Garland H280 - Manual
Garland H280 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Once the springs are removed, the oven door will be free to fall.; Use a strong tape to; with no microswitch
- Page 5 – It is important that the; to prevent damage to the
- Page 7 – Page 7; This step must be performed if a TS-11 valve was just removed.; Refer to the Assembly Drawing included in this manual
- Page 8 – will not; Left: Lower oven cavity after removal of front shields
- Page 10 – 1) Assemble New Pilot Assembly; BLACK
- Page 12 – all the way; 2) Attach New Pilot Assembly to Welded Bracket on New Burner
- Page 13 – 3) Install New Burner; No screws are necessary for this procedure; New burner and pilot assembly installed
- Page 15 – 6) Reinstall Door Springs; Ensure that the button on the microswitch is
- Page 17 – outlet; on the Baso valve
- Page 18 – Baso Valve Ferrule
- Page 20 – Left: Unscrewing two lower screws of orifice bracket
- Page 22 – Do not install this kick plate.; Right: New kick plate with slanted profile.
- Page 23 – Installation Complete
03/09/09
P/N 4523367
Page 1
H280-series Valve Overheat / Relocation Kit Instructions: RC Ovens
Instructions for Applying Kit #4523368
This kit is for a convection
RC, 36” oven
only
. For a Standard 36” oven, use Kit #4522559
Installation Prerequisites:
RC Oven, Piezoelectric Ignition
U-Burner with no welded bracket
Tools Needed:
Wrenches
Small Hacksaw (for extension installation if required)
Screwdrivers (Robertson, Flat), long and short
Riveter
Electrical Tape
Parts:
Part #
Description
Quantity
1415703
Baso Safety Valve
1
4522554
7/16” x 10” Flex Tube
2
4522558
Pre-
bent 3/16” Tubing
1
076050-89
3/16” Union
1
M231
1/4IN X 3/16IN CC COMP Nut
2
M126
1/4IN TO 3/16IN SLEEVE - Ferrule
2
1095499
7/16cc
– 3/8 NPT Straight Connector
2
4522557
Valve Bracket
1
F60
#10 x 5/8 Sheet Metal Screw
4
M123
7/16IN C.C. COMPRESSION - Nut (for Flex Tube end)
2
M122
7/16IN C.C. BALL SLEEVE - Ferrule (for Flex Tube end)
2
F312
LOCK NUT-10-24 K-LOCK - Nut (for Baso Valve)
1
F587
BOLT # 10-24 x 2-1/4 SL - Bolt (for Baso Valve)
1
4522556
Redesigned Kick Panel
1
4522201
Welded Bracket Oven Burner
1
F32
#10-24 x ½ Pan HD Type F Screw (For Pilot Bracket)
1
070239-10
RC Pilot Natural Gas
1
078239-11
RC Pilot Propane
1
M124
¼” Tubing Ferrule
1
M125
¼” Comp. Nut
1
1415000
Robertshaw Thermocouple
1
4521446
¼” x 12” Flex Tube
1
4523367
MANUAL-HIGH HEAT KIT-RC
1
G7227-1
Lighting Instructions
1
M121
Rivet
2
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
03/09/09 P/N 4523367 Page 3 3) Unscrew Igniter Bracket Unscrew the two screws holding down the igniter bracket to the orifice bracket. Left: Before removal, location of screws shown by arrows Right: After removal 4) Remove Door Springs Once the springs are removed, the oven door will be free to ...
03/09/09 P/N 4523367 Page 5 For the door hinge with a microswitch: Unscrew the microswitch bracket from the oven frame. It is important that the microswitch be removed prior to removing the spring to prevent damage to the microswitch when the springs are reinstalled later. Microswitch bracket he...
03/09/09 P/N 4523367 Page 7 6) Install Extension Fitting (if applicable) If pilot gas tube going into the valve already has an extension piece (short piece of tubing plus 3/16” brass fitting), unscrew the shorter piece of tubing and proceed to Step 13. Otherwise, follow these steps to install the ...
