Crimestopper CS-2013FM - Manuals

Crimestopper CS-2013FM – Manual in PDF format online.

Manuals:

Manual

Manual Crimestopper CS-2013FM

Summary

Page 2 - TABLE OF CONTENTS

TABLE OF CONTENTS Installation Cautions & Warnings…….………….…………………………...………………………………………………2-3 Suggested Component Mounting…………. ……...……………………………...…………………………….……………....3 Wiring Information……………………………….……………………………..……………………………...………….…….4-7 Power Door Lock Wiring...………………………..…………………………………….………………...

Page 3 - and its; INSTALLATION CAUTIONS & WARNINGS; DO NOT REMOTE START A VEHICLE IN A CLOSED AREA OR GARAGE!; DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED

Prior Intrusion Diagnostics………………………….………………………………………………………...……….…..……22 Remote Start Operation……………….…………………………………………………………………………..….……..22-23 Special LCD FM Remote-Pager Functions……….…………………………………………………………..………………24 INSTALLATION CAUTIONS & WARNINGS CRIMESTOPPER SECURITY PRODUCTS, INC. and its...

Page 4 - SUGGESTED COMPONENT MOUNTING; accessible by an intruder.; WIRING; RED; ACCESSORY Output; 0 PIN MAIN HARNESS PLUG:

SUGGESTED COMPONENT MOUNTING Control Module: Driver or Passenger side underdash, the unit should be placed as high as possible, not easily accessible by an intruder. Shock Sensor: Mount with wire ties to an under dash wire harness or fasten with screws to a panel. Siren: Under the hood to fender-wel...

Page 5 - Programmable Auxiliary Output Channel #2.; YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS; BLACK WIRE: SYSTEM CHASSIS GROUND

Programmable Auxiliary Output Channel #2. BLACK/WHITE WIRE: (-) DOME LIGHT ILLUMINATION (Optional, Requires Relay) Connect to terminal 85 of relay. This wire turns the dome light on for 30 seconds upon disarming of the alarm. If the ignition is turned on or the alarm is re-armed, the dome light will...

Page 6 - Connect to RED siren wire.; WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT

WHITE/BLACK WIRE: (-) HOOD/TRUNK TRIGGER (Mandatory For Hood Pin) Input trigger for a grounding hood or trunk pin switch and to inhibit remote start if the hood is open. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install a new p...

Page 7 - WIRING TABLE; COLOR; TACH SIGNAL INPUT (ENGINE RPM0

GREEN : (-) NEGATIVE LOCK Connect directly to negative lock/unlock systems. If vehicle uses RED: +12V For Relays positive door lock signals or reversing polarity type, then external BLUE: (-) NEGATIVE UNLOCK relays must be added. See Power Door Lock Wiring: Pages 8- 9. 4 PIN (WHITE) SENSOR PLUG: WHI...

Page 8 - POWER DOOR LOCK WIRING

12 GREEN (-) NEGATIVE DOOR TRIGGER INPUT 13 WHITE/BLACK (-) HOOD/TRUNK TRIGGER INPUT 14 ORANGE (-) ARMED OUTPUT (STARTER DISABLE) 15 VIOLET/WHITE (-) OEM FACTORY DISARM OUTPUT 16 WHITE/VIOLET (-) OEM FACTORY ARM OUTPUT 17 BROWN (+) SIREN POSITIVE OUTPUT 18 GRAY (-) NEG AUXILIARY CHANNEL OUTPUT #1 (T...

Page 9 - NEGATIVE TRIGGER DOORLOCK WIRING; POSITIVE TRIGGER DOORLOCK WIRING; SEPARATE DRIVER’S DOOR UNLOCK WIRING

NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS AFTERMARKET DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED ...

Page 12 - OPTION PROGRAMMABLE OPTIONS TABLE; Option # Option Description

LEARNING THE TACH (RPM) SIGNAL: 1. Have the Black/Gray Tach wire connected to your Tach source. 2. Start engine with key. 3. Within 10 seconds, press the valet/program button 5 times, the siren should chirp 3 times. 4. Push program button again (21) times, you should get a siren chirp for each butto...

Page 13 - OPTION PROGRAMMING

1. Passive Arming Disabled* Enable 2. Active Re-Arm Disabled* Enable 3. Silent Arm/Disarm Chirps* No Chirps 4. Lock when IGN turns ON/ Custom Override mode Enabled* Disabled Custom Override Mode 5. Unlock when IGN turns OFF Enabled* Driver’s door only NO IGN Unlock 6. Double Unlock Pulse 1 Pulse* 2 ...

Page 15 - DOOR OPEN WARNING; OR SECOND ARMED OUTPUT; armed output when system is armed.; REMOTE START WHILE IN VALET MODE

This option controls whether the doors will lock when Passive Arming occurs. Note: May increase the risk of locking keys in the vehicle. When selected ON, the alarm will lock the doors when passive arming. 9. REMOTE-LESS DISARM “BEACH MODE” (Note: this option also requires Passive arming/Passive loc...

Page 16 - Starter Output; OPTION RESET PROCEDURE PROGRAMMING; are in programming mode.; CUSTOM “PERSONAL” OVERRIDE CODE

18. REMOTE START ENGINE RUN TIME: Controls the amount of running time for remote start: 12 or 24 Minutes. 19. COLD START INTERVAL TIME Controls the time between remote engine starts when the “Cold Start” feature is activated: Every 1 or 2 hours. 20. TACH or TACHLESS MODE Controls whether the system ...

Page 17 - Turn ignition on and off 3 times within leaving it on the 3; will chirp 3 times if this was performed correctly.; press to get the remote to

Custom override allows the user to set a specific number of button presses (2 to 15) required to perform an emergency override/disarm of the alarm system. This helps to defeat the common perception of a thief that if you turn the vehicle’s ignition on and press the valet button, most alarms will shu...

Page 18 - ADDITIONAL TRANSCEIVER PROGRAMMING: 2-WAY FM REMOTE; indicating you are in feature programming mode.

ADDITIONAL TRANSCEIVER PROGRAMMING: 2-WAY FM REMOTE 1. Turn the ignition on, within 10 seconds press the override/program button 5 times. Siren will chirp 3 times indicating you are in feature programming mode. 2. Within the next 5 seconds, carefully press the override/program button 22 times. The s...

Page 19 - BUTTON 1; Not Used; ALARM OPERATION

OPERATION: (1-WAY REMOTE) 5-Button One-Way Remote Functions: PANIC BUTTON 1 BUTTON 3 BUTTON 2 BUTTON 4 BUTTON 5(ON SIDE) BANK #1 (Directly Press Buttons) Button 1: Arm / Lock (Hold 4 seconds for Panic) Button 2: Disarm / Unlock Button 3: Aux #1 (Trunk Release) Button 4: Remote Start (Hold 2 sec.) Bu...

Page 20 - TRIGGERING THE ALARM:

ALARM OPERATION DISARMING: Press Button #1 (Lock Symbol) on the 2-Way remote. For the 1-Way remote Press Button #2 (Unlock Symbol) to disarm. The 2-Way remote will confirm with an “UNLOCK” icon on the LCD display and an audible signal. At the vehicle, the siren will chirp (2) times and the lights wi...

Page 21 - alarm system depending on programming option #14 configuration.

To arm the system and bypass the shock for just that one time, press button #1 on either remote to arm, then within 10 seconds press Button #1 AGAIN. Siren will chirp 5 times and lights will flash 5 times. ALARM OPERATION VALET MODE: To disable the Alarm functions of the system while still allowing ...

Page 22 - activated upon door opening and the siren will begin to chirp.

ALARM OPERATION PASSIVE ARMING / PASSIVE LOCK MODES: (Programmable) If programmed for passive (Automatic) Arming, the system will Arm itself 30 Seconds after the ignition is turned off and the last door has been closed. The LED will begin flashing rapidly while counting down to Passively Arm. If a d...

Page 23 - Shock Sensor = 2 Flashes; REMOTE START OPERATION; REMOTE ENGINE START:

3. Insert key into the Ignition and turn to the ON position to disarm the alarm. If the key is not turned on within 10 second (i.e. Intruder) then your system will go into a full alarm trigger. PRIOR INTRUSION DIAGNOSTICS (ONE-WAY REMOTE ONLY) This system includes disarm diagnostics, (through the RE...

Page 24 - Examples of Idle Down uses:; Vehicle will self-start a maximum of 12 times

REMOTE START OPERATION IDLE-DOWN (Continued): Examples of Idle Down uses: • You pull up to a convenience store for a quick stop. The "Idle Down" mode keeps engine running when you exit the vehicle (with keys in hand) and arm the alarm. When you return, unlock/disarm alarm, turn ignition ON a...

Page 25 - SPECIAL 2-WAY LCD FM REMOTE-PAGER FUNCTIONS; Alarm Clock Setting:; Note: Alarm clock sounds one time for; To cancel an alarm that has already been set:; Note: The Remote Start Timer activates once for each

SPECIAL 2-WAY LCD FM REMOTE-PAGER FUNCTIONS Clock Setting: 1. Press and hold buttons #2 (Key Symbol) & #3 (Trunk Symbol) together until 2 beeps are heard. 2. Immediately release Buttons #2 & 3. 3. Observe the time display on the LCD screen. Press the #2 button to set the hour and press the #...