Crimestopper EZ-777FM - Manuals

Crimestopper EZ-777FM – Manual in PDF format online.

Manuals:

Manual

Manual Crimestopper EZ-777FM

Summary

Page 2 - BEFORE BEGINNING; may include extra relays or Anti-Theft System Bypass modules.

TABLE OF CONTENTS Pre-Installation Considerations……….………...……...……………………………………………………………….……2 Cautions & Warnings…….…………...….……..…..……………………………………………………………….…..……3 Wiring……..…………………………....……………………………………………………………………………….…….3-7 Wiring High-Current Connector…….………………...…………………………………………………………………........

Page 3 - INSTALLATION CAUTIONS & WARNINGS; result in damage to the unit that is not covered under warranty.; DO NOT; WIRING

INSTALLATION CAUTIONS & WARNINGS **FOR SAFETY REASONS, DO NOT INSTALL in vehicles with MANUAL TRANSMISSIONS .** If accidentally left in gear, a remote started vehicle could become a self-propelled threat to life and property. DO NOT extend the Remote start ignition harness length. Mount the modu...

Page 5 - BROWN; Connect to+12V for Positive circuits

WIRING PIN 8: BROWN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT This output is programmable for two modes of operation. See Programming Option Section. Mode (1) DEFAULT: Provides a Ground pulse when button #3 (Trunk) on the remote transmitter is pushed to activate a factory electri...

Page 7 - PIN 5: PINK: NEGATIVE or POSITIVE DIESEL GLOW PLUG INPUT

WIRING PIN 6: GRAY: (-) NEGATIVE HOOD PIN SWITCH (REQUIRED FOR PROGRAMMING) Connect the Gray wire to a switch that is at ground when the hood is open. If an existing switch is not available, then we recommend installing the supplied pin switch. When this wire is grounded, (hood is open) remote start...

Page 8 - SEE DIAGRAM on NEXT PAGE

WIRING: 7-PIN HIGH-CURRENT CONNECTOR BROWN: +12V STARTER OUTPUT 40A: Connect to circuit in the vehicle that has power ONLY while the STARTER MOTOR is CRANKING. GRAY: +12V ACCESSORY OUTPUT 40A: Connect to circuit in the vehicle that provides Accessory Power for systems such as HEAT and A/C. Typically...

Page 9 - IGN; OR; ACC

WIRING: 7-PIN HIGH-CURRENT CONNECTOR FUSE RED PINK/WHITE 30A FUSE RED 30A + - BROWN PINK FUEL ENGINE BATTERY PUMP ECU GRAY + STARTER - COIL IGN OR ACC H/V/AC Diagram not to scale, for illustration purposes only. Your vehicle may differ. IGN 2 ACC 2 TOP WHITE START 2 FUSE PARKING LIGHTS IF NECESSARY ...

Page 10 - POWER DOOR LOCK WIRING CONNECTOR; Plug-in pulse inverter that converts the; DETERMINING DOOR LOCK TYPE:

POWER DOOR LOCK WIRING CONNECTOR PIN 1: BLUE: (-) Negative pulse for UNLOCK Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive...

Page 11 - BASIC DOOR LOCK DIAGRAMS; NEGATIVE TRIGGER DOORLOCK WIRING

BASIC DOOR LOCK DIAGRAMS NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS AFTERMARKET MOTOR/DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRI...

Page 12 - “SMART TACHLESS” MODE; “SMART TACHLESS” ADJUSTMENT:

“SMART TACHLESS” MODE Your EZEE system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor each ti...

Page 13 - TACH FINDER & USEFUL TIPS; TACH FINDER TIP: Erratic vs. Consistent light flashing; range of the system.

TACH FINDER & USEFUL TIPS TACH FINDER MODE: This Tach Finder mode can assist in locating a Tach source for your installation. When following the steps, the unit will begin to flash the parking lights if you have the Red/White wire connected to a tach source. If lights do not flash, then try anot...

Page 14 - TACH PROGRAMMING & TACH SIGNALS; INTRODUCTION; These Tach Signal locations mentioned are provided

TACH PROGRAMMING & TACH SIGNALS INTRODUCTION Tach signals will vary in levels and frequencies depending on many factors including the type of vehicle and the source of the signal. The signals from a vehicle’s injector wire and coil pac wire can vary greatly even on the same engine. The tach sign...

Page 15 - TIMED CRANK MODE; HOW TO USE THIS FEATURE:; attempt and may require a 2

TIMED CRANK MODE This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses a timed cranking output combined with the use of the Red/White tach wire as an engine ON/OFF monitor. The Red/White Tach wire must still be used in this mode of operatio...

Page 16 - DIESEL GLOW PLUG DELAY; OPTIONS PROGRAMMING; OPTION PROGRAMMING CHART BEGINS ON NEXT PAGE

DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“Wait to Start Circuit”. This may be needed for various reasons. If your vehicle does not have a viable “Wait to Start Circuit”, or you cannot locate and identify the circuit, then ...

Page 17 - To Engage Option Programming:

OPTIONS PROGRAMMING To Engage Option Programming: 1. Open hood (If no hood pin switch is installed, then ground the Gray wire) 2. Turn Key to the ON position. (Do not start vehicle) 3. Press the valet/program button 5 times. After a few seconds the unit will flash the lights 5 times. 4. Press the va...

Page 19 - OPTION DESCRIPTIONS:

OPTIONS PROGRAMMING OPTION DESCRIPTIONS: 1. Engine Monitoring: This option sets how the unit monitors your engine. You can program either for Tach mode in which the unit uses a Tach signal (RPM) or for Tachless mode that monitors voltage level. See pages 11-15 for more information and additional ste...

Page 20 - Brown Output Wire Function: Trunk Pop or Dome Light Output

OPTIONS PROGRAMMING 7. Horn Chirps on Remote Start: This option allows the unit to provide 3 short chirps when for audible confirmation of a remote start. The horn output wire must be connected for this feature. 8. Lock During/After Remote Start: This option controls whether the unit will automatica...

Page 22 - code, 3 flashes for the 3

EZ-90 TRANSMITTER / 777TW1/TW2/FM TRANSCEIVER CODE LEARNING Transmitter/Transceiver Code Learning: (Excludes EZ-91 model without remotes) Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be l...

Page 24 - TROUBLESHOOTING: “BEFORE YOU CALL” SECTION; UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY):; on many late model vehicles.

TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY): The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for 5-6 seconds then turn key off. Unit is now out of valet mode and should remote start. If optional LED is in...

Page 25 - JUMPER PIN DIAGRAMS

JUMPER PIN DIAGRAMS Jumper pins are used to change/configure the operation of the on board multi-function output PINK/WHITE wire, the Parking Light WHITE wire and the PINK glow plug input wire. See the diagrams below for Jumper Pin configurations. JUMPER PLUG SIDE VIEW JUMPER PINS JP1 JUMPERS: IGN 2...

Page 26 - ANTENNA DIAGRAM; WINDSHIELD

ANTENNA DIAGRAM WINDSHIELD ANTENNA LOCATIONS Blue Plug Black Plug EZ-90 EZ-777TW1EZ-777TW2EZ-777FM Color of plug andreceptacle must match!! 26

Page 27 - BATTERY; VEHICLE

TRANSMISSION PROGRAM PARKING LIGHTS SW ITCH ECU EZ90/91 ANTENNA/RECEIVER PLUG LED (-) UNLOCK OUTPUT +12 V FOR RELAYS (-) LOCK OUTPUT ENGINE ECU GREEN BLUERED FUEL PUMP PINK RED BROWN GRAY RED W HITE +10A or -.5A OUTPUT IGN RED/W HITE TACH INPUT ORANGE/BLACK: (-)HOOD SW ITCH GRAY (+12V) BRAKE PEDAL R...

Page 28 - ONLINE TECHNICAL SUPPORT