Crimestopper RS-7 - Manuals

Crimestopper RS-7 – Manual in PDF format online.

Manuals:

Manual

Manual Crimestopper RS-7

Summary

Page 2 - PLAN OUT YOUR INSTALLATION

2 TABLE OF CONTENTS Pre-Installation Considerations….………...……...………………………………………………………………..….………..2 Installation Cautions & Warnings………………………………………………………………………………..….....……..…3 Wiring……..……………………....…………………………………………………………………………………...………...3-7 Wiring High-Current Wiring…..…….…………………………………………………………...

Page 3 - INSTALLATION CAUTIONS & WARNINGS; result in damage to the unit not covered under warranty.; DO NOT; WIRING; BLACK: MAIN SYSTEM GROUND

3 INSTALLATION CAUTIONS & WARNINGS FOR SAFETY REASONS, DO NOT INSTALL in vehicles with MANUAL TRANSMISSIONS .** If accidentally left in gear, a remote started vehicle could become a self-propelled threat to life and property. DO NOT extend the Remote start ignition harness length. Mount the modu...

Page 5 - TAN

5 WIRING TAN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT This output is programmable for 3 modes of operation. See Programming Option #9 Section. 1. 30 second Dome Light output. 2. Momentary ½ second output (Default). 3. Momentary Push and Hold. The output stays on until Transmitte...

Page 7 - PINK: NEGATIVE GLOW PLUG

7 WIRING GRAY: (-) NEGATIVE HOOD PIN SWITCH REQUIRED FOR PROGRAMMING Connect the Gray wire to a switch that is at ground when the hood is open. If an existing switch is not available, then we recommend one to be installed. W hen this wire is grounded, the remote start is inhibited. The unit will not...

Page 9 - POWER DOOR LOCK WIRING CONNECTOR; 2V W hen using external relays (TERM 86)

9 Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive type for Positive Door Lock systems. CS-610S1: Aftermarket door lock actu...

Page 10 - BASIC DOOR LOCK DIAGRAMS; NEGATIVE TRIGGER DOORLOCK WIRING

10 BASIC DOOR LOCK DIAGRAMS AFTERMARKET MOTOR/DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 30 87A 30 87A 30 87A 30 87A + L CUT UL CUT MASTER SWITCH NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOOR...

Page 11 - “SMART TACHLESS” MODE; “SMART TACHLESS” ADJUSTMENT:

11 “SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor...

Page 12 - TACH FINDER & USEFUL TIPS

12 TACH FINDER & USEFUL TIPS TACH FINDER MODE: This Tach Finder mode can assist in locating a Tach source for your installation. W hen following the steps, the unit will begin to flash the parking lights if you have the Red/W hite wire connected to a tach source. If lights do not flash, then try...

Page 13 - TACH PROGRAMMING & TACH SIGNALS; INTRODUCTION; EXAMINING THE TACH FREQUENCY WITH A DIGITAL MULTI-METER

13 TACH PROGRAMMING & TACH SIGNALS INTRODUCTION Tach signals will vary in levels and frequencies depending on many factors including the type of vehicle and the source of the signal. The signals from a vehicle’s injector wire and coil pack wire can vary greatly even on the same engine. The tach ...

Page 14 - TIMED CRANK MODE; HOW TO USE THIS FEATURE:; attempt and may require a 2

14 TIMED CRANK MODE This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses a timed cranking output combined with the use of the Red/W hite tach wire as an engine ON/OFF monitor. The Red/W hite Tach wire must still be used in this mode of ope...

Page 15 - DIESEL GLOW PLUG DELAY; OPTION PROGRAMMING; OPTION PROGRAMMING CHART BEGINS ON NEXT PAGE

15 DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-W ait to Start Circuit. This may be needed for various reasons. If your vehicle does not have a viable W ait to Start Circuit , or you cannot locate and identify the circuit, the...

Page 16 - Pink wire; OPTION PROGRAMMING TABLE; Option

16 OPTION PROGRAMMING To Engage Option Programming: 1. Open hood, If no hood pin switch is installed, then ground the Gray hood pin wire. Turn Key to the ON position. Do not start vehicle ( Pink wire must be connected!) 2. Press the program Valet button 5 times. W ait for the unit to flash the light...

Page 18 - OPTION DESCRIPTIONS; Remote Start & Auxiliary Output – Button Press Selection:

18 OPTION DESCRIPTIONS 2. Auto Lock Unlock: The option controls whether the doors will automatically lock/unlock on your vehicle when driving or with turning the Ignition ON/OFF. If the Auto Lock feature is turned on, and the system is in Tach mode, then the doors will lock as the engine RPM’s incre...

Page 19 - Unlock With Trunk Pop or Trunk Pop Only:

19 OPTION DESCRIPTIONS 9. Brown Output Wire Function: Trunk Pop or Dome Light Output This option controls how the Brown output wire of the unit functions, either for Trunk pop or for Dome light illumination. 10. 12V “Wake up” Pulse: This option allows the unit to provide a 1-second pulse on the Pink...

Page 21 - TRANSMITTER PROGRAMMING; Pink wire must be connected!; code, so repeat this step as needed with up to 3 additional; code, 4 flashes after the 3; code and 0 for 4

21 TRANSMITTER PROGRAMMING Transmitter Programming: (Excludes RS-00 model without remotes) Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be learned at time of programming!! These systems a...

Page 22 - VEHICLE PROGRAMMING; TRANSMIT ICON

22 2 VEHICLE PROGRAMMING Your remotes have the ability to control a second vehicle with a Crimestopper system installed. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 12) at the second vehicle and learn YOUR remot...

Page 23 - MANUAL TRANSMISSION MODE; MANUAL TRANSMISSION EXIT PROCEDURE:; The 10-second time threshold activates when the door CLOSES.; Note: Turbo Timer Mode doesn’t work in Manual Transmission Mode.

23 MANUAL TRANSMISSION MODE MANUAL TRANSMISSION INSTALLATION: (PINK WIRE) After programming option #11 for manual transmission mode, the pink “Glow plug” input wire becomes a Door Pin input that must be used for the manual transmission remote start procedure. This wire is a negative input only. If y...

Page 24 - JUMPER PIN DIAGRAMS; JUMPER PINS; Control

24 JUMPER PIN DIAGRAMS Jumper pins are used to change/configure the operation of the on board multi-function output PINK W HITE wire and the Parking Light W HITE wire. See the diagrams below for Jumper Pin configurations. JUMPER PINS Parking Lights JUMPER PINS Start 2IGN 2ACC 2 Control Module High C...

Page 25 - ANTENNA DIAGRAM; WINDSHIELD; DATA PORT; There are 2 types of

25 ANTENNA DIAGRAM Antenna should be located at top of widow at least one inch away from metal surface. WINDSHIELD ANTENNA LOCATIONS DATA PORT This unit includes DP Technology that will allow you to directly Plug-In our Data Port Bypass Modules. There are 2 types of Protocol, OFA series and SL serie...

Page 26 - LOW CURRENT PLUG; 2 PIN LOW CURRENT PLUG

26 LOW CURRENT PLUG Orange/black Yellow/black Black White Red/white Orange Brown Yellow/white Ground RUN (Ign 1) (-) Start Activation (-) (-) (-) OEM Arm Parking Lights Trunk Pop Relay Remote Output 86 85 87 30 87A (+ or -) 12 PIN LOW CURRENT PLUG 1 2 0 3 4 5 6 7 8 ENGINE MONITOR TACH Pink Glow Plug...

Page 27 - HIGH CURRENT PLUG; PIN HIGH CURRENT PLUG

27 HIGH CURRENT PLUG 6 PIN HIGH CURRENT PLUG START IGN START / IGN / ACC ACC Control START 2 IGN 2 ACC 2 Fuel A/C - Heater Pump Coil Jumper Select Default = IGN 2 STARTER 12 VoltBattery (+) (-) Fuse Fuse Gray Pink Pink/White Brown Red Red IGNITIONSWITCH Diagram not to scale, for illustration purpose...

Page 28 - REMOTE START DIAGNOSTICS

28 REMOTE START DIAGNOSTICS If the system flashes the parking lights one to three times and doesn’t attempt remote, it means the following: 1 Parking Light Flash = Problem with Brake Switch. 2 Parking Light Flashes = Problem with Hood Switch. 3 Parking Light Flashes = Valet Service Mode. 7 Parking L...