DeLonghi Split Air Conditioner- Manuals

DeLonghi Split Air Conditioner– Installation Manual in PDF format online.

Manuals:

Installation Manual

Installation Manual DeLonghi Split Air Conditioner

Summary

Page 2 - INDEX; SINGLE SPLIT; User

INDEX SINGLE SPLIT 1 English 11/2002 Safety standards 2 Identification of the parts 4 Remote control 6 Operating modes 8 AUTO mode 9 TIMER mode 9 DRY mode 10 SLEEP mode 10 Maintenance 11 Troubleshooting 12 Installation instructions 13 Installation of the indoor unit 15 Installation of the outdoor un...

Page 3 - SAFETY STANDARDS AND WARNINGS

SINGLE SPLIT 2 English 11/2002 Use the power supply voltage shown on the ratingplate. Keep the power switch or plug clean. Connectthe power cable correctly and securely to the out-let, avoiding the risk of electric shock or fire due toinsufficient contact. Check that the outlet is suitable for the p...

Page 4 - Working temperature range; Maximum cooling

SINGLE SPLIT 3 English 11/2002 Keep the appliance at least 50cm from flamma-ble substances (alcohol, etc .) or from pres-surised containers (e.g. spray cans). Selecting the most suitable temperature will avoiddamaging the appliance. The direction of air flow must be adjusted correct-ly. The louvers ...

Page 5 - IDENTIFICATION OF THE PARTS; INDOOR UNIT

SINGLE SPLIT 4 English 11/2002 IDENTIFICATION OF THE PARTS AUTO TEST RUN STOP AUTO STOP 1 4 5 11 10 7 9 6 8 12 4 4 14 13 2 3 Air inlet INDOOR UNIT OUTDOOR UNIT The above figure represents a simplified layout of the appliance and may not correspond to theappearance of the unit actually purchased. U I...

Page 6 - This comes on when the appliance is in heating mode.

SINGLE SPLIT 5 English 11/2002 1 2 3 4 5 AUTO TEST RUN STOP 1. Manual switch This is used to start the appliance if the remote con-trol is not working.* 2. Heating indicator This comes on when the appliance is in heating mode. 3. Cooling indicator T h i s c o m e s o n w h e n t h e ap p l i a n c e...

Page 7 - REMOTE CONTROL

REMOTE CONTROL SINGLE SPLIT 6 English 11/2002 3 4 1 5 6 7 10 2 8 9 1. Liquid crystal display Displays all the operating modes. 2. MODE button Used to select the operating mode. 3. FAN button Used to set the fan speed, in sequence, to automatic, low, medium, high. 4. SLEEP button Used to set or cance...

Page 9 - OPERATING MODES

SINGLE SPLIT 8 English 11/2002 OPERATING MODES OPERATING MODES 1. Selecting the operating mode Each time that the MODE button is pressed the oper- ating mode is changed, in the following sequence: FULL AUTO COOLING DRY FAN ONLY HEATING 2. FAN mode Each time that the FAN button is pressed, the speed ...

Page 10 - AUTO MODE; this mode, the temperature and the fan speed are set auto-; The operating mode and the temperature setting; In AUTO mode, the pre-set temperature is 25°C in cooling; TIMER MODE; FAN ONLY; Room temperature

AUTOMATIC START After having switched the appliance off, press the T-ON button to set the time you want the air-conditioner to switch back on; pressing the T-ON button again increases the time by 30 minutes, until a maximum of 24 hours from when the TIMER is set. E.g.: If the setting is performed at...

Page 11 - DRY MODE; To set the requested temperature.; DEHUMIDIFICATION MODE; SLEEP MODE

DRY MODE SINGLE SPLIT 10 English 11/2002 SLEEP MODE Press the MODE button until displaying the COOL ( ) or DRY ( ) mode. To set the requested temperature. Press the SLEEP ( ): button: the set temperature will be increased by 1°C in one hour and 2°C in two hours. The appliance will then hold the temp...

Page 12 - MAINTENANCE; Replace the filters with the side marked as “FRONT”

MAINTENANCE SINGLE SPLIT 11 English 11/2002 Unplug the appliance from the power outlet To remove the front panel, pull it outwards, as shown by the arrows in the figure Replace the filters with the side marked as “FRONT” facing the outside Clean with a soft damp cloth, using water or detergent, then...

Page 13 - TROUBLESHOOTING

TROUBLESHOOTING SINGLE SPLIT 12 English 11/2002 The appliance doesn't work • Are the protection devices or fuses faulty?• Have the connections come loose or the cable unplugged?• At times operation is stopped to protect the appliance.• Is the voltage above 244V or below 206V?• Is the TIMER-ON functi...

Page 14 - INSTALLATION INSTRUCTIONS; Insulation tape

INSTALLATION INSTRUCTIONS SINGLE SPLIT 13 English 11/2002 A I INSTALLATION DIAGRAM The distance from the ceiling must begreater than 150mm The distance from thewall must be greaterthan 150mm The distance betweent h e a i r i n l e t a n d t h ew a l l mu s t b e g re a t e rthan 300mm The distance f...

Page 15 - The appliance shall not be installed in the

SINGLE SPLIT 14 English 11/2002 Minimum installation height of the indoor unit (Min. 2.5m). Places suitable for the installation of the outdoor unit • Install the unit in a suitable and well-ventilated site; avoid installing it in places where there are possible leaks of combustible gases. • Observe...

Page 16 - INSTALLATION OF THE INDOOR UNIT

INSTALLATION OF THE INDOOR UNIT SINGLE SPLIT 15 English 11/2002 A I 1 2 3 4 1. INSTALLATION OF THE FASTENING PLATE Select the position for installing the fastening plate, according to of the location of the indoor unit and the layout of the pipes. Adjust the level of the fastening plate, using a str...

Page 17 - Model

SINGLE SPLIT 16 English 11/2002 Thermal insulation lining • Position the drain hose under the pipes. • Insulation material: polythene foam, thickness greater than 6mm. The drain hose must be supplied by the user. • The drain hose must run downwards, to assist drainage. • Do not bend the drain hose, ...

Page 18 - Indoor unit

SINGLE SPLIT 17 English 11/2002 3. CONNECTING THE CABLE Indoor unit Connect the power cable to the indoor unit by connect- ing the wires to the terminals on the control panel indi- vidually, according to the connection to the outdoor unit. To make the connection to the indoor unit ter- minal, remove...

Page 19 - PFor connections between the indoor and outdoor unit

SINGLE SPLIT 18 English 11/2002 Indoor unit Outdoor unit Power cable Blue Blue Yellow/Green Yellow/Green Brown Brown 1N 2 3 1N 2 3 Terminal Terminal Terminal Terminal Indoor unit Outdoor unit Power cable Blue Blue Yellow/Green Brown Brown Red Red 1N 2 3 1N 2 3 CONNECTION DIAGRAM Check that the colou...

Page 20 - Install the drain fitting and the drain hose (heat

VENTING THE AIR INSTALLATION OF THE OUTDOOR UNIT SINGLE SPLIT 19 English 11/2002 A I Refrigerant flow direction 2-way valve (6) Open 1/4 turn valve cap (1) Turn (8) Tighten (2) Turn 3-way valve (8) Tighten (1) Turn (7) Turn to fully open the valve (7) Turn to fully open the valve (8) Tighten Service...

Page 21 - Numero Verde

NOTES USEFUL INFORMATION SINGLE SPLIT 20 English 11/2002 • Read this manual before installing and use the appliance. • Check that air does not enter the refrigerant system and that there are no leaks of refrigerant when the air-condi- tioner is moved. • Run a test cycle after the installation of the...