Crimestopper FS-20 - Manuals

Page 2 - TABLE OF CONTENTS; OPERATION CAUTIONS & WARNINGS; and its

2 TABLE OF CONTENTS Operation Cautions & Warnings……..…………..…………………………………………………………….………2 The Remote Control…..……………………………...……………………..……………………….…….….…..……..3 . Operating Instructions………………………..……………….…….………………….…….…………...……….…4-7 Car Jack Protection..…………..…………..……………………………………………...…………………..…………8...

Page 3 - THE REMOTE CONTROL; Button; Side Button

3 THE REMOTE CONTROL Button Button Functions Button Options Lock Doors & Arm System Press and hold 3 Seconds for Panic Mode Unlock Doors and Disarm System Unlock Doors and Disarm System Trunk Release Aux # 1 Press and Release for Trunk Pop (Aux #1) Silent Arm / Disarm Aux #2 Press and Release fo...

Page 4 - OPERATION INSTRUCTIONS; DISARMING

4 OPERATION INSTRUCTIONS ARMING To arm the alarm and lock the doors, press the Lock button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed. The re...

Page 5 - OPERATING INSTRUCTIONS; Doors will not lock if they are open to

5 OPERATING INSTRUCTIONS ARM / DISARM WITH IGNITION ON (PROGRAM OPTION #15) This feature allows the system to be armed or disarmed while the ignition is in the ON position or vehicle is running. The feature is disabled by default and should not be used under normal operating conditions. On an instal...

Page 6 - EMERGENCY OVERRIDE / DISARM

6 OPERATING INSTRUCTIONS EMERGENCY OVERRIDE / DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open the door with the key, which will activate the alarm. Turn the ignition on and press the override/program button for about 5 seconds ...

Page 7 - ALARM TRIGGERING

7 OPERATING INSTRUCTIONS VALET MODE (Solid LED) To disable the Alarm system for vehicle service or otherwise, turn the ignition on and press the override/program button 4-5 seconds until the dash LED turns on solid and you hear (1) siren chirp. Repeat the process to exit VALET mode and the system wi...

Page 8 - CARJACK PROTECTION; ACTIVE CARJACK

8 CARJACK PROTECTION ACTIVE CARJACK This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See page 10. W hen the Ignition is on (vehicle is running), press and hold button #3 (AUX) for 3 seconds. Parking lights will flash TW ICE to confi...

Page 9 - TRANSMITTER PROGRAMMING; LED will be on solid.; transmitter for up

9 TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times, Siren 4 times, Horn 4 times and...

Page 10 - VEHICLE OPERATION / PROGRAMMING; Push Side Button to; VEHICLE 2

10 2 VEHICLE OPERATION / PROGRAMMING 2 VEHICLE CONTROL Your remotes have the ability to control a second vehicle with a Crimestopper system installed. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 9) at the second...

Page 11 - BATTERY REPLACEMENT; To Replace the Batteries:

11 BATTERY REPLACEMENT To Replace the Batteries: The Remote Control uses Two CR-2016 Lithium 3 Volt Batteries. Simply remove the two Phillips screws holding the back cover in place. Insert the new batteries with the (-) end toward the circuit board. CR 2016 Lithium BACK COVER SCREWS REMOVE