DeLonghi DGHS70- Manuals

DeLonghi DGHS70– User Manual in PDF format online.

Manuals:

User Manual

User Manual DeLonghi DGHS70

Summary

Page 2 - DESCRIPTION OF THE HOT PLATES; NG

2 DESCRIPTION OF THE HOT PLATES TYPES: PCFZ 60 V4 - PCFZ 60 N4 TYPES: PCFZ 70 V5 - PCFZ 70 N5 DGHS70 NG Propane Gas 1 Ultra rapid burner of MJ/h 11.9 11.9 2 Rapid gas burner of MJ/h 10.4 10.8 3 Semirapid gas burner of MJ/h 6.3 6.3 4 Auxiliary gas burner MJ/h 3.6 3.6 5 Electric plate Ø 145 mm 6 Ename...

Page 3 - USE

3 USE 1) BURNERS A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners as described below: - Manual ignition Push and turn the knob corresponding ...

Page 4 - COOKING HINTS FOR GAS HOBS

4 USE - Where the appliance is installed in marine craft or in caravans, it shall not be used as a space heater. - If the built-in hot plate has a lid, any spilt food should be immediately removed from this before it is opened. If the appliance has a glass lid, this could shatter when the hot plate ...

Page 7 - To place a pan on the plate before switching this on.

7 USE WARNINGS: When the plate is switched on for the first time, or if it has remained unused for a long period, it should be dried for 30 minutes on switch position n° 1. This will eliminate any moisture that may have been absorbed by the insulating material. To correctly use the appliance, rememb...

Page 8 - CLEANING; Do not force the taps if they are difficult open or close.

8 CLEANING IMPORTANT: Always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation. 3) HOT PLATE Periodically wash the hot plate, the enamelled stell pan support, the enamelled burner caps “C” and the burner heads “T” (see fig. 8) with lukewarm soapy ...

Page 9 - INSTALLATION

9 INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER CAUTION: This appliance must be installed in accordance with these installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, AS5601 / AG 601 – Gas Installations a...

Page 10 - ) FIXING THE HOT PLATE; COMPLY WITH THE DIMENSIONS

10 INSTALLATION 4) INSTALLING THE HOT PLATE Check that the appliance is in a good condition after having removed the outer packaging and internal wrappings from around the various loose parts. In case of doubt, do not use the appliance and contact qualified personnel. Never leave the packaging mater...

Page 12 - Do not use any naked flame to check for leaks.

12 INSTALLATION 6) GAS CONNECTION The gas connection is located in the rear and on the underside of the appliance 100 mm from the right hand side. 1. After connecting the gas supply, check the piping and connections for leaks using a soap and water solution. The presence of bubbles indicates a leak,...

Page 13 - ) ELECTRICAL CONNECTION; THE APPLIANCE MUST BE EARTHED.

13 INSTALLATION 7) ELECTRICAL CONNECTION The appliance is supplied with a 1800 mm long flexible supply lead. The point of attachment for this lead is located at the rear and on the underside of the appliance 380 mm from the right hand side. The voltage and power consumption are detailed on the under...

Page 14 - ADJUSTMENTS; “Reduced rate” adjustment

14 ADJUSTMENTS Always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations. Our burners do not require primary air adjustment. a) Data Label The Data Label is located on the undersi...

Page 15 - CONVERSION PROCEDURE; Burner Main

15 CONVERSION PROCEDURE 9) Propane Gas to Natural Gas conversion procedure Appliance models: Gas stainless steel hotplate models: 4 Burners 2 Burners 1 Burner 1. Remove each burner cap and burner skirt. 2. Remove the Propane Gas main injector with a 7 mm/VF tube spanner and replace with the appropri...

Page 17 - BURNER ARRANGEMENT ON THE HOT PLATE

17 CONVERSION PROCEDURE BURNER ARRANGEMENT ON THE HOT PLATE TABLE BURNERS GAS NORMAL PRESSURE INJECTOR DIAMETER NOMINAL HEAT INPUT (MJ/h) N° DESCRIPTION (kPa) (1/100 mm) MAX. 1 ULTRA RAPID PROPANE NATURAL 2.75 1.00 95 155 11.9 11.9 2 RAPID PROPANE NATURAL 2.75 1.00 91 145 10.8 10.4 3 SEMIRAPID PROPA...

Page 18 - SERVICING; 1) COMPONENTS REPLACEMENT; Clean the cone and its housing using a cloth soaked in diluent.

18 SERVICING WARNING: Servicing should be carried out only by an Authorized person/Service agent. 11) COMPONENTS REPLACEMENT NOTE: BEFORE ANY MAINTENANCE REQUIRING REPLACEMENT OF A COMPONENT IS UNDERTAKEN ENSURE THAT THE ELECTRICAL LEAD HAS BEEN ISOLATED AND REMOVED FROM THE POWER POINT. To replace ...

Page 19 - Gas hot plate

19 SERVICING CABLE TYPES AND SECTIONS TYPE OF HOT PLATE TYPE OF CABLE SINGLE - PHASE POWER SUPPLY Gas hot plate H05 RR - F Section 3 X 0.75 mm 2 Mixed hot plate with 1 electrical plate H05 RR - F Section 3 X 1 mm 2 ATTENTION!!! If the power supply cable is replaced, the installe should leave the gro...

Page 20 - SERVICE AND MAINTENANCE; Servicing the appliance:

20 SERVICE AND MAINTENANCE If the ignition spark fails to ignite or does not light the gas, check the following items before calling our Customer Service Centre to obtain the nearest Authorised Delonghi Service Agent: Burner is reassembled and located correctly. Spark electrode and white ceramic are...