Garland H280 - Manuals - manualsarea.com

Page 3 - Once the springs are removed, the oven door will be free to fall.; Use a strong tape to; with no microswitch

03/09/09 P/N 4523367 Page 3 3) Unscrew Igniter Bracket  Unscrew the two screws holding down the igniter bracket to the orifice bracket. Left: Before removal, location of screws shown by arrows Right: After removal 4) Remove Door Springs  Once the springs are removed, the oven door will be free to ...

Page 5 - It is important that the; to prevent damage to the

03/09/09 P/N 4523367 Page 5  For the door hinge with a microswitch:  Unscrew the microswitch bracket from the oven frame. It is important that the microswitch be removed prior to removing the spring to prevent damage to the microswitch when the springs are reinstalled later. Microswitch bracket he...

Page 7 - Page 7; This step must be performed if a TS-11 valve was just removed.; Refer to the Assembly Drawing included in this manual

03/09/09 P/N 4523367 Page 7 6) Install Extension Fitting (if applicable)  If pilot gas tube going into the valve already has an extension piece (short piece of tubing plus 3/16” brass fitting), unscrew the shorter piece of tubing and proceed to Step 13. Otherwise, follow these steps to install the ...

Page 8 - will not; Left: Lower oven cavity after removal of front shields

03/09/09 P/N 4523367 Page 8 7) Remove Left and Right Front Shields  Both shields are attached to the upper support bar using 3 screws. Left: Left side front shield, location of screws shown by arrows Right: Right side front shield, location of screws shown by arrows 8) Remove Burner  Burner is not...

Page 10 - 1) Assemble New Pilot Assembly; BLACK

03/09/09 P/N 4523367 Page 10 11) Assemble New Pilot Assembly  A colored line on the top of the pilot indicates the type of fuel used. A BLACK line is used on a natural gas pilot, whereas a RED line is used on a propane pilot. Ensure the proper pilot is used.  Insert sheath onto new pilot assembly ...

Page 12 - all the way; 2) Attach New Pilot Assembly to Welded Bracket on New Burner

03/09/09 P/N 4523367 Page 12  Attach new Robertshaw thermocouple to pilot assembly  Push the thermocouple all the way into its slot on the pilot. Left: Wrong installation. Thermocouple not pushed all the way through socket. Right: Correct installation. Thermocouple pushed all the way through socke...

Page 13 - 3) Install New Burner; No screws are necessary for this procedure; New burner and pilot assembly installed

03/09/09 P/N 4523367 Page 13 13) Install New Burner  Ensure that the bracket at the tip of the burner locks onto the bracket attached to the oven floor. No screws are necessary for this procedure .  The burner may not stand up perfectly by itself. The installation of the oven orifice later will co...

Page 15 - 6) Reinstall Door Springs; Ensure that the button on the microswitch is

03/09/09 P/N 4523367 Page 15 16) Reinstall Door Springs  Refer to Step 4 for door spring connections  For the door hinge with no microswitch:  Hook on one end of the spring to the hooks from the orifice bracket  Place a screwdriver underneath the opposite end of the spring and pry upward to hook...

Page 17 - outlet; on the Baso valve

03/09/09 P/N 4523367 Page 17 19) Screw on Pilot Gas Flex Tube, Adjust Main Burner Gas Fitting  Remove the brass nut and ferrule originally on the pilot gas outlet on the Baso valve (Part 5 and Part 6, Assembly Drawing). Install them onto the free end of the flex tube.  Screw the pilot gas flex tub...

Page 18 - Baso Valve Ferrule

03/09/09 P/N 4523367 Page 18 20) Install New Pilot Gas Tube  If a new 3/16” fitting (Part 4, Assembly Drawing) was installed on the pilot gas tube (Part 3, Assembly Drawing), unscrew the nut on the free end of the fitting to release the nut and the ferrule. If a fitting was already installed on the...

Page 20 - Left: Unscrewing two lower screws of orifice bracket

03/09/09 P/N 4523367 Page 20 23) Attach Bracket to Oven For Standard Ovens:  Unscrew the two screws holding the orifice bracket to the lower oven frame.  Slip the bracket (Part 8, Assembly Drawing) underneath the valve assembly such that the taller face is flush up against the lower oven frame.  ...

Page 22 - Do not install this kick plate.; Right: New kick plate with slanted profile.

03/09/09 P/N 4523367 Page 22 25) Install New Kick Plate  The new kick plate (Part 14, Assembly Drawing) slants outwards to accommodate the valve. Ensure that the correct kick panel is installed. Left: Old kick plate with flat profile. Do not install this kick plate. Right: New kick plate with slant...

Page 23 - Installation Complete

03/09/09 P/N 4523367 Page 23 Installation Complete Installation Complete – Kick Plate Off Installation Complete – Kick Plate On