATION

2 These units MUST use one of the vent systems described in the Installing the Fireplace section ofthe Installers Guide . NO OTHER vent systems or components M AY BE USED . This gas fireplace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached to a chimney serving a s...

Page 3 - TABLE OF CONTENTS; Safety and Warning Information

3 TABLE OF CONTENTS Safety and Warning Information . ................................................ 2 Service Parts List . ....................................................................... 4 Section 1: Approvals and Codes . ............................................... 8 Appliance Certific...

Page 4 - * La liste des numéros de pièce se trouve à la page suivante.; Log Set Assembly; Service Parts

4 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 10 11 12 13 14 16 15 17 4 6 2 1 3 8 7 9 Log Set Assembly 18 5 (NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des pièces Service Parts 8000TVD Beginning Manufacturing Date: 9-97 Ending Manufactu...

Page 5 - COMMON PARTS / PIÉCES COMMUNES

5 (NG, LP) Service Parts List / (GN, PL) Liste des pièces de rechange ITEM / PIÈCE ENGLISH / FRENCH DESCRIPTION SERIAL # / N° DE SÉRIE PART NUMBER / N° DE PIÈCE COMMON PARTS / PIÉCES COMMUNES 1 Junction Box - Pilot / Boîtier de raccordement - de veilleuse PRE 002324001POST 002324001 100-250A 4021-01...

Page 6 - Standing Pilot Ignition

6 (NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des pièces Service Parts Beginning Manufacturing Date: 9-97 Ending Manufacturing Date: ______ ITEM / PIÈCE DESCRIPTION SERIAL # / N° DE SÉRIE PART NUMBER / N° DE PIÈCE 1 Pilot Bracket / Parenthèse Pilote 530-164 2 ON/OFF Rocker Switch / Interrupt...

Page 7 - Intermittent Pilot Ignition

7 (NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des pièces Service Parts Beginning Manufacturing Date: 9-01_ Ending Manufacturing Date: ______ ITEM / PIÈCE DESCRIPTION SERIAL # / N° DE SÉRIE PART NUMBER / N° DE PIÈCE 1 Pilot Bracket / Parenthèse Pilote 530-164 2 ON/OFF Rocker Switch / Interrup...

Page 8 - Appliance Certification; The Heat-N-Glo fireplace model discussed in this; Certification; Underwriters Laboratories; Installation Codes

8 Appliance Certification The Heat-N-Glo fireplace model discussed in this Installers Guide has been tested to certification standards and listed by the applicable laboratories. Certification MODELS: 8000TVD LABORATORY: Underwriters Laboratories TYPE: Vented Gas Fireplace STANDARD: A N S I Z 2 1 . 5...

Page 9 - Getting Started; Introducing the Heat-N-Glo Gas Fireplaces; Pre-install Preparation; Do not install any

9 2 Getting Started Introducing the Heat-N-Glo Gas Fireplaces Heat-N-Glo B-type vent gas fireplaces are designed to op-erate with all exhaust gases expelled to the outside of thebuilding. The information contained in this Installers Guide , unless noted otherwise, applies to all models and gas contr...

Page 11 - Installing the Fireplace; Step 1. Locating the Fireplace; from the screw; Step 2. Framing the Fireplace; MEASURE FIREPLACE DIMENSIONS AND

11 3 Installing the Fireplace Step 1. Locating the Fireplace The diagram below shows space and clearance require-ments for locating a fireplace within a room. A B C D E 49” 22” 39 1/2” 56” 79” Minimum Clearances from the Fireplace to Combustible Materials Inches mm Glass Front .........................

Page 12 - Negative Pressure warning; : When negative pressure is; This may create a dangerous carbon; Stack effect in the building.; Air Damper

12 Step 3. Negative Pressure Make-up Air Negative Pressure warning : When negative pressure is present, an atmospherically vented fireplace (with a drafthood) may not function properly and it may down draft. Inthe case of a gas appliance, spillage of the combustiongases may occur. This may create a ...

Page 13 - and

13 ! ! Step 4. Installing the Vent System A. Vent System Approvals Model 8000TVD is approved to use 6-inch (152mm) diameterB-type vent. B-type vent must be used when the ventsystem is within combustible construction. These models may also use single wall rigid or flexible gasvent IF and ONLY IF the ...

Page 14 - Step 6. The Gas Control Systems

14 ! C. Bedroom Installation in Canada This model MUST NOT be vented into a vent system in- stalled exterior to a building. The part of the vent systemabove the roof line can be exterior to the building. D. Vent Termination WARNING: MAJOR U.S. BUILDING CODESSPECIFY MINIMUM CHIMNEY AND/OR VENTHEIGHT ...

Page 15 - Figure 9. Gas Supply Line; Step 7. The Gas Supply Line; Pressure; STANDING PILOT

15 Figure 9. Gas Supply Line • Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between thepipe and the outer casing. • At the gas line access hole the gap between the supply piping and gas access hole can be plugged with non-combustible insulation ...

Page 16 - Step 9. Wiring the Fireplace; This appliance; DOES NOT

16 Step 9. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensedelectrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB-SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE-VENT ACCIDENTA L FIREPLACE OPERATION. For Standing Pilot Ignition WiringAppliance Requirements • This appliance ...

Page 19 - Step 12. Before Lighting the Fireplace; Step 13. Lighting the Fireplace

19 Glass Specifications: TEMPERED Figure 16. Placement of the Ember Material Figure 15. Glass Assembly Step 12. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: Remove all paperwork from underneath the fireplace. Review safety warnings and cautions • Read the...

Page 20 - Maintaining and Servicing Your Fireplace; Fireplace Maintenance; Placing Ember Material

20 4 Maintaining and Servicing Your Fireplace Fireplace Maintenance Although the frequency of your fireplace servicing and main-tenance will depend on use and the type of installation, youshould have a qualified service technician perform an appli-ance check-up at the beginning of each heating seaso...