Page 2 - Comments... Suggestions... Corrections...; Copyright and Trademarks
Comments… Suggestions… Corrections… The User Documentation Department would like toknow your opinion of this manual. Your feedback helpsus optimize our documentation to suit your individual needs. Fax forms for sending us your comments are included inthe back of the manual. There you will also find ...
Page 3 - Contents
D2530 (Econel 200 S2) Technical Manual Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.2 CE Certificate . . . . . . . ...
Page 5 - Introduction; Notational conventions
D2530 (Econel 200 S2) Technical Manual 5 1 Introduction This technical manual describes the system board D2530, which can be equipped with one or two Intel ® processors. Further information about drivers is provided in the readme files on the hard disk, on the supplied "ServerSupport" or ...
Page 7 - Important notes; Notes on safety
D2530 (Econel 200 S2) Technical Manual 7 2 Important notes In this chapter you will find essential information regarding safety when working with your server. V CAUTION! With the system board installed you must open the system to access the system board. How to access the system board of your system...
Page 8 - Batteries
8 Technical Manual D2530 (Econel 200 S2) Notes on safety Important notes V ● Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. There is a danger of burns! ● Transmisson lines to peripheral devices must be adequately shield...
Page 10 - Notes about boards; CE Certificate
10 Technical Manual D2530 (Econel 200 S2) CE Certificate Important notes Notes about boards ● During installation/deinstallation of the system board, observe the specific instructions described in the service manual for the server. ● Remove the plug from the mains outlet so that system and system bo...
Page 11 - Environmental Protection
D2530 (Econel 200 S2) Technical Manual 11 Important notes Environmental Protection 2.3 Environmental Protection Environmentally friendly product design and development This product has been designed in accordance with standards for ”environmen-tally friendly product design and development“. This mea...
Page 12 - Returning, recycling and disposal
12 Technical Manual D2530 (Econel 200 S2) Environmental Protection Important notes Returning, recycling and disposal For details on returning and reuse of devices and consumables within Europe, refer to the “Returning used devices” manual, or contact your Fujitsu Siemens Computers branch office/subs...
Page 13 - Features; Overview; Processors
D2530 (Econel 200 S2) Technical Manual 13 Features Overview 3 Features 3.1 Overview Processors – 2 x Intel ® Xeon™ Dual Core processors – 2 processor sockets Dual LGA771 for Intel ® Xeon™ Dual Core processor with 1333/1066/667 MHz front side bus – suppor ts Intel ® Extended Memory 64 Technology (EM6...
Page 15 - Main memory; Module population
D2530 (Econel 200 S2) Technical Manual 15 Features Main memory 3.2 Main memory The system board suppor ts up to 8 Gbyte main memory. 4 slots (2 banks with 2 modules) are available for the main memory. Each memory bank can be populated with 512 Mbyte, 1 Gbyte or 2 Gbyte FBD533/PC2-4200F Fully Buffere...
Page 16 - PCI bus; PCI slots
16 Technical Manual D2530 (Econel 200 S2) PCI bus Features 3.3 PCI bus Figure 3: PCI slots PCI slots The following table shows an overview of the PCI slots: PCI IRQ Line x - Assignment of the PCI interrupts PCI IRQ Line x defines which ISA interrupts are used for the separate PCI slots. If you selec...
Page 17 - Device
D2530 (Econel 200 S2) Technical Manual 17 Features PCI bus The PCI interrupts INTA#, INTB#, INTC# and INTD# are available for each PCI slot (except the PCI-Express slots). The same interrupt can be assigned simultaneously to several PCI boards. You should avoid this condition due to reduced performa...
Page 18 - Screen resolution; Temperature / system monitoring; Temperature monitoring
18 Technical Manual D2530 (Econel 200 S2) Screen resolution Features 3.4 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the system board. If you are using an external screen controller, you will find details of...
Page 19 - Sensor monitoring
D2530 (Econel 200 S2) Technical Manual 19 Features Temperature / system monitoring Fan control The fans are controlled according to temperature. Sensor monitoring The removal of, or a fault in, a temperature sensor is detected. Should this happen all fans monitored by this sensor run at maximum spee...
Page 20 - Connectors and jumpers
20 Technical Manual D2530 (Econel 200 S2) Connectors and jumpers Features 3.6 Connectors and jumpers Figure 4: Schematic overview of the system board D2530 1 = KBPWR (jumper) 15 = USBPW 3/4 (jumper) 2 = USBPW 1/2 (jumper) 16 = USB 3/4 3 = power supply ATX 17 = BPSMB 4 = PC98 18 = floppy disk 5 = pow...
Page 22 - External connectors
22 Technical Manual D2530 (Econel 200 S2) Connectors and jumpers Features LAN_EN (24) LAN_BW (25) LED 5V Standby(A) 3.6.1 External connectors Figure 5: External connectors of the system board D2530 1-2 onboard LAN enabled (default) 2-3 onboard LAN disabled (PCI LAN controller) 1-2 LAN bandwidth sett...
Page 25 - Replacing the lithium battery
D2530 (Econel 200 S2) Technical Manual 25 4 Replacing the lithium battery In order to save the system information permanently, a lithium battery is installed to provide the CMOS-memory with a current. When the charge is too low or the battery is empty, a corresponding error message is provided. The ...
Page 27 - Abbreviations
D2530 (Econel 200 S2) Technical Manual 27 Abbreviations The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described system board. AC Altern...
Page 33 - Comments
Comments on System Board D2530 for Econel 200 S2 D2530 (Econel 200 S2) Comments Suggestions Corrections ✁ Submitted by Fujitsu Siemens Computers GmbHUser Documentation81730 MünchenGermany Fax: (++49) 700 / 372 00000 e-mail: [email protected] http://manuals.fujitsu-siemens.com
