Crimestopper RS900 - Manuals

Page 2 - VENDORS

TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….……………………………2 Using the Remote Transmitter…………………………………………………………………………………..….…….3 Remote Engine Control…………….…..…………………………………………………………………….………….3-7 Convenience and Safety Features……………………………….……………………………………...……..………8-9 Tra...

Page 3 - REMOTE ENGINE CONTROL; REMOTE ENGINE STARTING - SUCCESSFUL START:

USING THE REMOTE TRANSMITTER (RS900) The transmitter supplied with this system has Four (4) buttons / channels. The button configuration is Factory-set and unchangeable. (RS901 model does not include remote transmitters: For add-on / OEM use only) #3 #1 TRANSMITTER BUTTONS #2 #4 START LOCK TRUNK REM...

Page 4 - IGN; REMOTE ENGINE STARTING - UNSUCCESSFUL START; NO FURTHER; TURNING OFF A REMOTE STARTED ENGINE:

AFTER IGN 3 STARTER THEN FLASH 1X SOLID SOLID SEC. START REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2 nd and 3 rd time. For hard sta...

Page 6 - ENTERING A VEHICLE DURING “IDLE-DOWN” or “INFINITY RUN” MODES:; SOLID; FLASH 2X; INDEFINITELY after the programmed run time elapses; INFINITY RUN MODE – EXITING THE VEHICLE: (NOT AVAILABLE ON RS901)

IGN SOLID OFF UNLOCK START ENTERING A VEHICLE DURING “IDLE-DOWN” or “INFINITY RUN” MODES: 1) With engine running in "IDLE DOWN" (parking lights ON), unlock door via remote or key. 2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset) 3) Turn Ignition to ON/RUN posi...

Page 7 - solid while motor runs indefinitely or until fuel supply runs out.; FLASH FOR PROGRAMMED; TIMED 4 HOUR SELF START MODE

2) Parking Lights will start flashing, and doors will unlock. 3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running. 4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36, or 48 minutes and then switch to solid while motor runs i...

Page 8 - PRESS 1X; FLASH 4X; CONVENIENCE AND SAFETY FEATURES

6) The vehicle will Start by itself every 4 hours until driven with key or started via the remote control. IGN SOLID OFF UNLOCK PRESS 1X WITHIN 10 SEC. LIGHTS OFF 5 SEC. FLASH 4X LOCK S T A R T S T A R T CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system en...

Page 9 - REMOTE PANIC (When used with Optional HORN HONK); time within 3 seconds will provide a horn chirp for audible; VALET MODE / STARTER DISABLE OVERRIDE

the remote control must still be utilized to operate the Starter disable feature. REMOTE PANIC (When used with Optional HORN HONK) For personal safety this unit now includes a panic feature. To sound the vehicle car horn, press the Lock Button on the remote for more than 2 seconds. The vehicle horn ...

Page 10 - TRANSMITTER PROGRAMMING; TRANSMITTER PROGRAMMING:; code

of an external relay. This system must be programmed to allow the relay to work as a starter disable. PASSIVE STARTER DISABLE (Optional) This RS900 includes a programmable feature to allow the Optional Starter Disable to activate automatically 1 minute after the ignition is turned off. This programm...

Page 11 - WAIT FOR

and 4 flashes for the 4 th code. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off and close hood. See diagram below. TRANSMITTER PROGRAMMING: IGN OFF WAIT FOR 4 FLASHES PRESS 4X's FLASH 2, 3, or 4 X's (GRAY WIRE GROUNDED) RS900 V IGN OFF START 2...

Page 12 - CAR; TROUBLESHOOTING: “BEFORE YOU CALL” SECTION; UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START:

START CAR I CAR II Slide RS 900 V CAR I / CAR II OPERATION TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY STILL FUNCTIONS NORMALLY): The unit is in Valet mode. Turn Ignition ON, press and hold valet/programming button for 6 seconds then turn key off. Unit is ...

Page 13 - remote start unit will make up to 3 attempt to start the engine.

NO RESPONSE FROM REMOTE TRANSMITTERS: (4 Parts) 1. Check for proper power/ground wiring connections at module. 2. Check Antenna Module connection. The antenna module included with this system must be plugged in. 3. Transmitters may need to be programmed to the unit. See transmitter programming steps...