Crimestopper RS-850 - Manuals

Page 2 - TABLE OF CONTENTS; System Diagram..............................................................................................................................15; INSTALLATION CAUTIONS & WARNINGS; wiring. Extending these wires could result in poor performance.; DO NOT; parts in the vehicle.; DO NOT; result in damage to the unit not covered under warranty.; DO NOT

TABLE OF CONTENTS Pre-Installation Considerations…………...……...………………………………………………………………Front Cover Cautions & Warnings…….…………..….……..…..……………………………………………………………….…..……2 Wiring……..…………………………....……………………………………………………………………………….…….3-5 Wiring High-Current Connector…….………………...………………………………………………………………….....

Page 3 - WIRING

WIRING 2 PIN PLUG-PROGRAM/OVERRIDE SWITCH: This switch is used for programming features, transmitters, and valet mode. 2 PIN PLUG-(OPTIONAL) LED: The LED is used as an indicator for Valet, Programming, and for use as security deterrent with the optional ANTI-GRIND/STARTER DISABLE feature installed. ...

Page 6 - IGNITION SWITCH WIRING; ACC

IGNITION SWITCH WIRING PARKING LIGHTS FUSE RED WHITE 30A FUSE RED +10A MAX. 30A + - BROWN PINK FUEL ENGINE BATTERY PUMP ECU GRAY + STARTER - COIL IGN 1 ACC Heat/AC Diagram Not to Scale. For illustration purposes only. Your vehicle may differ. IGN. Switch 6

Page 7 - POWER DOOR LOCK WIRING; Plug-in pulse inverter that converts the; DETERMINING DOOR LOCK TYPE:; Databus Systems 2003 GM Trucks & SUV’s, ‘99-04 Jeep Grand Cherokee

POWER DOOR LOCK WIRING PIN 1: BLUE: (-) Negative pulse for UNLOCK Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive type for ...

Page 8 - BASIC DOOR LOCK DIAGRAMS; NEGATIVE TRIGGER DOORLOCK WIRING

BASIC DOOR LOCK DIAGRAMS NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS AFTERMARKET MOTOR/DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRI...

Page 9 - “SMART TACHLESS” MODE; as described below, or use “Tach Reference” mode.; “SMART TACHLESS” ADJUSTMENT:

“SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor ea...

Page 10 - Tach Reference Mode; These Tach Signal locations mentioned are

TACH (RPM) REFERENCE MODE / TACH FINDER MODE / TACH PROGRAMMING Tach Reference Mode provides reliable remote starting performance though engine speed sensing. When using Tach Reference Mode, the Red/White wire is used for Tach signal [Engine RPM] input. Most modern engines include various points whe...

Page 11 - TRANSMITTER PROGRAMMING; code and; CAR

TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The RS800 allows storage of up to 4 different transmitter codes. 1. Open Hood. (Ground Gray wire.) 2. Turn key to the ON position. 3. Press Programming button 4 times, then after a few seconds the unit will ...

Page 12 - OPTION PROGRAMMING; OPTIONS

OPTION PROGRAMMING IMPROVED: Now you can program multiple options in one session if you start with the lowest option and continue on to higher options [if needed] without repeating the steps #1-3. For example, you can change Option #2 to “ON” by pressing the lock button, then you can continue pressi...

Page 13 - OPTION DESCRIPTIONS:

OPTION PROGRAMMING OPTION DESCRIPTIONS: 1. NOT USED: No Option 2. Door Lock Pulse Time: Controls the amount of time for lock/unlock pulse. The standard setting is 0.75 for most vehicles. A 3 sec. setting is required for 1980’s/90’s European Vacuum or Pneumatic door lock systems. 3. Double Unlock Pul...

Page 14 - REMOTE START TROUBLESHOOTING “Before You Call Section”; UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START:

REMOTE START TROUBLESHOOTING “Before You Call Section” UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for about 4 seconds until LED goes out. The unit is now out of valet mode and should perform a remote start. U...

Page 15 - NOTE: USE EXTERNAL RELAYS FOR HIGH-CURRENT; BATTERY

TRANSMISSION PROGRAM/ OVERRIDE PARKING LIGHTS SW ITCH ECU RS-850 ANTENNA/ RECEIVER PLUG LED COIL + - (-) UNLOCK OUTPUT +12 V FOR RELAYS 12A MAX. (-) LOCK OUTPUT ENGINE ECU GREEN BLUE RED WHITE FUEL PUMP PINK RED H/V/AC CONTROL BROWN GRAY RED YELLOW (-)IGN OUT IGN 1 RED/W HITE TACH INPUT ORANGE/BLACK...

Page 16 - ONLINE TECHNICAL SUPPORT