Fujitsu TX200FT S2 - Manuals

Fujitsu TX200FT S2 – Manual in PDF format online.

Manuals:

Manual

Manual Fujitsu TX200FT S2

Summary

Page 2 - Checking location before installing the server; Conditions; Remove the inner rail from the slide

2 4 Checking location before installing the server n Conditions �� ...

Page 3 - Fasten the server to the rack.; Install the second enclosure to the rack

3 5 Attach M5 rack nuts. Use 4U for each enclosure. Insert the rack nuts in the 2nd and 11th hole posi- tions, counting up from the base of the server, from inside of the rack bracket. �� ...

Page 4 - Connecting peripheral devices; Connecting the LAN cables

4 5 Connecting peripheral devices Peripheral devices, such as the keyboard and mouse, etc., are connected to the server in the following order. l Connecting the LAN cables l Connecting the display, keyboard and mouse �� ...

Page 5 - User information

5 6 Deciding required information before running mini-setup of the OS Before running mini-setup of the OS decide the following information. - User information (User and password)- Owner information- Validation interval at automatic shutdown (for UPS use only)- Network Configuration Decide and enter ...

Page 6 - Validation interval at automatic shutdown; Network configuration

6 n Validation interval at automatic shutdown This setting is required for the use of UPS. For details about various settings, refer to "3.4 UPS Settings" in the "User's Guide". The numbers in brackets ( ) are setting examples. Item Actual Setting Parameters Time Validation interval ...

Page 7 - Turning on the power and run mini-setup of each OS; Running mini-setup of the CoServer1; Check that the FTvirtual Server LAN; Press the power switch on the FT1.; following parameters.

7 7 Turning on the power and run mini-setup of each OS This section explains how to run mini-setup of CoServer1, CoServer2 and FTvirtual Server.To run mini-setup of FTvirtual Server, CoServer1 and 2 must already be run mini-setup. Run mini-setup in the following order. (1) Turn on the FT1 power and ...

Page 8 - Running mini-setup of the CoServer2; Logon to FTvirtual Server.; Running mini-setup of the FTvirtual server

8 5 Click [Yes]. CoServer restarts.After restarting, the POST screen (or "PRIMERGY" logo) appears. n Running mini-setup of the CoServer2 The running mini-setup procedure is the same as for CoServer1. Press the power switch on the front of FT2 and turn on the power supply. For details about f...

Page 9 - Right-click on the FTvirtual Server icon; erties] window and Endurance Manager; If optional devices have been added; Turning the server off

9 8 Right-click on the FTvirtual Server icon and select "Properties". The [Component Properties] window appears. 9 Select "FTvirtual Server" from the tree on the left, check "enabled" in "Auto- matic start" and click [Apply]. A red warning message will appear in the t...

Page 10 - Connecting the remaining LAN cables; ●Connecting the LAN cables; Pre-operation settings; After running mini-setup of the OS, refer to the; Support and Service; PRIMERGY information; Before requesting repairs

10 9 Connecting the remaining LAN cables After turning off the server, connect the remaining LAN cables as described below. In the FT-system, all FTvirtual Server LAN (application data transmission), CoServer Link, and CoServer LANs are used to control the system so it is important not to forget to ...

Page 11 - Non-durable components; Contact Information

11 Also read the points to note about requesting repairs be- forehand in "User's Guide 7.10.2 Contacting Maintenaice Support". Print the "Configuration Sheets" - "Accident Sheet" and en- ter the checked information. Be careful not to lose this sheet, as you must provide this ...

Page 12 - Notes

12 このマニュアルはリサイクルに配慮して製本されています。不要になった際は、回収・リサイクルに出してください。 Notes Data Backup To protect data stored in this device (including basic software and application software), perform backup and other necessary operations. Note that data protection is not guaranteed when repairs are performed. It is the cus...