Fagor 30i-T - Manuals

V0612 - 20i-T / 30i-T - Installation/Operation - DRO operation - (5/32) 2 DRO operation 2.1 Display modes MM / INCH conversion To display the position of the axes either in millimeters or inches by pressingthis key depending on whether the INCH led is off or on respectively. Fine / coarse resolution...

V0612 - 20i-T / 30i-T - Installation/Operation - DRO operation - (7/32) 2.2.1 Example Using the lower figure, let us imagine we wish to make a part in which threeholes have to be drilled with the coordinates stated. It is clear that theblueprint will only reflect the incremental coordinates (I) or t...

V0612 - 20i-T / 30i-T - Installation/Operation - DRO operation - (9/32) 2.3 Machine Reference selection and search Although it is not absolutely necessary, it is recommended to use thereference marks (Io) of the feedback system in order to set a machine zeropoint. This allows the user to reference t...

(10/32) - DRO operation - Installation/Operation - 20i-T / 30i-T - V0612 2.4 Operation with tools 2.4.1 Tool Preset Up to 20 tools may be preset on this DRO model (from "tool 0" to "tool 19").The unit stores in its internal memory the relative offsets of all the tools withrespect to ...

V0612 - 20i-T / 30i-T - Installation/Operation - DRO operation - (11/32) 2.5 Special operations 2.5.1 Scaling factor It is possible to apply a scaling factor within ±9.999 for mold makingapplications: The DRO will then show the axis position resulting from multiplying its realposition by the 'value'...

(12/32) - DRO operation - Installation/Operation - 20i-T / 30i-T - V0612 Tool change at any known point of the part: - Touch the part with the tool. - Go into HOLD mode. The reading for that axis freezes with the current value. - Remove the tool to be replaced and insert the new one. - Approach the ...

V0612-20i-T / 30i-T - Installation/Operation - DRO installation - (15/32) 3 DRO installation 3.1 Installation of the built-in model Dimensions of the enclosure hole for inserting the DRO Built-in DRO insertion Bolt ISO 7380M4 x 10 Inox Nut DIN 985M4 Inox

(16/32) - DRO installation - Installation/Operation - 20i-T / 30i-T - V0612 3.2 Rear panel On the back of the unit the following items may be found: 1. Three-prong power connector for AC and ground connection. 2. M6 mm terminal for general machine ground connection. 3. Mounting bracket Some of the f...

V0612-20i-T / 30i-T - Installation/Operation - DRO installation - (17/32) WARNING Do not handle the connectors while the unit is under power. Before handling the connectors (mains, feedback, etc.) make sure that the unit is not under power. It is NOT enough to turn the display off by using the [on/o...

V0612-20i-T / 30i-T - Installation/Operation - DRO installation - (19/32) The axis status will then switch to one of the following: Ready Correct feedback setup Repeat Wrong feedback setup, the process should be repeated. Error Error in the feedback system. Note: If the feedback device is a steel ta...

(20/32) - DRO installation - Installation/Operation - 20i-T / 30i-T - V0612 To get into parameter editing The dro displays must be on, reading mode and press the following keys: The X axis display shows the word " COdE ". 060496 The displays of the DRO show PAR00 . Once in regular display mo...

V0612-20i-T / 30i-T - Installation/Operation - DRO installation - (21/32) 3.7 Parameters to configure axis position reading and display. The digits of digital parameters refer to the digits on the axis displays so digit"1" (that can be changed with the [1] key) corresponds to the rightmost d...

(22/32) - DRO installation - Installation/Operation - 20i-T / 30i-T - V0612 PAR02 TTL multiplying factor (subdivision). Independent for each axis. Options: x4, x2, x1 and x0.5. The factory setting is x4 and it is the one used for FAGOR linear encoders. When using rotary encoders on linear axes, it s...

(24/32) - DRO installation - Installation/Operation - 20i-T / 30i-T - V0612 Therefore, when using standard Io's, this parameter must be assigned thevalue of the distance from the machine zero point to the feedback referencepoint.Numeric value in resolution units for each axis. Factory setting: 0. Th...

V0612-20i-T / 30i-T - Installation/Operation - DRO installation - (25/32) PAR15 Multi-point leadscrew error compensation. Important: Before capturing data for an accuracy graph, the axis (axes) must behomed (referenced) because the compensation will not be applied until they are homed. To use this c...

V0612 - 20i-T / 30i-T - Installation/Operation - Appendix - (27/32) 4 Appendix 4.1 UL seal See "UL seal" page 16. 4.2 CE seal Warning Before starting up the DRO, carefully read the instructions of Chapter 2 in the Installation Manual. The DRO must not be powered-on until verifying that the m...

V0612 - 20i-T / 30i-T - Installation/Operation - Appendix - (29/32) It is recommended to mount the DRO vertically, so its power switch of the back panel is at a distance between 0.7 m (27.5inches) and 1.7 m (5.6 ft) off the floor and away from coolants, chemicalproducts, blows etc that could damage ...

(30/32) - Appendix - Installation/Operation - 20i-T / 30i-T - V0612 32 4.2.3 Warranty terms WARRANTY All products manufactured or marketed by Fagor Automation has a warrantyperiod of 12 months from the day they are shipped out of our warehouses.The mentioned warranty covers repair material and labor...

(32/32) - Appendix - Installation/Operation - 20i-T / 30i-T - V0612 32 4.4 Maintenance Cleaning: An accumulation of dirt in the equipment can act as a screen preventingproper dissipation of the heat generated by the internal electronic circuits withthe consequent danger of overheating and DRO fault....