Fujitsu TX200FT S2 - Manual
Fujitsu TX200FT S2 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Checking location before installing the server; Conditions; Remove the inner rail from the slide
- Page 3 – Fasten the server to the rack.; Install the second enclosure to the rack
- Page 4 – Connecting peripheral devices; Connecting the LAN cables
- Page 5 – User information
- Page 6 – Validation interval at automatic shutdown; Network configuration
- Page 7 – Turning on the power and run mini-setup of each OS; Running mini-setup of the CoServer1; Check that the FTvirtual Server LAN; Press the power switch on the FT1.; following parameters.
- Page 8 – Running mini-setup of the CoServer2; Logon to FTvirtual Server.; Running mini-setup of the FTvirtual server
- Page 9 – Right-click on the FTvirtual Server icon; erties] window and Endurance Manager; If optional devices have been added; Turning the server off
- Page 10 – Connecting the remaining LAN cables; ●Connecting the LAN cables; Pre-operation settings; After running mini-setup of the OS, refer to the; Support and Service; PRIMERGY information; Before requesting repairs
- Page 11 – Non-durable components; Contact Information
- Page 12 – Notes
1
�����������
����������������������������������������������
��������������������������������������������������
���������������������������������������������������������������
����������������������������������������������������������������
TX200FT S2
1
Checking the items
supplied
Using the "Contents List", check that no supplied
or attached items are missing. If any items are
missing, contact an office listed in the "Contact
Information.
■PRIMERGY TX200FT S2 Manuals
Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD.
[CD-ROM Drive] :\MANUAL\INDEX.PDF
Manuals can be displayed using Acrobat
®
Reader
®
or Adobe
®
Reader
®
. If using Acrobat
®
Reader
®
, use version 4.0 or later.
2
Checking "Safety Pre-
cautions"
Before using this server, be sure to check the at-
tached "Safety Precautions" guidelines.
Also check the guidelines when connecting, installing
internal options and setting up this server.
3
Installing internal options
If internal options have been purchased separately, install them before installing the Operating System.
n
Points to note when installing
internal options
When installing internal options, perform operations after
reading the following manuals.
������������
"Chapter 5 Installing Internal Options"
���������������
"PRIMERGY ServerBooks"/
"Supplement"
When installing memory or hard disk, always install the
same capacity of memory or hard disk to both enclo-
sures.
n
Available internal options and
installation locations
��������������������
�����������������������������
��������������
����������������������
�������������������������
���������������
�������
������
After installing internal options, check that the order and
location of installation are correct and cables are cor-
rectly attached.
B7FH-3821-01EN-00
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 4 Checking location before installing the server n Conditions ������������������������������������������������������������������������� �������������������������� ������������������������������������������������������������������������� ��������������� � �������������� �������� ������������������ ...
3 5 Attach M5 rack nuts. Use 4U for each enclosure. Insert the rack nuts in the 2nd and 11th hole posi- tions, counting up from the base of the server, from inside of the rack bracket. ���������������������� ��������������������������� ������������������� ���������������������� ���������������������...
4 5 Connecting peripheral devices Peripheral devices, such as the keyboard and mouse, etc., are connected to the server in the following order. l Connecting the LAN cables l Connecting the display, keyboard and mouse �������������������������������������������������� ����������������� ��������������...
