Fujitsu D2530 - Manuals

D2530 (Econel 200 S2) Technical Manual 7 2 Important notes In this chapter you will find essential information regarding safety when working with your server. V CAUTION! With the system board installed you must open the system to access the system board. How to access the system board of your system...

8 Technical Manual D2530 (Econel 200 S2) Notes on safety Important notes V ● Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. There is a danger of burns! ● Transmisson lines to peripheral devices must be adequately shield...

10 Technical Manual D2530 (Econel 200 S2) CE Certificate Important notes Notes about boards ● During installation/deinstallation of the system board, observe the specific instructions described in the service manual for the server. ● Remove the plug from the mains outlet so that system and system bo...

D2530 (Econel 200 S2) Technical Manual 11 Important notes Environmental Protection 2.3 Environmental Protection Environmentally friendly product design and development This product has been designed in accordance with standards for ”environmen-tally friendly product design and development“. This mea...

12 Technical Manual D2530 (Econel 200 S2) Environmental Protection Important notes Returning, recycling and disposal For details on returning and reuse of devices and consumables within Europe, refer to the “Returning used devices” manual, or contact your Fujitsu Siemens Computers branch office/subs...

D2530 (Econel 200 S2) Technical Manual 13 Features Overview 3 Features 3.1 Overview Processors – 2 x Intel ® Xeon™ Dual Core processors – 2 processor sockets Dual LGA771 for Intel ® Xeon™ Dual Core processor with 1333/1066/667 MHz front side bus – suppor ts Intel ® Extended Memory 64 Technology (EM6...

D2530 (Econel 200 S2) Technical Manual 15 Features Main memory 3.2 Main memory The system board suppor ts up to 8 Gbyte main memory. 4 slots (2 banks with 2 modules) are available for the main memory. Each memory bank can be populated with 512 Mbyte, 1 Gbyte or 2 Gbyte FBD533/PC2-4200F Fully Buffere...

16 Technical Manual D2530 (Econel 200 S2) PCI bus Features 3.3 PCI bus Figure 3: PCI slots PCI slots The following table shows an overview of the PCI slots: PCI IRQ Line x - Assignment of the PCI interrupts PCI IRQ Line x defines which ISA interrupts are used for the separate PCI slots. If you selec...

D2530 (Econel 200 S2) Technical Manual 17 Features PCI bus The PCI interrupts INTA#, INTB#, INTC# and INTD# are available for each PCI slot (except the PCI-Express slots). The same interrupt can be assigned simultaneously to several PCI boards. You should avoid this condition due to reduced performa...

18 Technical Manual D2530 (Econel 200 S2) Screen resolution Features 3.4 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the system board. If you are using an external screen controller, you will find details of...

D2530 (Econel 200 S2) Technical Manual 19 Features Temperature / system monitoring Fan control The fans are controlled according to temperature. Sensor monitoring The removal of, or a fault in, a temperature sensor is detected. Should this happen all fans monitored by this sensor run at maximum spee...

20 Technical Manual D2530 (Econel 200 S2) Connectors and jumpers Features 3.6 Connectors and jumpers Figure 4: Schematic overview of the system board D2530 1 = KBPWR (jumper) 15 = USBPW 3/4 (jumper) 2 = USBPW 1/2 (jumper) 16 = USB 3/4 3 = power supply ATX 17 = BPSMB 4 = PC98 18 = floppy disk 5 = pow...

22 Technical Manual D2530 (Econel 200 S2) Connectors and jumpers Features LAN_EN (24) LAN_BW (25) LED 5V Standby(A) 3.6.1 External connectors Figure 5: External connectors of the system board D2530 1-2 onboard LAN enabled (default) 2-3 onboard LAN disabled (PCI LAN controller) 1-2 LAN bandwidth sett...

D2530 (Econel 200 S2) Technical Manual 25 4 Replacing the lithium battery In order to save the system information permanently, a lithium battery is installed to provide the CMOS-memory with a current. When the charge is too low or the battery is empty, a corresponding error message is provided. The ...

D2530 (Econel 200 S2) Technical Manual 27 Abbreviations The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described system board. AC Altern...

Comments on System Board D2530 for Econel 200 S2 D2530 (Econel 200 S2) Comments Suggestions Corrections ✁ Submitted by Fujitsu Siemens Computers GmbHUser Documentation81730 MünchenGermany Fax: (++49) 700 / 372 00000 e-mail: [email protected] http://manuals.fujitsu-siemens.com