Crimestopper CS-2002DC SERIES III - Manuals

Page 2 - TABLE OF CONTENTS; Installation Cautions & Warnings..................................................................................................2; INSTALLATION CAUTIONS & WARNINGS; BEFORE BEGINNING; before jump starting, using a battery; DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED; column, or any other moving parts in the vehicle.

TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………….………………………………………………2 Control Module & Component Mounting……………...………………………..……………………….…………..3 Wiring……..……………………………………………………………………………………………………….…….3-6 Parking Light Jumper Diagram………………………………………………….………………………….…..……..5 Power Doo...

Page 3 - CONTROL MODULE & COMPONENT MOUNTING; Mount the red LED in a visible location on the dashboard or console.; WIRING

CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control unit in the engine compartment or where the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a conce...

Page 4 - BLACK WIRE: SYSTEM CHASSIS GROUND

WIRING BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short. YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOL...

Page 5 - Connect to RED siren wire from the Siren in the engine compartment.; WHITE WIRE: PARKING LIGHT

WIRING BLUE/WHITE WIRE: (-) PASSENGER(S) DOOR UNLOCK OUTPUT (Optional, requires relay) Connects to unlock circuit for passenger door(s) when using separate driver’s door unlock option. See SEPARATE DRIVER’S DOOR UNLOCK WIRING on Page 8 for some configuration options. BROWN WIRE: (+) SIREN OUTPUT (3 ...

Page 6 - Mount the LED in a visible location of the dash or console.; POWER DOOR LOCK WIRING

WIRING RED WIRE: +12V POWER INPUT (15 amp fuse) Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle battery positive terminal. 14 GA. BROWN WIRE: (On-board Starter Disable Relay) Cut the 14GA. Brown wire in half. Connect the 2 female...

Page 8 - SEPARATE DRIVER’S DOOR UNLOCK WIRING; NEGATIVE TRIGGER DOOR LOCKS

SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGATIVE TRIGGER DOOR LOCKS BLUE/WHITE GREEN RED BLUE DRIVER'S DOOR MOTOR 86 85 L L 87 UL UL 87A 30 FACTORY LOCK RELAYS +12V + FUSED UNLOCK WIRE CUT WIRING FOR REVERSE POLARITY DOOR LOCKS BLUE/W HITE GREEN FUSED RED +12V BLUE + MASTER 86 85 86 85 SW ITCH 86 85 87...

Page 9 - TRANSMITTER PROGRAMMING; This system will learn a maximum of 4 transmitters.; press to; OR

TRANSMITTER PROGRAMMING This system will learn a maximum of 4 transmitters. 1. Turn Ignition ON/OFF…ON/OFF …ON. You should hear (3) chirps. 2. Press the Program/Override Button 5 times and you should hear 5 light flashes and 5 siren chirps. (System is now in transmitter programming mode.) 3. Press a...

Page 10 - OPTION PROGRAMMING; PROGRAMMING OPTIONS CHART

OPTION PROGRAMMING 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long chirp. 2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to the feature list below. The siren will chirp for each button press...

Page 11 - Doors will not lock if they are open to prevent locking the keys in

OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle Horn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3 (Trunk) = Horn Chirps for Arm, ...

Page 12 - DOUBLE UNLOCK PULSE

OPTION PROGRAMMING 7. DOUBLE UNLOCK PULSE With this feature enabled, the unit will send 2 unlock pulses when the #2 Unlock button is pressed. 2 pulses are required for interfacing into some existing Factory Keyless Entry or Alarm systems on vehicles such as Nissan, VW, Toyota, and Lexus vehicles. 8....

Page 13 - on this alarm system. Press the program button 2-15 times only.

PROGRAMMABLE OPTION RESET Follow the steps below to reset ALL OPTION VALUES ON PAGE 10 TO FACTORY DEFAULT SETTINGS. 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long chirp. 2. Immediately press Button #3 (Trunk) on the remote. 3. The siren will chirp 4 tim...

Page 14 - OPERATING INSTRUCTIONS; BUTTON REMOTE TRANSMITTER:; BUTTON 1; Arm; ALARM TRIGGERING

OPERATING INSTRUCTIONS 5 BUTTON REMOTE TRANSMITTER: PANIC BUTTON 1 BUTTON 3 BUTTON 2 BUTTON 4 BUTTON 5(ON SIDE) BANK #1 (Directly Press Buttons) Button 1: Arm Button 2: Disarm Button 3: Aux #1 (Trunk) Button 4: Panic Button 5: (Change to BANK #2) BANK #2 (Press Button 5 FIRST, then within 3 seconds ...

Page 15 - REMOTE PANIC PROTECTION

OPERATING INSTRUCTIONS TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL) To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least 1½ seconds. If the system is armed, pressing Button #3 may or may not trip the alarm system when opening the tru...

Page 16 - EMERGENCY DISARM WITH CUSTOM OVERRIDE

OPERATING INSTRUCTIONS EMERGENCY DISARM WITH CUSTOM OVERRIDE If you have programmed your system for Custom Override, follow the same steps above (Emergency Override) while pressing the valet button 2-15 times as you have programmed. You must continue to hold the button down on the last press for 5 s...

Page 17 - IGNITION-CONTROLLED DOORLOCKS; Doors will not lock if they are open to; VEHICLE OPERATION; VEHICLE CONTROL

OPERATING INSTRUCTIONS IGNITION-CONTROLLED DOORLOCKS The doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off. This feature can be programmed on, off, or to lock the doors only. Doors will not lock if they are open to prevent locking the keys i...

Page 18 - CARJACK PROTECTION FEATURES; ACTIVE CARJACK

CARJACK PROTECTION FEATURES ACTIVE CARJACK This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See page 9. When the Ignition is on (vehicle is running), press button #4 (Panic). Parking lights will flash TWICE to confirm the Carjack co...

Page 19 - LED POD; DASH; Use

LED / VALET POD & SHOCK SENSORI LED / VALET BUTTON POD: DUAL ADJUST Smart Sense™ Shock Sensor: >Use the Green screw for Pre-warn adjustment >Use the Red Level for Shock trigger adjustment LED VALET/PROGRAM BUTTON SYSTEM LED POD GREEN RED Pre-Warn Trigger LED / VALET BUTTON MOUNTING: DASH U...