Chicago Electric 95380 - Manuals

Page 2 - SPECIFICATIONS; SAVE THIS MANUAL; GENERAL SAFETY RULES; WARNING! Read all instructions; WORK AREA; Keep your work area clean and well lit.

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 2 SPECIFICATIONS Motor 110 VAC / 60 Hz / 11 A / 1-3/4 HP / 20,000 Maximum RPM Router Type Plunge Router with Brake Router Power Cord SJT 16 AWG x 2C Router Table Power Switch Rocker (ON/OFF) with Safety Key Router Table Power Cord 16...

Page 5 - SPECIFIC SAFETY RULES

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 5 SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Router and its Table. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Avoid unintentional starting. Make...

Page 7 - GROUNDING; Grounded Tools: Tools with Three Prong Plugs; reducing the risk of electric shock.; WARNING

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 7 examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, dependin...

Page 8 - should look like those in the following illustration.; -Prong Plug and Outlet; Double Insulated Tools: Tools with Two Prong Plugs; Standard Association, and the National Electrical Code.; Symbology; UNPACKING; When unpacking, check to make sure all the parts shown on the; Parts List on; are included. If any parts are missing or broken, please call Harbor

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 8 3. The tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See 3-Prong Plug and Ou...

Page 9 - ASSEMBLY INSTRUCTIONS; Assembly Diagram; Always make sure the Power Switch (2B) of the; “OFF”; position and the unit is unplugged from; To Attach the Legs to the Table:; over the ends of the Screws as shown in Figure A.

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 9 ASSEMBLY INSTRUCTIONS Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on pages 16 and 17 . CAUTION! Always make sure the Power Switch (2B) of the Router Table is in ...

Page 10 - To Mount The Router Table On A Workbench:; Make sure the Router Table is securely attached; To Install The Miter Gauge:; Slide the Miter Gauge assembly forward and backward in the

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 10 To Mount The Router Table On A Workbench: 1. CAUTION! Make sure the Router Table is securely attached to a dry, flat, level, sturdy workbench surface capable of supporting the weight of the unit, accessories, and workpieces. 2. At...

Page 11 - The Router Table Power Switch/Outlets Assembly:; Figure D; The Power Switch/Outlets (2B) assembly is equipped with a Safety Key

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 11 To Connect A Vacuum Hose To The Dust Port: Figure C DUST PORT (1-3/8” OUTSIDE DIAMETER) The Dust Port of the Router Table is 1-3/8” O.D. (outside diameter) and is located at the rear of the Router Table. Use an automotive hose cla...

Page 13 - BASIC OPERATING INSTRUCTIONS

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 13 BASIC OPERATING INSTRUCTIONS WARNING! Use safety equipment. Always wear ANSI- approved safety impact eye goggles. Dust mask or respirator, and hearing protection must be used for appropriate conditions. 1. Make sure the Power Swit...

Page 14 - TROUBLESHOOTING; Problem

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 14 TROUBLESHOOTING Problem Possible Solution Router will not run. 1. Make sure the Power Switch of the Router Table is in its “ON” position.2. Make sure the Power Switch of the Router is in its “ON” position.3. Make sure the Power Co...

Page 15 - both; PLEASE READ THE FOLLOWING CAREFULLY

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 15 INSPECTION, MAINTENANCE, AND CLEANING 1. CAUTION! Always make sure the Power Switch of the Router Table is in its “OFF” position and the Router Table is unplugged from its electrical outlet prior to performing any inspection, main...

Page 16 - PARTS LISTS & ASSEMBLY DIAGRAMS; Part

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 16 PARTS LISTS & ASSEMBLY DIAGRAMS PARTS LIST & ASSEMBLY DIAGRAM A - ROUTER Part Description Qty. 1A Machine Screw 2 2A Template Guide 1 3A Base Assy. 1 4A Nut Clamp 1 5A Collet Chuck 1 6A Lock Piece 1 7A Lock Screw 1 8A Lock...

Page 17 - PARTS LIST & ASSEMBLY DIAGRAM B - ROUTER TABLE

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 17 PARTS LIST & ASSEMBLY DIAGRAM B - ROUTER TABLE Part Description Qty. 1B Leg 4 2B Power Switch/Outlets 1 3B Fixed Stand 1 4B Guiding Groove 1 5B Work Table 1 6B Fence 1 7B Knob 3 8B Guard 1 9B Adjustable Fence 1 10B Wrench (21m...

Page 18 - LIMITED 90 DAY WARRANTY; WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 18 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials...